Használati útmutató DeWalt DW735X

DeWalt gyalugép DW735X

Olvassa el alább 📖 a magyar nyelvű használati útmutatót DeWalt DW735X (48 oldal) a gyalugép kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/48

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D WALTe

Instruction Manual

Guide D’utilisation

Manual de instrucciones

DW735

13" (325 mm) Heavy-Duty Portable Thickness Planer

Raboteuse portative à service intensif 325 mm (13 po)

Cepilladora Portátil para Trabajo Pesado de 325 mm (13")

final page size: 8.5 x 5.5 in

English

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 15

Español (traducido de las instrucciones originales) 30

ENGLISH

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.



DANGER: will Indicates an imminently hazardous situation which, if not avoided, result in death or seriousinjury.

WARNING: could Indicates a potentially hazardous situation which, if not avoided, result in death or seriousinjury.

CAUTION: may Indicates a potentially hazardous situation which, if not avoided, result in minor or moderateinjury.

(Used without word) Indicates a safety related message.

NOTICE: may propertydamage Indicates a practice which, if not avoided, not related to personal injury result in .

WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

If you have any questions or comments about this or

any

D WALTe

tool, call us toll free at:

1-800-4-

D WALTe

(1-800-433-9258).

1 Planer

2 Side carrying handles

3 Base handles

4 Bench mounting holes

5 Crank handle

6 On/off switch

Fig. A

ENGLISH

General Power Tool Safety Warnings



WARNING: Read all safety warnings,

instructions, illustrations and specifications

provided with this power tool. Failure to follow all

instructions listed below may result in electric shock,

fire and/or seriousinjury.

SAVE ALL WARNINGS AND

INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) powertool.

General Safety Instructions

1 . KEEP GUARDS IN PLACE and in working order.

2 . REMOVE ADJUSTING KEYS AND WRENCHES. Form

habit of checking to see that keys and adjusting wrenches

are removed from tool before turning it on.

3 . KEEP WORK AREA CLEAN. Cluttered areas and benches

invite injuries.

4 . DON’T USE IN DANGEROUS ENVIRONMENT. t Don’

use power tools in damp or wet locations, or expose them

to rain. Keep work area well lighted. Always operate tool

in a well-ventilated area free of combustible materials,

gasoline or solvent vapors. If sparks come in contact

with flammable vapors, they may ignite, causing fire

orexplosion.

5 . KEEP CHILDREN AWAY. All visitors should be kept safe

distance from work area.

6 . MAKE WORKSHOP KID PROOF with padlocks, master

switches, or by removing starter keys.

7 . DON’T FORCE TOOL. It will do the job better and safer at

the rate for which it was designed.

8 . USE RIGHT TOOL. Don’t force tool or attachment to do a

job for which it was not designed.

9 . USE PROPER EXTENSION CORD. Make sure your

extension cord is in good condition. When using an

extension cord, be sure to use one heavy enough to carry

the current your product will draw. An undersized cord

will cause a drop in line voltage resulting in overheating

and loss of power. The Minimum Gauge for Cord Sets

table shows the correct size to use depending on cord

length and nameplate ampere rating. If in doubt, use the

next heavier gauge. The smaller the gauge number, the

heavier the cord. When operating a power tool outside,

use an outdoor extension cord marked “W-A” or “W.”

These cords are rated for outdoor use and reduce the risk

of electric shock.

10 . WEAR PROPER APPAREL. Do not wear loose clothing,

gloves, neckties, rings, bracelets, or other jewelry which

may get caught in moving parts. Nonslip footwear is

recommended. Wear protective hair covering to contain

long hair. Air vents often cover moving parts and should

also be avoided.

11 . ALWAYS USE SAFETY GLASSES. Also use face or

dust mask if cutting operation is dusty. Everyday

eyeglasses only have impact resistant lenses, they are not

safetyglasses.

12 . SECURE WORK. Use of clamps or a vise to hold work

when practical. It’s safer than using your hands and it

frees both hands to operate tool.

13 . DON’T OVERREACH. Keep proper footing and balance

at all times.

14 . MAINTAIN TOOLS WITH CARE. Keep tools sharp and

clean for best and safest performance. Follow instructions

for lubricating and changing accessories.

15 . DISCONNECT TOOLS before servicing; when changing

accessories, such as blades, bits, cutters, and the like.

16 . REDUCE THE RISK OF UNINTENTIONAL STARTING.

Make sure switch is in off position before plugging in.

17 . USE RECOMMENDED ACCESSORIES. Consult the

instruction manual for recommended accessories. The use

of improper accessories may cause risk of injury to persons.

18 . NEVER STAND ON TOOL. Serious injury could

occur if the tool is tipped or if the cutting tool is

unintentionallycontacted.

19 . CHECK DAMAGED PARTS. Before further use of the tool,

a guard or other part that is damaged should be carefully

checked to determine that it will operate properly and

perform its intended function—check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting, and any other conditions that may affect its

operation. A guard or other part that is damaged should

be properly repaired or replaced.

