Használati útmutató DeWalt DCD960
Olvassa el alább 📖 a magyar nyelvű használati útmutatót DeWalt DCD960 (7 oldal) a fúrógép kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/7
INSTRUCTION MANUAL
GUIDE D’UTILISATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES
DE USAR EL PRODUCTO.
DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286
(OCT08) Part No. 658870-00 DCD910, etc. Copyright © 2008 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme;
the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the
array of lozenge-shaped humps on the surface of the tool.
DCD910, DCD920, DCD940, DCD960 Heavy-Duty 1/2 (13 mm) Cordless Drill/Driver "
DCD930, DCD950, DCD970 Heavy-Duty 1/2 (13 mm) Cordless Hammerdrill/Drill/Drivers"
Perceuses/Visseuses industrielles sans fil 13 mm (1/2 po) DCD910, DCD920, DCD940, DCD960
Marteaux perforateurs/Perceuses/Visseuses industriels sans fil 13 mm (1/2 po) DCD930, DCD950, DCD970
Taladro / destornillador inalámbrico de 1/2 pulg. (13 mm) para trabajos pesados DCD910, DCD920, DCD940, DCD960
Taladro percusor / taladro / destornillador inalámbrico de 1/2 pulg. (13 mm) para trabajos pesados DCD930, DCD950, DCD970
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-D WALT • www.dewalt.comE
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read
the manual and pay attention to these symbols.
DANGER: will Indicates an imminently hazardous situation which, if not avoided,
result in death or serious injury.
WARNING: could Indicates a potentially hazardous situation which, if not avoided,
result in death or serious injury.
CAUTION: mayIndicates a potentially hazardous situation which, if not avoided,
result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous
situation which, if not avoided, result in may property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D WALT TOOL, E
CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258).
WARNING: To reduce the risk of injury, read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a ground fault
circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or
a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-
related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power
tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits, etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could
result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified by the manufacturer. A charger that is
suitable for one type of battery pack may create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects like paper
clips, coins, keys, nails, screws, or other small metal objects that can make a
connection from one terminal to another. Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Specific Safety Rules
• Wear ear protectors with impact drills. Exposure to noise can cause hearing loss.
• Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.
• Hold power tools by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring or its own cord. Contact with a “live”
wire will make exposed metal parts of the tool “live” and shock the operator.
• Use clamps or another practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body leaves it unstable and may lead to
loss of control.
• Wear ear protectors when hammering for extented periods of time. Prolonged exposure
to high intensity noise can cause hearing loss. Temporary hearing loss or serious ear drum
damage may result from high sound levels generated by hammer drilling.
• Wear safety goggles or other eye protection. Hammering and drilling operations cause
chips to fly. Flying particles can cause permanent eye damage.Wear a dust mask or respirator
for applications that generate dust. Ear protection may be required for most applications.
• Always use the side handle supplied with the tool. Keep a firm grip on the tool at all
times. Do not attempt to operate this tool without holding it with both hands. Operating
this tool with one hand will result in loss of control. Breaking through or encountering hard
materials such as re-bar may be hazardous as well.
• Accessories and tool may get hot during operation. Wear gloves when handling them if
performing heat producing applications such as hammerdrilling and drilling metals.
• Do not operate this tool for long periods of time. Vibration caused by hammer action may
be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure
by taking frequent rest periods.
• Air vents often cover moving parts and should be avoided. Loose clothes, jewellery or
long hair can be caught in moving parts.
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also
use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially designed to filter out microscopic
particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
other construction activities. Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body.
WARNING: Always wear proper personal hearing protection that conforms to ANSI
S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product
may contribute to hearing loss.
CAUTION: When not in use, place tool on its side on a stable surface where it will not
cause a tripping or falling hazard. Some tools with large battery packs will stand upright on
the battery pack but may be easily knocked over.
• The label on your tool may include the following symbols. The symbols and their definitions
are as follows:
V ......................volts A ......................amperes
Hz ....................hertz W .....................watts
min ..................minutes ................... alternating current
...............direct current ...................alternating or direct current
....................Class I Construction no .................... no load speed
........................(grounded) ....................earthing terminal
....................Class II Construction ....................safety alert symbol
........................(double insulated) BPM ................beats per minute
…/min .............per minute RPM ................revolutions per minute
IPM..................impacts per minute
Important Safety Instructions for All Battery Packs
When ordering replacement battery packs, be sure to include catalog number and voltage.
Consult the chart at the end of this manual for compatibility of chargers and battery packs.
The battery pack is not fully charged out of the carton. Before using the battery pack and
charger, read the safety instructions below. Then follow charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting or removing the battery from the charger may
ignite the dust or fumes.
• NEVER force battery pack into charger. DO NOT modify battery pack in any way
to fit into a non-compatible charger as battery pack may rupture causing serious
personal injury. Consult the chart at the end of this manual for compatibility of batteries and
chargers.
• Charge the battery packs only in DEWALT chargers.
• DO NOT splash or immerse in water or other liquids.
• Do not store or use the tool and battery pack in locations where the temperature may
reach or exceed 105°F (40˚C) (such as outside sheds or metal buildings in summer).
