Használati útmutató DeWalt DWFP12658

DeWalt tűzőgép DWFP12658

Olvassa el alább 📖 a magyar nyelvű használati útmutatót DeWalt DWFP12658 (48 oldal) a tűzőgép kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/48
1 - ENG
DWFP12658
ROOFING COIL NAILER
CLOUEUSE POUR TOITURE À CLOUS EN BOBINE
CLAVADORA PARA TECHADO A RESORTE
INSTRUCTION MANUAL
GUIDE D’UTILISATION
MANUAL DE INSTRUCCIONES
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-D WALTe • www.dewalt.com
9R199590RA
INSTRUCTIVO DE OPERACIÓN, CENTROS
DE SERVICIO Y PÓLIZA DE GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
INSTRUCTIONS DE FONCTIONNEMENT,
CENTRES DE SERVICE, POLITIQUE DE
GARANTIE. AVERTISSEMENT : LISEZ CES
INSTRUCTIONS AVANT D'UTILISER L'APPAREIL.
2 - ENG
• Actuating tool may result in flying debris, collation
material, or dust which could harm operator’s eyes.
Operator and others in work area MUST wear safety
glasses with side shields. These safety glasses must
conform to ANSI Z87.1 requirements (approved glasses
have “Z87” printed or stamped on them). It is the
employer’s responsibility to enforce the use of eye
protection equipment by the tool operator and other
people in the work area. (Fig. A)
• Alwayswearappropriate personalhearingandother
protection during use. Under some conditions and
duration of use, noise from this product may contribute
to hearing loss. (Fig. A)
• Useonlyclean,dry,regulatedair.Condensationfrom
an air compressor can rust and damage the internal
workings of the tool. (Fig. B)
• Regulate air pressure. Use air pressure compatible
with ratings on the nameplate of the tool. [Not to
exceed 120 psi (8.3 bar).] Do not connect the tool to a
compressor rated at over 200 psi. The tool operating
pressure must never exceed 200 psi even in the event of
regulator failure. (Fig. C)
• Only use an air hose that is rated for a maximum
working pressure of at least 150 psi (10.3 bar) or
150% of the maximum system pressure, whichever is
greater. (Fig. D)
• Do not use bottled gases to power this tool. Bottled
compressed gases such as oxygen, carbon dioxide,
nitrogen, hydrogen, propane, acetylene or air are not
70 psi
4.9 bar
Fig. C
Fig.B
Fig. A
Fig. D
IMPORTANT SAFETY INSTRUCTIONS
FOR PNEUMATIC TOOLS
SAVE THESE INSTRUCTIONS
WARNING: When using any pneumatic tool, all safety precautions, as outlined below,
should be followed to avoid the risk of death or serious injury. Read and understand all
instructions before operating the tool.
DEFINITIONS - SAFETY GUIDELINES
The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.
DANGER: will Indicates an imminently hazardous situation which, if not avoided,
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially haz ard ous situation which, if not avoided, may
result in minor or mod er ate injury.
NOTICE: Used without the safety alert symbol indicates a situation which, if not
avoided, may property damage. result in
3 - ENG
for use with pneumatic tools. Never use combustible
gases or any other reactive gas as a power source for this
tool. Danger of explosion and/or serious personal injury
may result. (Fig. E)
• Use couplings that relieve all pressure from the tool
when it is disconnected from the power supply.
Use hose connectors that shut off air supply from
compressor when the tool is disconnected. (Fig. F)
• Disconnect tool from air supply when not in use.
Always disconnect tool from air supply and remove
fasteners from magazine before leaving the area or
passing the tool to another operator. Do not carry
tool to another work area in which changing location
involves the use of scaffoldings, stairs, ladders, and
the like, with air supply connected. Do not make
adjustments, remove magazine, perform maintenance
or clear jammed fasteners while connected to the
air supply. If the contact trip is adjusted when the tool
is connected to the air supply and nails are loaded,
accidental discharge may occur. (Fig. G)
• Connect tool to air supply before loading fasteners
to prevent an unintentional fastener discharge during
connection. The tool driving mechanism may cycle
when the tool is connected to the air supply. Do
not load fasteners with the trigger or the contact trip
depressed to prevent unintentional driving.
• Do notremove,tamper with,or otherwisecause the
tool, trigger, or contact trip to become inoperable.
Do not tape or tie trigger or contact trip in the on
position. Do not remove spring from contact trip. Make
daily inspections for free movement of trigger and contact
trip. Uncontrolled discharge could result.
• Inspect tool before use. Do not operate a tool if
any portion of the tool, trigger, or contact trip is
inoperable, disconnected, altered, or not working
properly. Leaking air, damaged parts or missing parts
should be repaired or replaced before use. Refer to
Repairs. (Fig. H)
• Donotalterormodifythetoolinanyway.(Fig. I)
• Alwaysassumethatthetoolcontainsfasteners.
• Donotpointthetoolatco-workersoryourselfatany
time. No horseplay! Work safe! Respect the tool as a
working implement. (Fig. J)
• Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control. When tool is not in use, it should be locked
in a safe place, out of the reach of children.
• Removefingerfromtriggerwhennotdrivingfasteners.
• Never carry tool with finger on trigger. Accidental
discharge could result. Using the trigger lock-off will
prevent accidental discharge.
Fig. E
Fig. F
Fig. I
Fig. J
Fig. G
Fig. H

Termékspecifikációk

Márka: DeWalt
Kategória: tűzőgép
Modell: DWFP12658

Szüksége van segítségre?

Ha segítségre van szüksége DeWalt DWFP12658, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók tűzőgép DeWalt

DeWalt

DeWalt DWFP71917 Útmutató

1 Október 2024
DeWalt

DeWalt DPN9033SM-XJ Útmutató

2 Szeptember 2024
DeWalt

DeWalt DC617 Útmutató

2 Szeptember 2024
DeWalt

DeWalt DC619 Útmutató

2 Szeptember 2024
DeWalt

DeWalt DMF1550 Útmutató

2 Szeptember 2024
DeWalt

DeWalt DPN46RN-XJ Útmutató

2 Szeptember 2024
DeWalt

DeWalt DPSB2IN1-XJ Útmutató

2 Szeptember 2024
DeWalt

DeWalt DPN1564A Útmutató

2 Szeptember 2024
DeWalt

DeWalt DPN1850 Útmutató

2 Szeptember 2024
DeWalt

DeWalt DWHT75021 Útmutató

1 Szeptember 2024

Útmutatók tűzőgép

Legújabb útmutatók tűzőgép

Einhell

Einhell BT-EN 30 E Útmutató

16 Január 2025
Total

Total TCBNLI2001 Útmutató

17 December 2024
Whirlpool

Whirlpool YWEE515S0LB Útmutató

9 December 2024
Whirlpool

Whirlpool YWEE515S0LV Útmutató

9 December 2024
Sun Joe

Sun Joe BDL-A0202 Útmutató

7 December 2024
MSW

MSW -STAPLER 1500 Útmutató

15 Október 2024
Makita

Makita AT638 Útmutató

2 Október 2024
Parkside

Parkside PET 25 B1 Útmutató

23 Szeptember 2024
Makita

Makita AN510H Útmutató

12 Szeptember 2024
Rexel

Rexel Optima Grip Útmutató

3 Szeptember 2024