20 . DIRECTION OF FEED. Feed work into planer according to

direction of feed arrows on top of the unit.

21 . NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don’t leave tool until it comes to a

completestop.

Safety Rules for Surface Planers

WARNING: Failure to follow these rules may

result in serious personalinjury.

1 . Do not operate this machine until it is completely

assembled and installed according to the

instructions. A machine incorrectly assembled can cause

seriousinjury.

2 . Obtain advice from your supervisor, instructor, or

another qualified person if you are not thoroughly

familiar with the operation of this machine.

Knowledge issafety.

3 . Follow all wiring codes and recommended electrical

connections to prevent shock orelectrocution.

4 . Keep knives sharp and free from rust and pitch. Dull

or rusted knives work harder and can causekickback.

5 . Never turn the machine "ON" before clearing the

table of all objects (tools, scraps of wood, etc.). Flying

debris can cause seriousinjury.

6 . Never turn the machine "ON" with the workpiece

contacting the cutterhead. Kickback canoccur.

7 . Secure the machine to a supporting surface to

prevent the machine from sliding, walking or

tippingover.

8 . Be sure that the cutter knives are mounted as

described in the instruction manual and check that

ENGLISH

Additional Safety Information

WARNING: Never modify the power tool or any part

of it. Damage or personal injury couldresult.

WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.

WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-

treatedlumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are

specially designed to filter out microscopicparticles.

all bolts are firmly tightened before connecting unit

to powersource.

9 . Avoid awkward operations and hand positions. A

sudden slip could cause a hand to move into theknives.

10 . Keep arms, hands, and fingers away from the

cutterhead, the chip exhaust opening, and the feed

rollers to prevent severecuts.

11 . Never reach into the cutterhead area while the

machine is running. Your hands can be drawn into

theknives.

12 . Do not stand in line with the workpiece. Kickback can

causeinjury.

13 . Allow the cutterhead to reach full speed before

feeding a workpiece. Changing speeds while planing

can causekickback.

14 . When planing bowed stock, place the concave (cup

down) side of the stock on the table and cut with the

grain to preventkickback.

15 . Do not feed a workpiece that is warped, contains

knots, or is embedded with foreign objects (nails,

staples, etc.). Kickback canoccur.

16 . Do not feed a short, thin, or narrow workpiece into

the machine. Your hands can be drawn into the

knives and/or the workpiece can be thrown at high

speeds. See the Operation section of this instruction

manual fordetails.

17 . Do not feed a workpiece into the outfeed end of

the machine. The workpiece will be thrown out of the

opposite side at highspeeds.

18 . Remove shavings only with the power "OFF" and the

cutterhead stopped to prevent seriousinjury.

19 . Properly support long or wide work pieces. Loss of

control of the workpiece can cause seriousinjury.

20 . Never perform layout, assembly or set-up work on

the table/ area when the machine is running.work

Serious injury willresult.

21 . Turn the machine "OFF", disconnect it from the

power source, and clean the table/work area before

leaving the machine. Lock the switch in the "OFF"

position to prevent unauthorized use. Someone else

might accidentally start the machine and cause injury to

themselves orothers.

22 . Additional information regarding the safe and

proper operation of power tools (i.e. a safety

video) is available from the Power Tool Institute,

1300 Sumner Avenue, Cleveland, OH 44115-2851

(www.powertoolinstitute.com). Information is also

available from the National Safety Council, 1121 Spring

Lake Drive, Itasca, IL 60143-3201. Please refer to the

American National Standards Institute ANSI 01.1 Safety

Requirements for Woodworking Machines and the U.S.

Department of LaborRegulations.

Supplemental Safety Rules for Planers

• To avoid injury, never rotate the cutterhead directly with

yourhands.

• Keep hands away from the underside of the

cutterheadcarriage.

• Never clear clogs, make cutter knife replacement, or any

other repairs/adjustments with unit pluggedin.

• Make certain that the switch is in the "OFF" position

before connecting plug to a powersource.

• Stay alert—never operate the unit when tired or under the

influence of drugs, alcohol, ormedication.

• Do not use in dangerous environments. Do not use near

flammable substances, in damp or wet locations, or

expose torain.

• Never plane material which is shorter than 12" (304.8mm)

narrower than 3/4" (19.05 mm), or wider than 12"

(304.8mm) or thinner than 1/2" (12.7 mm).

• Exhaust chute: remove shavings with brush or vacuum

after power has been shut off and cutterhead has

stopped rotating.

• Always locate planer with proper clearance on the outfeed

side of the unit to prevent pinching or binding of the

workpiece against anyobstacle.

• Maintain the proper relationships of infeed and outfeed

table surfaces and cutterhead knifepath.

• Lock the speed setting securely before feeding the

workpiece through the machine. Changing speeds while

planing can causekickback.

English

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and

wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmfulchemicals.