DANGER: Electrocution hazard. Never attempt to open the battery pack for any reason.
If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or
damage battery pack. Do not use a battery pack or charger that has received a sharp blow,
been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer,
stepped on). Electric shock or electrocution may result. Damaged battery packs should be
returned to service center for recycling.
NOTE: Battery storage and carrying caps are provided for use whenever the
battery is out of the tool or charger. Remove cap before placing battery in charger
or tool.
WARNING: Fire hazard. Do not store or carry battery so that metal
objects can contact exposed battery terminals. For example, do not place
battery in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws,
keys, etc. without battery cap. Transporting batteries can possibly cause fires if the battery
terminals inadvertently come in contact with conductive materials such as keys, coins,
hand tools and the like. The US Department of Transportation Hazardous Material Regulations
(HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e., packed in
suitcases and carry-on luggage) UNLESS they are properly protected from short circuits. So
when transporting individual batteries, make sure that the battery terminals are protected and
well insulated from materials that could contact them and cause a short circuit.
SPECIFIC SAFETY INSTRUCTIONS FOR NICKEL CADMIUM (NiCd) OR NICKEL METAL
HYDRIDE (NiMH)
• Do not incinerate the battery pack even if it is severely damaged or is completely worn
out. The battery pack can explode in a fire.
• A small leakage of liquid from the battery pack cells may occur under extreme usage
or temperature conditions. This does not indicate a failure.
However, if the outer seal is broken:
a. and the battery liquid gets on your skin, immediately wash with soap and water for several
minutes.
b. and the battery liquid gets into your eyes, flush them with clean water for a minimum of
10 minutes and seek immediate medical attention. ( The liquid is 25-35% Medical note:
solution of potassium hydroxide.)
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (LI-ION)
• Do not incinerate the battery pack even if it is severely damaged or is completely
worn out. The battery pack can explode in a fire. Toxic fumes and materials are created
when lithium ion battery packs are burned.
• If battery contents come into contact with the skin, immediately wash area with
mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is
composed of a mixture of liquid organic carbonates and lithium salts.
• Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If
symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.
The RBRC™ Seal
The RBRC™ (Rechargeable Battery Recycling Corp oration) Seal on the nickel
cadmium, nickel metal hydride or lithium ion batteries (or battery packs) indicate
that the costs to recycle these batteries (or battery packs) at the end of their useful
life have already been paid by DEWALT. In some areas, it is illegal to place spent
nickel cadmium, nickel metal hydride or lithium ion batteries in the trash or municipal solid waste
stream and the RBRC program provides an environmentally conscious alternative.
RBRC™ in cooperation with DEWALT and other battery users, has established programs in
the United States and Canada to facilitate the collection of spent nickel cadmium, nickel metal
hydride or lithium ion batteries. Help protect our environment and conserve natural resources
by returning the spent nickel cadmium and nickel cadmium, nickel metal hydride or lithium ion
batteries to an authorized DEWALT service center or to your local retailer for recycling. You may
also contact your local recycling cen tion on where to drop off the spent battery.ter for informa
RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation.
Important Safety Instructions for All Battery Chargers
SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions
for battery chargers.
• Before using charger, read all instructions and cautionary markings on charger, battery pack,
and product using battery pack.
DANGER: Electrocution hazard. 120 volts are present at charging terminals. Do not probe
with conductive objects. Electric shock or electrocution may result.
WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may
result.
CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT rechargeable
batteries. Other types of batteries may burst causing personal injury and damage.
CAUTION: Under certain conditions, with the charger plugged in to the power supply, the
exposed charging contacts inside the charger can be shorted by foreign material. Foreign
materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any
buildup of metallic particles should be kept away from charger cavities. Always unplug the
charger from the power supply when there is no battery pack in the cavity. Unplug charger
before attempting to clean.
• DO NOT attempt to charge the battery pack with any chargers other than the ones in
this manual. The charger and batter y pack are specifically designed to work together.
• These chargers are not intended for any uses other than charging DEWALT rechargeable
batteries. Any other uses may result in risk of fire, electric shock or electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when disconnecting charger. This will reduce risk of
damage to electric plug and cord.
• Make sure that cord is located so that it will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
• Do not use an extension cord unless it is absolutely necessary. Use of improper
extension cord could result in risk of fire, electric shock, or electrocution.
• When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
• An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that
is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. When using more than one extension to
Mode Control Collar (Fig. 2–4)
Your drill is equipped with a separate mode control collar (F) to switch between drilling,
screwdriving and hammerdrilling mode.
DRILLING (FIG. 2)
CAUTION: When the mode collar is in the drill/hammerdrill mode, the drill will not clutch out
regardless of the position of the torque adjustment collar (E).
Rotate the mode control collar (F) so the drill symbol is aligned with the arrow.
NOTE: The torque adjustment collar (E) may be set on any number.
SCREWDRIVING (FIG. 3)
Rotate the mode control collar (F) so the screw symbol is aligned with the arrow.
NOTE: The torque adjustment collar may be set to any number at any time. However, the torque
adjustment collar is only engaged during screwdriving mode and not in drill and hammerdrill
modes.
HAMMERDRILLING (FIG. 4)
CAUTION: When the mode collar is in the drill/hammerdrill mode, the drill will not clutch out
regardless of the position of the torque adjustment collar (E).
Rotate the mode control collar (F) so the hammer symbol is aligned with the arrow.
Torque Adjustment Collar (Fig. 2–4)
Your tool has an adjustable torque screwdriver mechanism for driving and removing a wide
array of fastener shapes and sizes. Circling the torque adjustment collar (E) are numbers. These
numbers are used to set the clutch to deliver a torque range. The higher the number on the
collar, the higher the torque and the larger the fastener which can be driven. To select any of
the numbers, rotate until the desired number aligns with the arrow.
Three-Speed Gearing (Fig. 2–4)
The three-speed feature of your tool allows you to shift gears for greater versatility. To select
speed 1 (highest torque setting), turn the tool off and permit it to stop. Slide the gear shifter (G)
all the way forward. Speed 2 (middle torque and speed setting) is in the middle position. Speed 3
(highest speed setting) is to the rear.
NOTE: Do not change gears when the tool is running. Always allow the drill to come to a complete
stop before changing gears. If you have trouble changing gears, make sure that the gear shifter is
engaged in one of the three speed settings.
Chucks
WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front
part of the chuck and turning the tool on. Damage to the chuck and personal injury may result.
Always lock off trigger switch and disconnect tool from power source when changing acces-
sories.
WARNING: Always ensure the bit is secure before starting the tool. A loose bit may eject
from tool causing possible personal injury.
KEYLESS SINGLE SLEEVE CHUCK (FIG. 5–7)
DCD910, DCD920, DCD940, DCD960
Your tool features a keyless chuck with one rotating sleeve for one-handed operation of the
chuck. To insert a drill bit or other accessory, follow these steps.
1. Lock the trigger in the OFF position. Turn off tool and disconnect tool from power source.
2. Grasp the black sleeve of the chuck (D) with one hand and use the other hand to secure the
tool as shown in Figure 5. Rotate the sleeve counterclockwise (as viewed from the front) far
enough to accept the desired accessory.
3. Insert the accessory about 3/4" (19 mm) into the chuck and tighten securely by rotating the
chuck sleeve clockwise with one hand while holding the tool with the other hand. Continue to
rotate the chuck sleeve until several ratchet clicks are heard to ensure full gripping power.
To release the accessory, repeat Steps 1 and 2 above.
Be sure to tighten chuck with one hand on the chuck sleeve and one hand holding the tool for
maximum tightness.
SELF-TIGHTENING CHUCK OPERATION (FIG. 8–10)
DCD930, DCD950, DCD970
To insert a drill bit or other accessory:
1. Lock the trigger in the OFF position. Turn off tool and disconnect tool from power source.
2. Grasp the chuck sleeve (I) with one hand and use the other hand to secure the tool as shown
in Figure 8. Rotate the sleeve counterclockwise (as viewed from the front) far enough to
accept the desired bit or accessory.
3. Insert the bit or other accessory about 3/4" (19 mm) into the chuck, as shown in Figure 9.
Grasp the chuck sleeve (I) securely and rotate the sleeve clockwise (viewed from the front)
with one hand while using the other hand to secure the tool. Rotate the sleeve clockwise
until sleeve cannot be rotated any further, as demonstrated in Figure 10. As the drill is being
operated in the forward position, the chuck will continually self tighten the jaws of the chuck
onto the bit or accessory to maximize the bit gripping strength.
To release the accessory, repeat Steps 1 and 2.
OPERATION
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool
from power source before making any adjustments or removing/installing attachments
or accessories.
Installing and Removing the Battery Pack (Fig. 11)
NOTE: Make sure your battery pack is fully charged.
To install the battery pack into the tool handle, align the notch inside the tool’s handle with the
battery pack and slide the battery pack firmly into the handle until you hear the lock snap into
place as shown in Figure 11.
To remove the battery pack from the tool, press the release buttons (J) and firmly pull the
battery pack out of the tool handle. Insert it into the charger as described in the charger section
of this manual.
Drill Operation
1. Select the desired speed/torque range using the gear shifter to match the speed and torque
to the planned operation. Set the mode control collar to the drill symbol.
2. For WOOD, use twist bits, spade bits, power auger bits or hole saws. For METAL, use high-
speed steel twist drill bits or hole saws. Use a cutting lubricant when drilling metals. The
exceptions are cast iron and brass which should be drilled dry.
3. Always apply pressure in a straight line with the bit. Use enough pressure to keep the drill
bit biting, but do not push hard enough to stall the motor or deflect the bit.
4. Hold tool firmly with both hands to control the twisting action of the drill.
5. IF DRILL STALLS, RELEASE TRIGGER it is usually because it is being overloaded.
IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT
CLICK TRIGGER OFF AND ON IN AN ATTEMPT TO START A STALLED DRILL – THIS
CAN DAMAGE THE DRILL.
6. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent
jamming.
make up the total length, be sure each individual extension contains at least the minimum
wire size. The following table shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge
number, the heavier the cord.
Recommended Minimum Wire Size for Extension Cords
Total Length of Cord
25 ft. 50 ft. 75 ft. 100 ft. 125 ft. 150 ft. 175 ft.
7.6 m 15.2 m 22.9 m 30.5 m 38.1 m 45.7 m 53.3 m
Wire Size AWG
18 18 16 16 14 14 12
• Do not place any object on top of charger or place the charger on a soft surface that
might block the ventilation slots and result in excessive internal heat. Place the charger
in a position away from any heat source. The charger is ventilated through slots in the top
and the bottom of the housing.
• Do not operate charger with damaged cord or plug.
• Do not operate charger if it has received a sharp blow, been dropped, or otherwise
damaged in any way. Take it to an authorized service center.
• Do not disassemble charger; take it to an authorized service center when service or
repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or
fire.
• Disconnect the charger from the outlet before attempting any cleaning. This will
reduce the risk of electric shock. Removing the battery pack will not reduce this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on standard 120V household electrical power. Do
not attempt to use it on any other voltage. This does not apply to the vehicular charger.
Using Automatic Tune-Up™ Mode
The automatic Tune-Up™ Mode equalizes or balances the individual cells in the battery pack
allowing it to function at peak capacity. Battery packs should be tuned up weekly or after
10 charge/discharge cycles or whenever the pack no longer delivers the same amount of work.
To use the automatic Tune-Up™, place the battery pack in the charger and leave it for at least
8 hours. The charger will cycle through the following modes.
1. The red light will blink continuously indicating that the 1-hour charge cycle has started.
2. When the 1-hour charge cycle is complete, the light will stay on continuously and will no
longer blink. This indicates that the pack is fully charged and can be used at this time.
3. If the pack is left in the charger after the initial 1-hour charge, the charger will begin the
Automatic Tune-Up™ mode. This mode continues up to 8 hours or until the individual cells
in the battery pack are equalized. The battery pack is ready for use and can be removed at
any time during the Automatic Tune-Up™ mode.
4. Once the Automatic Tune-Up™ mode is complete, the charger will begin a maintenance
charge; the red indicator will remain lit.
Chargers
Your tool uses a D WALT 12, 14,4 or 18 volt charger. Be sure to read all safety instructions E
before using your charger. Consult the chart at the end of this manual for compatibility of
chargers and battery packs.
Charging Procedure
DANGER: Electrocution hazard. 120 volts present at charging terminals. Do not probe with
conductive objects. Danger of electric shock or electrocution.
1. Plug the charger into an appropriate outlet before inserting battery pack.
2. Insert the battery pack into the charger. The red (charging) light will blink continuously
indicating that the charging process has started.
3. The completion of charge will be indicated by the red light remaining ON continuously. The
pack is fully charged and may be used at this time or left in the charger.
Indicator Light Operation
Charge Indicators
Some chargers are designed to detect certain problems that can arise with battery packs.
Problems are indicated by the red light flashing at a fast rate. If this occurs, re-insert battery pack
into the charger. If the problem persists, try a different battery pack to determine if the charger is
OK. If the new pack charges correctly, then the original pack is defective and should be returned
to a service center or other collection site for recycling. If the new battery pack elicits the same
trouble indication as the original, have the charger tested at an authorized service center.
HOT/COLD PACK DELAY
Some chargers have a Hot/Cold Pack Delay feature: when the charger detects a battery that is
hot, it automatically starts a Hot Pack Delay, suspending charging until the battery has cooled.
After the battery has cooled, the charger automatically switches to the Pack Charging mode.
This feature ensures maximum battery life. The red light flashes long, then short while in the
Hot Pack Delay mode.
PROBLEM POWER LINE
Some chargers have a Problem Power Line indicator. When the charger is used with some
portable power sources such as generators or sources that convert DC to AC, the charger may
temporarily suspend operation, flashing the red light with two fast blinks followed by a
pause. This indicates the power source is out of limits.
LEAVING THE BATTERY PACK IN THE CHARGER
The charger and battery pack can be left connected with the red light glowing indefinitely. The
charger will keep the battery pack fresh and fully charged.
NOTE: A battery pack will slowly lose its charge when kept out of the charger. If the battery pack
has not been kept on maintenance charge, it may need to be recharged before use. A battery
pack may also slowly lose its charge if left in a charger that is not plugged into an appropriate
AC source.
WEAK BATTERY PACKS: Chargers can also detect a weak battery pack. Such batteries are
still usable but should not be expected to perform as much work. The charger will indicate to
replace battery pack.
Important Charging Notes
1. Longest life and best performance can be obtained if the battery pack is charged when the
air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack in
an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and
will prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to touch while charging. This is a normal
condition, and does not indicate a problem. To facilitate the cooling of the battery pack after
use, avoid placing the charger or battery pack in a warm environment such as in a metal
shed, or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp or other appliance;
b. Check to see if receptacle is connected to a light switch which turns power off when you
turn out the lights;
c. Move charger and battery pack to a location where the surrounding air temperature is
approximately 65°F - 75°F (18°- 24°C);
d. If charging problems persist, take the tool, battery pack and charger to your local service
center.