WARNING: Use of this tool can generate and/

or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use

NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles

away from face andbody.

WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearingloss.

Power onnections C

A separate electrical circuit should be used for your

machines. This circuit should not be less than #12 wire

and should be protected with a 20 Amp time lag fuse.

nOTE: Time delay fuses should be marked “D” in Canada

and “T” in the US. If an extension cord is used, use only

3-wire extension cords which have 3-prong grounding

type plugs and matching receptacle which will accept the

machine’s plug. Before connecting the machine to the

power line, make sure the switch (or switches) is in the

"OFF" position and be sure that the electric current is of the

same characteristics as indicated on the machine. All line

connections should make good contact. Running on low

voltage will damage themachine.

DANGER: Do not expose the machine to rain or

operate the machine in damp locations.

MOTOR SPECIFICATIONS

Your machine is wired for 120 Volts, 60 HZ alternating

current. Before connecting the machine to the power

source, make sure the switch is in the "OFF" position.

Grounding Instructions

DANGER: This machine must be grounded while in

use to protect the operator from electricshock.

1 . All grounded, cord-connected machines:

ʵ In the event of a malfunction or breakdown,

grounding provides a path of least resistance for

electric current to reduce the risk of electric shock. This

machine is equipped with an electric cord having an

equipment-grounding conductor and a grounding

plug. The plug must be plugged into a matching

outlet that is properly installed and grounded in

accordance with all local codes andordinances.

ʵ Do not modify the plug provided - if it will not fit

the outlet, have the proper outlet installed by a

qualifiedelectrician.

ʵ Improper connection of the equipment-grounding

conductor can result in risk of electric shock. The

conductor with insulation having an outer surface

that is green with or without yellow stripes is the

equipment-grounding conductor. If repair or

replacement of the electric cord or plug is necessary,

do not connect the equipment-grounding conductor

to a liveterminal.

ʵ Check with a qualified electrician or service personnel

if the grounding instructions are not completely

understood, or if in doubt as to whether the machine

is properlygrounded.

ʵ Use only 3-wire extension cords that have 3-prong

grounding type plugs and matching 3-conductor

receptacles that accept the machine’splug.

ʵ Repair or replace damaged or worn cordimmediately.

2 . Grounded, cord-connected machines intended for use on

a supply circuit having a nominal rating less than

150 Volts:

ʵ This tool is intended for use on a circuit that has an

outlet that looks like the one illustrated in Fig. B. The

tool has a grounding plug that looks like the plug

illustrated in Fig. B. A temporary adapter, which looks

like the adapter illustrated in Fig. C, may be used to

connect this plug to a 2-pole receptacle as shown in

Fig B if a properly grounded outlet is not available.

The temporary adapter should be used only until

a properly grounded outlet can be installed by a

qualified electrician. The green-colored rigid ear, lug,

and the like, extending from the adapter must be

connected to a permanent ground such as a properly

grounded outletbox.

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDING BLADE

IS LONGEST OF THE 3 BLADES

Fig. B

GROUNDED OUTLET BOX

GROUNDING MEANS

ADAPTER

Fig. C

nOTE: In Canada, the use of a temporary adapter is not

permitted by the Canadian ElectricCode.

DANGER: In all cases, make certain that the

receptacle in question is properly grounded. If you

are not sure, have a qualified electrician check

thereceptacle.

ENGLISH

EXTENSION CORDS



WARNING: Use proper extension cords. Make sure

your extension cord is in good condition and is a

3-wire extension cord which has a 3-prong grounding

type plug and matching receptacle which will accept

the machine’s plug. When using an extension cord,

be sure to use one heavy enough to carry the current

of the machine. An undersized cord will cause a

drop in line voltage, resulting in loss of power and

overheating. Minimum Gauge for Cord Sets

shows the correct gauge to use depending on the cord

length. If in doubt, use the next heavier gauge. The

smaller the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet

(meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

V ......................... volts

Hz hertz .......................

min minutes .....................

or DC direct current ......

...................... Class I Construction

(grounded)

…/min .............. per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

or AC alternating current ...........

or AC/DC .... alternating or

direct current

...................... Class II

Construction

(double insulated)

no ....................... no load speed

n ......................... rated speed

...................... earthing terminal

..................... safety alert symbol

..................... visible radiation

..................... wear respiratory

protection

..................... wear eye

protection

..................... wear hearing

protection

..................... read all

documentation

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

Specifications

Input 120V AC, 15 Amp

No-load speed 10000 RPM

Feed speed 14' (4.3 m) or 26' (7.9 m) per minute

Planing height Maximum 6" (152.4 mm)

Minimum 1/8" (3.2 mm)

Planing width Maximum 13" (325 mm)

Planing depth Maximum 1/8" (3.2 mm) (for boards 6" [152 mm]

wide or less)

Electrical Connection

Be sure your power supply agrees with the nameplate

marking. Volts, 50/60 Hz or “AC only” means your planer

must be operated only with alternating current and never

with direct current. Voltage decrease of more than 10%

will cause loss of power and overheating. All

D WALTe

tools

are factory tested, if this tool does not operate, check the

powersupply.