4. The battery pack should be recharged when it fails to produce sufficient power on jobs which
were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the
charging procedure. You may also charge a partially used pack whenever you desire with
no adverse affect on the battery pack.
5. Under certain conditions, with the charger plugged into the power supply, the exposed
charging contacts inside the charger can be shorted by foreign material. Foreign materials
of a conductive nature such as, but not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles should be kept away from charger cavities.
Always unplug the charger from the power supply when there is no battery pack in the cavity.
Unplug charger before attempting to clean.
6. Do not freeze or immerse charger in water or any other liquid.
WARNING: Shock hazard. Don’t allow any liquid to get inside charger. Electric shock may
result.
CAUTION: Never attempt to open the battery pack for any reason. If the plastic housing of the
battery pack breaks or cracks, return to a service center for recycling.
Storage Recommendations
1. The best storage place is one that is cool and dry away from direct sunlight and excess heat
or cold.
2. Long storage will not harm the battery pack or charger. Under proper conditions, they can
be stored for 5 years or more.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
COMPONENTS (Fig. 1)
A. Trigger switch F. Mode control collar
B. Forward/reverse button G. Gear shifter
C. LED light H. Side handle (DCD940, DCD950,
D. Chuck DCD960, DCD970 only)
E. Torque adjustment collar
Variable Speed Switch (Fig. 1)
To turn the tool on, squeeze the trigger switch (A). To turn the tool off, release the trigger switch.
Your tool is equipped with a brake. The chuck will stop as soon as the trigger switch is fully
released.
NOTE: Continuous use in variable speed range is not recommended. It may damage the switch
and should be avoided.
Side Handle (Fig. 1)
WARNING: ALWAYSTo reduce the risk of personal injury, operate the tool with the side
handle properly installed. Failure to do so may result in the side handle slipping during tool
operation and subsequent loss of control. Hold tool with both hands to maximize control.
Side handle (H) clamps to the front of the gear case and may be rotated 360˚ to permit right- or
left-hand use. Side handle must be tightened sufficiently to resist the twisting action of the tool
if the accessory binds or stalls. Be sure to grip the side handle at the far end to control the tool
during a stall.
If model is not equipped with side handle, grip drill with one hand on the handle and one hand
on the battery pack.
NOTE: Side handle comes equipped on models DCD940, DCD950, DCD960 and DCD970.
Forward/Reverse Control Button (Fig. 1)
A forward/reverse control button (B) determines the direction of the tool and also serves as a
lock off button.
To select forward rotation, release the trigger switch and depress the for ward/re verse control
button on the right side of the tool.
To select reverse, release the trigger switch and depress the forward/reverse control button on
the left side of the tool.
The center position of the control button locks the tool in the OFF position. When changing the
position of the control button, be sure the trigger is released.
NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click
on start up. This is normal and does not indicate a problem.
Worklight (Fig. 1)
There is a worklight (C) located just above the trigger switch (A). The worklight will be activated
when the trigger switch is squeezed.
NOTE: The worklight is for lighting the immediate work surface and is not intended to be used
as a flashlight.
FIG. 5 FIG. 6 FIG. 7
FIG. 8 FIG. 9 FIG. 10
D
I
FIG. 11
J
DCD940
A
B
D E F
C
DCD950
A
B
D E F
C
FIG. 1
G
G
FIG. 2
E
F
G
SCREWDRIVING
VISSAGE
DESTORNILLADO
HAMMERDRILLING
MARTEAU PERFORATEUR
TALADRADO DE PERCUSIÓN
DRILLING
PERÇAGE
TALADRADO
E
F
G
H
FIG. 4FIG. 3
Screwdriver Operation
1. Select the desired speed/torque range using the three-speed gear shifter (G) on the top of tool
to match the speed and torque to the planned application. Initially set the torque adjustment
collar (E) at a lower setting to ensure the fastener to be set to your specification.
NOTE: Use the lowest torque setting required to seat the fastener at the desired depth. The
lower the number, the lower the torque output.
2. Rotate the mode control collar (F) so the screw symbol is aligned with the arrow.
3. Reset the torque adjustment collar (E) to the appropriate number setting for the torque
desired. Make a few practice runs in scrap or unseen areas to determine the proper position
of the torque adjustment collar.
NOTE: The torque adjustment collar may be set to any number at any time. However, the torque
adjustment collar is only engaged during screwdriving mode and not in drill and hammerdrill
modes.
Hammerdrill Operation
1. Select the desired speed/torque range using the gear shifter to match the speed and torque
to the planned operation. Set the mode control collar to the hammer symbol.
1. When drilling, use just enough force on the hammer to keep it from bouncing excessively.
Too much force will cause slower drilling speeds, overheating, and a lower drilling rate.
2. Drill straight, keeping the bit at a right angle to the work. Do not exert side pressure on the
bit when drilling as this will cause clogging of the bit flutes and a slower drilling speed.
3. When drilling deep holes, if the hammer speed starts to drop off, pull the bit partially out of
the hole with the tool still running to help clear debris from the hole.
4. For MASONRY, use carbide-tipped bits or masonry bits. A smooth, even flow of dust
indicates the proper drilling rate.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool
from power source before making any adjustments or removing/installing attachments
or accessories.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
performing this.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning.
Dirt and grease may be removed from the exterior of the charger using a cloth or soft
non-metallic brush. Do not use water or any cleaning solutions.
Accessories
WARNING: Since accessories, other than those offered by D WALT, have not been tested E
with this product, use of such accessories with this tool could be hazardous. To reduce the risk
of injury, only DEWALT, recommended accessories should be used with this product.
Recommended accessories for use with your tool are available at extra cost from your local
service center. If you need any assistance in locating any accessory, please contact DEWALT
Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT
(1-800-433-9258) or visit our website www.dewalt.com.
MAXIMUM RECOMMENDED CAPACITIES
Speed 1 Speed 2 Speed 3
BITS, METALDRILLING 1/2" (12,7 mm) 1/4" (6.4 mm) 1/4" (6.4 mm)
WOOD, FLATBORING 1-1/2" (38.1 mm) 5/8" (15.9 mm) 5/8" (15.9 mm)
BITS, MASONRYDRILLING – 1/4" (6.4 mm) 1/4" (6.4 mm)
Repairs
The charger is not serviceable. There are no serviceable parts inside the charger.
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments (including
brush inspection and replacement) should be performed by a DEWALT factory service center,
a DEWALT authorized service center or other qualified service personnel. Always use identical
replacement parts.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials or workmanship for
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to
accessories or damage caused where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have other rights which vary in certain
states or provinces.
In addition to the warranty, DEWALT tools are covered by our:
1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time
during the first year after purchase.
2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS
DC9071, DC9091, DC9096, DC9280, DC9360 and DC9180
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or
Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt
for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, see country specific warranty information contained either in the
packaging, call the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-DEWALT for a free replacement.
d) Retirer toute clé de réglage avant de démarrer l’outil. Une clé laissée sur une pièce
rotative d’un outil électrique pose des risques de blessure.
e) Ne pas effectuer de travaux hors de portée. Les pieds doivent rester bien ancrés au
sol afin de maintenir son équilibre en tout temps. Cela permet de mieux maîtriser l’outil
électrique dans les situations imprévues.
f) Porter des vêtements appropriés. Ne pas porter de vêtements amples ni de bijoux.
Maintenir cheveux, vêtements et gants éloignés des pièces mobiles. Vêtements
amples, bijoux ou cheveux longs risquent de rester coincés dans ces pièces mobiles.
g) Lorsqu’un dispositif de connexion à un système de dépoussiérage ou d’élimination
est fourni, s’assurer qu’il est connecté et utilisé correctement. L’utilisation d’aspirateurs
peut réduire les risques engendrés par les poussières.
4) UTILISATION ET ENTRETIEN DES OUTILS ÉLECTRIQUES
a) Ne pas forcer un outil électrique. Utiliser l’outil approprié au travail en cours. L’outil
approprié effectuera un meilleur travail, de façon plus sûre et à la vitesse pour laquelle il a
été conçu.
b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout appareil
dont l’interrupteur est défectueux est dangereux et doit être réparé.
c) Débrancher la fiche du secteur et/ou le bloc-piles de l’outil électrique avant de
faire tout réglage ou changement d’accessoire, ou avant de ranger ce dernier. Ces
mesures préventives réduisent les risques de démarrage accidentel de l’appareil.
d) Après usage, ranger les outils électriques hors de la portée des enfants, et ne
permettre à aucune personne n’étant pas familière avec un outil électrique (ou son
manuel d’instruction) d’utiliser ce dernier. Les outils peuvent être dangereux entre les
mains des novices.
e) Entretenir les outils électriques. Vérifier les pièces mobiles pour s’assurer qu’elles
sont bien alignées et tournent librement, qu’elles sont en bon état et ne sont
affectées d’aucune condition susceptible de nuire au bon fonctionnement de l’outil.
En cas de dommage, faire réparer l’outil électrique avant toute nouvelle utilisation.
Bien des accidents sont causés par des outils mal entretenus.
f) Maintenir toute lame aiguisée et propre. Les outils de coupe bien entretenus et affûtés
sont moins susceptibles de se coincer et sont plus faciles à contrôler.
g) Utiliser un outil électrique, ses accessoires, mèches, etc., conformément aux
présentes directives en tenant compte des conditions de travail et du travail à
effectuer. L’utilisation d’un outil électrique pour toute opération autre que celle pour
laquelle il a été conçu est dangereuse.
5) UTILISATION ET ENTRETIEN DU BLOC-PILES
a) Ne recharger l’outil qu’au moyen du chargeur précisé par le fabricant. L’utilisation
d’un chargeur qui convient à un type de bloc-piles risque de provoquer un incendie s’il est
utilisé avec un autre type de b loc-piles.
b) Utiliser les outils électriques uniquement avec les blocs-piles conçus à cet effet.