Intended Use

This planer is designed for professional woodworking.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

Fan-Assisted Chip Ejection System

Your planer is equipped with a fan-assisted chip ejection

system to aid in exhausting chips from the unit. The fan-

assisted chip ejection system will work in conjunction with

independent dust collectionsystems.

NOTE: It is not recommended that a shop vac be

connected to the DW735. The capacity of most vacs does

not support the volume of chips ejected during planing.

The vacuum hose may clog stopping the flow of chips. It is

recommended to use the dust collection system to clean

debris from the interior of thetool.

See the , for additionalinformation.Troubleshooting Guide

Automatic Carriage Lock

There is no manual carriage lock on your planer. A

device that automatically minimizes the movement that

causes snipe during planing is designed into the four

threadedposts.

ASSEMBLY AND ADJUSTMENTS

WARNING: Do not remove guards (7, Fig.D).

Serious injury couldresult.

Fig. D

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from

power source before making any adjustments or

removing/installing attachments or accessories.

An accidental start-up can causeinjury.

English

Transporting the Planer (Fig. A)



WARNING: For your own safety, it is recommended

that two people carry this machine or serious injury

couldresult.

When moving your planer, carry it either by the side

carrying handles2 or by the handles3at the base of

theplaner.

Bench Mounting (Fig. A)

To facilitate bench mounting, two different sized holes 4

are provided on the four corners of your planer. If mounting

the planer with bolts, use the larger holes. If mounting the

planer with nails or screws, use the smaller holes. It is not

necessary to use both sets ofholes.

Always mount your planer firmly to prevent movement. To

enhance the tool’s portability, it can be mounted to a piece

of 1/2" (12.7mm) or thicker plywood which can then be

clamped to your work support or moved to other job sites

andreclamped.

nOTE: If you elect to mount your planer onto a piece

of plywood, make sure that the mounting screws don’t

protrude from the bottom of the wood. The plywood must

sit flush on the worksupport.

CAUTION: The mounting surface should not be

warped or otherwiseuneven.

To Attach the Depth Adjustment Crank

Handle (Fig. E)

1. Remove the screw located in the crank handleshaft.

2. Insert the crank handle5 over theshaft.

3. Secure in place with the screw and

T-wrench8provided.

Fig. E

Dust Ejection Ports (Fig. F)

Your planer comes with a dust ejection port. The round

port9 as shown in Figure. F is for use with a 4" (100mm)

dust collectorhose.

To Set Up Dust Ejection (Fig. F)

WARNING: Do not operate your planer without

the dust ejection port locked into place. Do not

insert anything into the dust ejection chute

unless the planer is unplugged and you are

clearing a clog or obstruction in the unit. Do not

get your face or eyes near the dust ejection port

when the planer is in operation. Serious injury

couldresult.



WARNING: Chips are ejected at significant velocity.

Keep hands and face clear of dust ejectionport.

1. Select the port9.

2. Depress the lock button11 on the chip ejection

chute10.

Fig. F

3. Slide the notches in the dust port over the pins on the

chip ejectionchute.

4. Rotate the port until the button engages the dust

ejection chute and locks inplace.

To Remove the Dust Ejection Port

(Fig. F)

1. Use the T-wrench to depress the lock button 11 on the

dustchute.

2. Twist the port until the pins are disengaged from the

notches on theport.

3. Pull the dust ejection port off of the dustchute.

Depth Adjustment (Fig. G)

Depth Adjustment Scale (Fig. G)

The depth adjustment scale14, located on the right front

of your planer, indicates the finished thickness of your

workpiece. One rotation of the depth adjustment crank

is equal to 1/16" (1.6mm), half rotation is equal to 1/32"

(0.8mm),etc.

Fig.G

ENGLISH



WARNING: DO NOT switch the unit on with the

material positioned under the carriage. Serious

injury couldresult.

Planing Basics

Proper Planing Technique

WARNING: DO NOT turn the unit on with the

material already inserted under the carriage.

Wait until the rollers and cutterhead are up to

full speed before feeding your material into

themachine.

To Plane Your Material

1. Lower the carriage to the desired height for your

firstpass.

2. Turn the unit on and feed the material into the

feedrollers.

3. Examine the finished cut and adjust the carriage to the

appropriate height for your nextpass.

NOTE: Flip the board back and forth between eachpass.

See the , for additionalinformation.Troubleshooting Guide

For best results, plane both sides of the workpiece to reach

a desired thickness. For example, if you need to remove 1/8"

(3mm) from your workpiece, remove 1/16" (1.6mm) from

each side. This not only allows the workpiece to dry with an

even moisture content, it also produces finercuts.

WARNING: Plane only wood that is free from foreign

objects, with no loose knots and as few tight knots as

possible. Do not plane wood that is severely warped,

twisted, knotted orbowed.