L’utilisation de tout autre bloc-piles risque de causer des blessures ou un incendie.
c) Lorsque le bloc-piles n’est pas utilisé, le tenir éloigné des objets métalliques,
notamment des trombones, de la monnaie, des clés, des clous, des vis ou autres
petits objets métalliques qui peuvent établir une connexion entre les deux bornes. Le
court-circuit des bornes du bloc-piles risque de provoquer des brûlures ou un incendie.
d) En cas d’utilisation abusive, le liquide peut gicler hors du bloc-piles; éviter tout
contact avec ce liquide. Si un contact accidentel se produit, laver à grande eau. Si
le liquide entre en contact avec les yeux, obtenir également des soins médicaux. Le
liquide qui gicle hors du bloc-piles peut provoquer des irritations ou des brûlures.
6) SERVICE
a) Faire entretenir les outils électriques par un réparateur qualifié en utilisant
seulement des pièces de rechange identiques. Cela permettra d’assurer l’intégrité de
l’outil électrique et la sécurité de l’utilisateur.
Règles de sécurité spécifiques
• Une Porter des protecteurs auditifs si une perceuse à percussion est utilisée.
exposition au bruit peut entraîner une perte auditive.
• Utiliser les poignées auxiliaires fournies avec l’outil. Une perte de maîtrise de l’outil peut
entraîner des blessures corporelles.
• Tenir l’outil par sa surface de prise isolée dans une situation où l’outil risque d’entrer
en contact avec un câblage caché. Tout contact avec un fil « sous tension » mettra « sous
tension » les pièces métalliques de l’outil et électrocutera l’opérateur de l’outil.
• Utiliser des brides de fixation ou tout autre dispositif de fixation permettant de soutenir
et de retenir la pièce sur une plate-forme stable. Tenir la pièce avec la main ou contre son
corps est instable et risque de provoquer une perte de maîtrise de l’outil.
• Porter des protecteurs auditifs lors de martelage sur des périodes prolongées. Une
exposition prolongée à un bruit d’intensité élevé peut provoquer une perte auditive. Les
niveaux sonores élevés produits par le marteau perforateur pourraient provoquer une perte
auditive temporaire ou endommager gravement les tympans.
• Porter des lunettes de sécurité ou une autre protection oculaire. Le martelage et la
perforation peuvent projeter des fragments. Les particules projetées peuvent endommager les
yeux irréversiblement. La protection auditive peut être exigée pour la plupart des applications.
• Tenir fermement l’outil en tout temps. Ne pas utiliser l’outil sans le tenir des deux
mains. Il est recommandé d’utiliser en tout temps la poignée latérale. Faire fonctionner cet
outil d’une seule main risque de provoquer la perte de maîtrise de l’outil. Il peut aussi être
dangereux de percer ou de tomber sur des matériaux durs comme une barre d’armature.
• Les accessoires et l’outil peuvent devenir brûlants au toucher pendant l’utilisation.
Porter des gants pendant leur utilisation pour effectuer des travaux produisant beaucoup de
chaleur comme la perforation à percussion et le perçage des métaux.
• Ne pas utiliser cet outil pendant des périodes de temps prolongées. Les vibrations
causées par la percussion peuvent poser des risques pour les mains ou les bras. Porter des
gants pour amortir les vibrations, et pour limiter les risques, faire des pauses fréquentes.
• Prendre des précautions à proximité des évents car ils cachent des pièces mobiles.
Vêtements amples, bijoux ou cheveux longs risquent de rester coincés dans ces pièces
mobiles.
AVERTISSEMENT : TOUJOURS porter des lunettes de sécurité. Les lunettes de vue
ne constituent PAS des lunettes de sécurité. Utiliser également un masque facial ou anti-
poussière si l’opération de découpe génère de la poussière. TOUJOURS UTILISER DE
L’ÉQUIPEMENT DE PROTECTION HOMOLOGUÉ :
• protection oculaire conforme à la norme ANSI Z87.1 (CAN/CSA Z94.3),
• protection auditive conforme à la norme ANSI S12.6 (S3.19) et
• protection des voies respiratoires conformes aux normes NIOSH/OSHA.
AVERTISSEMENT : Certaines poussières créées par le ponçage, le sciage, le meulage et le
forage mécaniques ainsi que d’autres activités de construction contiennent des produits
chimiques reconnus pour causer le cancer, des anomalies congénitales ou d’autres anomalies
liées à la reproduction. Parmi ces produits chimiques, citons notamment :
• le plomb provenant des peintures au plomb ;
• la silice cristalline provenant des briques, du béton et d’autres matériaux de
maçonnerie ;
• l’arsenic et le chrome provenant du bois traité (arséniate de cuivre et de chrome).
Le risque associé à ces expositions varie selon la fréquence de ces types de travaux. Pour
réduire l’exposition aux produits chimiques : travailler dans un local bien ventilé et utiliser du
matériel de sécurité approuvé, comme les masques antipoussières spécialement conçus pour
filtrer les particules microscopiques.