WARNING: Do not place your body between the rear

of the planer and a stationary object while material is

feeding. Serious injury couldresult.

Minimum/Maximum Width/

Height/ Depth

NOTE: Always plane in the direction of the grain. Support

the workpiece adequately at all times. Planing material less

than 3/4" (19mm) wide is not recommended. If you must

plane narrow material, group several pieces together and

plane them as one wide workpiece wheneverpossible.

The maximum depth of cut your planer can take in one pass

is 1/8" (3mm) [on material less than 6" (152 mm) wide].

Never attempt to modify your planer to take a deeper cut.

Follow the recommended depth/width of cut guidelines

shown in Table A for bestresults.

TABLE A

Snipe

Snipe is a depression made when an unsupported end of

your material drops toward the floor, causing the opposite

end to lift up into thecutterhead.

To Avoid Snipe

Feed the workpiece into the planer so it is level and remains

flat against the base at alltimes.

Keep the workpiece level throughout planing operation by

receiving or “catching” it from the rear of theplaner.

If you are planing material that is especially long, the use of

additional material support isrecommended.

Twisted, Cupped and Bowed Wood (Fig. L)

If both sides of your material are very rough or if the material

is cupped, bowed or twisted, your planer may not produce

the desired result. Ideally, you should have at least one

level face/surface on your material before you plane. Your

thickness planer will work best with material that has been

run through a jointer to produce one flat surface. If you

do not have at least one flat surface or a jointer, see the

followingrecommendations.

Fig.L

To Plane Twisted Wood (Fig. M)

WARNING: Twisted wood may jam your

thickness planer. If a jam occurs, turn the

power off, disconnect the power supply and

raise the carriage to release the material from

thecutterhead.

If your material is only slightly twisted:

Plane both sides alternating from one to the other until the

desired thickness isreached.

Fig.M

To Plane Cupped Wood (Fig. N)

To obtain the best possible results with cupped wood:

Rip the material down the middle and plane it as two

separatepieces.

Ripping the material reduces the severity of the cup and

allows the machine to deliver better results. Understand

that you will have to remove more material on cupped

wood to achieve the desired thickness than you would on a

normalboard.

If Ripping the Material is Not an Option

Plane one side of the material until flat, then plane the

opposite side until it is alsoflat.

NOTE: Do not flip the board back and forth between each

pass if wood iscupped.

English

TOP FlAT

BOTTOM FlAT

Fig.N

To Plane Bowed Wood (Fig. O)

The feed rollers and cutterhead in your planer will push

the bow out of the material as it feeds. However, when the

material exits the planer, the pressure of the rollers and

cutterhead will release allowing the wood to spring back

into a bowed formation. To properly remove the bow, use

ajointer.

BOWED WOOD Will BE FlATTEnED BY FEED ROllERs

AnD CUTTERhEAD…

…BUT BOW Will RETURn AFTER WOOD

isPlAnED

Fig.O

MAINTENANCE

WARNING: To reduce the risk of serious personal

injury, turn unit off and disconnect it from

power source before making any adjustments or

removing/installing attachments or accessories.

An accidental start-up can causeinjury.

Periodic Maintenance

1. Routinely check the tool for damage or brokenparts.

2. Clean the top cover, dust shroud and all accessible areas

of the unit of dust and wood debris that have collected

in fromplaneing.

3. Wipe off infeed and outfeedrollers.

4. Clean base table. Light waxing will help wood material

pass through theplaner.

5. Evaluate blade sharpness condition. Replace

asnecessary.

6. Gauge Calibration, check thickness gauge calibration

and turret stopcalibration.

7. Check brushes for wear and replace asnecessary.

Changing or Rotating the Planer Knives

WARNING: To reduce the risk of serious personal

injury, disconnect the planer from the power

source before attempting to change or access the

knives. An accidental start-up can causeinjury.

To Change Planer Knives (Fig. P–U)

1. Use the T-wrench to remove the four screws in the top

of theplaner.

2. Lift the top off (Fig.P) and place itaside.

Fig.P

3. Remove the three wing nuts that seal the dust shroud

over thecutterhead.

4. Rotate the dust shroud up so the round connection

that locks onto the fan housing is in the open position

(Fig.Q).

Fig.Q

5. Push the dust shroud to the left so it disengages from

the fanhousing.

6. Take the dust shroud out of the unit (Fig.R) and set

itaside.

Fig.R

7. The cutterhead is nowexposed. If the eight screws in

the cutterhead clamp are not visible, use a piece of

scrap wood to carefully rotate the cutterhead (Fig.S)

until the screws are accessible and the cutterhead lock

lever18 engages. This will prevent further rotation of

the cutterhead as you change theknives.

English

Fig.S

WARNING: Keep your fingers away from the

cutterhead at all times. Use the tool provided to

handle theknives.

8. Use the T-wrench to remove the eight screws on the

knife clamp and set them in the small screws bin 19 on

the front panel of the planer (Fig.T).

Fig.T

9. Use the magnets on the top of the T-wrench to attract

the knife clamp and lift it off of the cutterhead. One of

the knives should now beexposed.

10. Use the magnet20 on the top of the T-wrench (Fig.S)

to attract the knife. Avoid touching it with yourfingers.

nOTE: Before installing the knife, ensure the cutterhead and

knife are free of debris, clean if needed.

Fig.U

If Only One Side of the Knife Is Worn

1. Rotate the knife around so that the sharp, unused edge

hangs over the end of the cutterhead where it will cut

the material. Be sure to set the oblong holes in the knife

over the pins machined on thecutterhead.

2. Reset the knife clamp over the knife. Be sure to align the

beveled edge on the clamp with the sharp, cutting edge

of the knife. If these are not aligned correctly, the clamp

will not secure the knifeproperly.

3. Install the screws into the clamp and tightensufficiently.

nOTE: Make sure all screws are tightenedsufficiently.

To Access the Other Two Knives

1. Depress the cutterhead lock lever18 as shown in

FigureS.

2. Use the piece of scrap wood to carefully turn the

cutterhead until it locks into place revealing another

knifeclamp.

3. Follow the same knife change procedure

indicatedabove.

4. Repeat the procedure for the last dullknife.

After Installing New Knives

1. Insert the round end of the dust shroud into the fan

housing and rotate it down to lock it intoplace.

2. Place the three wing nuts back into theshroud.

3. Screw the top cover of the planer back onto theunit.

nOTE: The planer will not operate if the top cover is not

placedcorrectly.

Brush Change (Fig. V, W)

Your planer is equipped with brush caps 21 that are

external to the motor. If your brushes need to be replaced,

begin by acquiring a new set from a

D WALTe

service center

or a dealer authorized to service

D WALTe

products. Use only

identical

D WALTe

brushes.

Fig.V

To Replace the Brushes on your Planer

(Fig. V, W)

1. Use the T-wrench to remove the top cover and brush

cover screen on theplaner.

2. Use a flathead screwdriver to unscrew the brush cap

located in the right, rear of the unit22.

Fig.W

3. Do the same for the brush cap located on the side of the

motor, inside the planercover.

4. Place the new brushes into the brushholders.

English

5. After installing the brushes, replace the top cover and

brush coverscreen.

6. Before using the planer, run the unit for 10 minutes to

seat newbrushes.

nOTE: If existing brushes do not need replacing, be sure to

maintain the same orientation when you reinstallthem.

Calibrating the Depth Adjustment Scale

(Fig. X)

The depth adjustment scale14 on your planer is set at the

factory. However, with extended use, the depth adjustment

scale could show an incorrectmeasurement.

To check the depth adjustment scale, plane a piece of

scrap wood, noting the measurement on the depth

adjustmentscale.

Measure the finished thickness of the workpiece. If the

thickness of the workpiece does not match the reading on

the depth adjustment scale, loosen the two screws23 on

the red indicator. Adjust the pointer up or down until its

reading matches the finished thickness of the workpiece.

Securely re-tighten thescrews.

Fig.X

Base Maintenance

Keep the table clean and free from oil, grease, and pitch.

Treat the table with paste wax to help maintain its

smoothfinish.

Circuit Breaker Reset Button (Fig. Y)

Your planer is equipped with an 18 amp circuit breaker. If

your planer becomes overloaded and stops operating, turn

off the planer, let the unit sit for 2 minutes and press the

reset button24 before you resumeworking.

Fig.Y

WARNING: To prevent the planer from starting

unexpectedly if power is interrupted by a circuit

breaker trip, make sure the switch is in the OFF

position before restoringpower.

nOTE: Circuit breaker overload is often the result of dull

knives. Change your knives on a regular basis to avoid

tripping your breaker. Check your knives before re-setting

the circuit breaker and continuing toplane.

See the for additional information Troubleshooting Guide

on circuit breakertrips.

Replacing the Drive Belt

Drive belts are available at extra cost at

D WALTe

authorized

service centers. Replacement of the drive belt should be

performed by qualified servicepersonnel.

Chip Ejection Fan (Fig. P–R, Z)

The chip ejection fan on your planer should

be cleaned or cleared of debrisperiodically.

Fig.Z

WARNING: Turn off and unplug the planer prior to

accessing the chip ejectionfan.

To Access the Fan

1. Remove the top cover of the planer with the T-wrench.

2. Remove the dust shroud (Fig.P–R) and place itaside.

3. Remove the screws and clips around the fanhousing.

4. Remove the fan housing and place it aside as shown.

The fan will now be exposed forcleaning.

See the for additionalinformation. Troubleshooting Guide

WARNING: Be sure to properly attach the fan housing

and assemble the shroud and top cover correctly

before using your planeragain.

Cleaning

WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performingthisprocedure.

WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the plastic

materials used in these parts. Use a cloth dampened

only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool

into aliquid.

It is recommended that, once a year, you take or send the

tool to a

D WALTe

certified service center for a thorough

cleaning, inspection and lubrication of the gearcase.

Accessories

WARNING: Since accessories, other than those

offered by

D WALTe

, have not been tested with this

product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only

D WALTe

recommended accessories should be used with

thisproduct.

English

Recommended accessories for use with your tool

are available at extra cost from your local dealer or

authorized service center. If you need assistance in

locating any accessory, please contact

D WALTe

Industrial

Tool Co., 701East Joppa Road, Towson, MD 21286, call

1-800-4-

D WALTe

(1-800-433-9258) or visit our website:

www.dewalt.com.

Four accessories are available for the DW735

ThicknessPlaner.

• DW7350 Mobile Stand

• DW7351 Folding Tables

• DW7352 13" (325mm) Knives

• DW7353 Chip Ejection Accessory

nOTE: Helical cutterheads have not been tested with this

product and are not recommended foruse.

DW7351 Accessory Folding Tables (Fig. AA)

WARNING: For your own safety, read the tool

instruction manual before attaching the tables.

Failure to heed these warnings may result in personal

injury and serious damage to the planer and the

accessory. When servicing this tool, use only identical

replace ment parts. Have damaged cords replaced by

an authorized servicecenter.

Your DW7351 folding table box should include:

2 folding tables

4 cap screws

4 springs

4 nuts

4 stepped bolts

Fig.AA

Set-up and Installation of Base

Hardware (Fig. BB–DD)

1. Place planer on a secure table or workbench. Position

planer so the front 3–4" (75–100mm) of the base can

be accessed from theunderside.

2. Secure the rear of the planer to the table/bench with

nails or screws to prevent it from tilting or falling from

thetable.

WARNING: The planer could tilt or fall from the table

if it is not properly secured opposite the end where

the folding table is being installed. Serious injury

mayresult.

3. Place the spring onto the small end of the steppedbolt.

4. Insert the end of the bolt with the spring around it into

the larger hole on the side of thebase.

5. Push the stepped bolt all the way through the hole in

the first rib on the underside of the planer. The spring

should engage the rib slightly and the threads should

show on the right side of therib.

6. On the underside of the planer, use a wrench to hold

the nut in place while turning the stepped bolt into it.

The 5/32" (4 mm) hex wrench can be used to turn the

stepped bolt until it is fully secured (Fig.BB).

Fig.BB

7. Install the smaller screw into the lower threaded hole on

the side of the base. Use the 5/32" (4mm) hex wrench to

tighten that fastener securely (Fig.CC).

8. Depress the top pin until it is flush with the base and

slide the top hole of the table over the pin and release

the pin so they lock together (Fig.CC,DD).

Fig.CC

Fig.DD

9. To attach the table to the rear of the planer, install the

bolts and spring following the aboveprocedure.

Your tables should now fold up and down on the top screw

and rest on the bottom screw while in position forplaning.

nOTE: To transport the planer with the tables, fold them up

and carry the unit as recommended by the planermanual.

WARNING: For your own safety, it is recommended

that two people carry this machine or serious injury

couldresult.

To Remove the Tables

1. Depress the spring-loaded bolts on the base and slide

each end of the table toward you so they disengage the

holes in the tables. You may want to use the T-wrench

from your planer to push the bolts flush with the base to

easily remove thetables.

2. Leave the hardware (stepped bolts and small cap screw)

in the base until you need to re-attach thetables.

English

Repairs



WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement, when

applicable) should be performed by a

D WALTe

factory

service center or a

D WALTe

authorized service center.

Always use identical replacementparts.

Thank you for your purchase. Register your product nowfor:

• Registering your product will WARRAnTY sERViCE:

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• In case of COnFiRMATiOn OF OWnERshiP:

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• Registering your product will FOR YOUR sAFETY:

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

Three Year Limited Warranty

D WALTe

will repair, without charge, any defects due to

faulty materials or workmanship for three years from

the date of purchase. This warranty does not cover part

failure due to normal wear or tool abuse. For further detail

of warranty coverage and warranty repair information,

visit www.dewalt.com or call 1-800-4-

D WALTe

(1-800-

433-9258). This warranty does not apply to accessories

or damage caused where repairs have been made

or attempted by others. THIS LIMITED WARRANTY IS

GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED

WARRANTY OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states do not allow

limitations on how long an implied warranty lasts or the

exclusion or limitation of incidental or consequential

damages, so these limitations may not apply to you. This

warranty gives you specific legal rights and you may have

other rights which vary in certain states orprovinces.

In addition to the warranty,

D WALTe

tools are covered

byour:

1 YEAR FREE sERViCE

D WALTe

will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year

afterpurchase.

90 DAY MOnEY BACK gUARAnTEE

If you are not completely satisfied with the performance of

your

D WALTe

Power Tool, Laser, or Nailer for any reason, you

can return it within 90 days from the date of purchase with

a receipt for a full refund – no questionsasked.

lATin AMERiCA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARning lABEl REPlACEMEnT: If your warning

labels become illegible or are missing, call 1-800-4-

D WALTe

(1-800-433-9258) for a freereplacement.

ENGLISH

Troubleshooting Guide

Problem Possible Cause Possible Solution

If the material does not feed properly Check for dull knives. Rotate or replace as necessary. Refer to Changing the Planer

Knives section.

Check for excess clogging in the

dust shroud.

Refer to and Figures P–R in the Periodic Maintenance Changing

or Rotating the Planer Knives section.

Check for excess oil/debris/pitch on

feed rollers.

Refer to paragraphs under Periodic Maintenance and Cleaning

the Maintenance section.

Check for excessively twisted, cupped

or bowed material.

Refer to paragraph in the Twisted, Cupped and Bowed Wood

Basic Planing section.

Check for a broken drive belt. Refer to paragraph in the Replacing the Drive Belt

Maintenance section.

If the circuit breaker trips repeatedly Dull knives Dull knives can cause motor overloading, rotate or replace as

necessary. Refer to section.Changing the Planer Knives

NOTE: Circuit breaker overload is often the result of dull knives.

If the circuit breaker on your planer trips, check the sharpness

of your knives before attempting to reset the breaker in order to

continue planing.

The depth of cut is higher. An overly aggressive cut could cause motor overloading. Refer

to the paragraph in the Depth Adjustment Assembly and

Adjustments section and paragraph Material Removal Gauge

in the section.Operation

The feed rate is higher. Drop feed rate to 14 ft/min. A reduction in feed rate will reduce the

load on the motor and prevent breaker trips.

If the unit does not run Check to see if the unit is plugged in. Ensure unit is plugged into the appropriate outlet, refer to the

General Safety Instructions section.

Check to see if the top cover is

properly in place.

Refer to Figure P for proper location.

Check to see if the dust shroud is

properly in place.

Refer to After Installing New Knives.

Check to see if the circuit breaker

needs to be reset.

Refer to paragraph under the Circuit Breaker Reset Button

Maintenance section.

Check to see if the motor brushes

are depleted.

Refer to paragraph under the section. Brushes Maintenance

If chips do not eject from the rear of

the unit

Check for excess clogging in the

dust shroud and fan..

Refer to and Periodic Maintenance Chip Ejection Fan

paragraphs in the section.Maintenance

Check to see if the dust shroud is

properly in place.

Refer to After Installing New Knives.

If the branch (house/shop) circuit

breaker trips repeatedly

Even under normal loading conditions,

other electrical loads on the same

branch circuit may cause the circuit

breaker to trip.

Unplug or turn off other devices sharing the circuit with the planer

OR use the planer on another branch circuit by itself.

Dull knives Dull knives can cause motor overloading, rotate or replace as

necessary. Refer to section.Changing the Planer Knives

The depth of cut is higher. An overly aggressive cut could cause motor overloading. Refer

to the paragraph in the Depth Adjustment Assembly and

Adjustments section and paragraph Material Removal Gauge

in the section.Operation

The feed rate is higher. Drop feed rate to 14 ft/min. A reduction in feed rate will reduce the

load on the motor and prevent breaker trips.

Termékspecifikációk

Márka:	DeWalt
Kategória:	gyalugép
Modell:	DW735X

Szüksége van segítségre?

Ha segítségre van szüksége DeWalt DW735X, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók gyalugép DeWalt

DeWalt DCP580 Útmutató

21 Augusztus 2024

DeWalt DW735 Útmutató

29 Július 2024

DeWalt DW680K Útmutató

25 Július 2024

DeWalt D26677K Útmutató

21 Július 2024

DeWalt DW735X Útmutató

17 Július 2024

DeWalt DW682 Útmutató

16 Július 2024

DeWalt DW733 Útmutató

13 Július 2024

DeWalt DW678 T 3 Útmutató

3 Július 2024

DeWalt D26500 Útmutató

3 Július 2024

DeWalt DW678E T 2 Útmutató

30 Június 2024

Útmutatók gyalugép

Legújabb útmutatók gyalugép

Einhell EHM 1300 Útmutató

5 December 2024

Einhell RT-SP 260 D Útmutató

5 December 2024

Protool PLP 24 Útmutató

20 Szeptember 2024

HiKOKI P20SFWAZ Útmutató

16 Szeptember 2024

Einhell Expert TE-PL 18/82 Li Útmutató

5 Szeptember 2024

Einhell TC-PL 900 Útmutató

5 Szeptember 2024

Einhell RTB-003 Útmutató

5 Szeptember 2024

Einhell LOF 850 E Útmutató

5 Szeptember 2024

Einhell E-HO 900 Útmutató

2 Szeptember 2024

Einhell E-OF 1200 Útmutató

2 Szeptember 2024