• Éviter le contact prolongé avec la poussière provenant du ponçage, du sciage, du
meulage et du forage mécanique ainsi que d’autres activités de construction. Porter
des vêtements de protection et laver les parties exposées au savon et à l’eau. La
poussière qui pourrait pénétrer dans la bouche et les yeux ou se déposer sur la peau peut
favoriser l’absorption de produits chimiques nocifs.
AVERTISSEMENT : Cet outil peut produire et répandre de la poussière susceptible de causer
des dommages sérieux et permanents au système respiratoire. Toujours utiliser un appareil
respiratoire anti-poussières approuvé par le NIOSH ou l’OSHA. Diriger les particules dans le
sens opposé du visage et du corps.
AVERTISSEMENT : TOUJOURS porter une protection auditive appropriée conformément
à la norme ANSI S12.6 (S3.19) lors de l’utilisation du produit. Dans certaines conditions et
selon la durée d’utilisation, le bruit émis par ce produit peut contribuer à une perte auditive.
ATTENTION : Après utilisation, ranger l’outil sur son côté sur une surface stable là où
il ne pourra faire ni trébucher ni tomber personne. Certains outils équipés d’un large bloc-pile
peuvent tenir à la verticale sur ce dernier mais ils sont alors facilement déstabilisés.
• L’étiquette apposée sur votre outil peut comprendre les symboles suivants. Les symboles et
leurs définitions sont indiqués ci-après :
V ..................volts A .................ampères
Hz ................hertz W ................watts
min ..............minutes ..............courant alternatif
...........courant continu ..............courant alternatif ou continu
................Construction de classe I no ...............vitesse à vide
....................(mis à la terre) ................borne de terre
................Construction de classe II ...............symbole d’alerte à la sécurité
....................(à double isolation) BPM ...........coups par minute
RPM ............rotations ou alternance …/min .........par minute
....................par minute IPM .............impacts par minute
Directives de sécurité importantes pour tous
les blocs-piles
Pour la commande d’un bloc-piles de rechange, s’assurer d’inclure le numéro de catalogue
et la tension. Consulter le tableau figurant à la fin du présent mode d’emploi pour connaître la
compatibilité des chargeurs et des blocs-piles.
Le bloc-piles n’est pas complètement chargé à la sortie de l’emballage. Avant d’utiliser le bloc-
piles et le chargeur, lire les directives de sécurité ci-après. Respecter ensuite les consignes de
chargement décrites.LIRE TOUTES LES DIRECTIVES
• Ne pas charger ou utiliser un bloc-piles dans un milieu déflagrant, en présence
de liquides, de gaz ou de poussière inflammables. Insérer ou retirer un bloc-piles du
chargeur peut enflammer de la poussière ou des émanations.
• NE JAMAIS forcer l’insertion d’un bloc-piles dans le chargeur. Ne pas modifier un
bloc-piles de quelque façon que ce soit pour l’insérer dans un chargeur incompatible,
car il risque de se rompre et de provoquer de graves blessures corporelles. Consulter
le tableau figurant à la fin du présent manuel pour connaître la compatibilité des piles et des
chargeurs.
• Charger les blocs-piles uniquement au moyen de chargeurs DEWALT.
• NE PAS éclabousser le bloc-piles ni l’immerger dans l’eau ou dans tout autre liquide.
• Ne pas ranger ni utiliser l’outil et le bloc-piles à un endroit où la température peut
atteindre ou dépasser les 40 °C (105 °F) (comme dans les remises extérieures ou les
bâtiments métalliques l’été).
DANGER : Risque d’électrocution. Ne jamais ouvrir le bloc-piles pour quelque raison que
ce soit. Si le boîtier du bloc-piles est fissuré ou endommagé, ne pas l’insérer dans un chargeur.
Ne pas écraser, faire tomber ou endommager le bloc-piles. Ne pas utiliser un bloc-piles ou un
chargeur qui a reçu un choc violent, qui est tombé, a été écrasé ou est endommagé de quelque
manière que ce soit (p. ex. percé par un clou, frappé d’un coup de marteau, piétiné). En effet,
il y a risque de choc électrique ou d’électrocution. Les blocs-piles endommagés doivent être
envoyés au centre de réparation pour être recyclés.
REMARQUE : un boîtier spécial et des capuchons de sécurité sont fournis
avec le bloc-piles pour utilisation chaque fois qu’on le retire de l’outil ou du
chargeur pour le ranger ou le transporter. Enlever le capuchon avant de remettre
le bloc-piles dans le chargeur ou l’outil.
AVERTISSEMENT : Risque d’incendie. Ne pas ranger ni ne transporter les piles de
manière à ce que des objets métalliques puissent entrer en contact avec les bornes
exposées des piles. On ne doit pas mettre, par exemple, le bloc-piles sans capuchon dans
un tablier, une poche, une boîte à outils, une boîte de nécessaire de produit, un tiroir, etc. avec
des clous, des vis, des clés, etc. Le transport des piles peut causer un incendie si les
bornes des piles entrent en contact involontairement avec des matières conductrices
comme des clés, de la monnaie, des outils manuels et d’autres éléments semblables. La
Hazardous Material Regulations (réglementation sur les produits dangereux) du département
américain des transports interdit en fait le transport des blocs-piles pour le commerce et dans les
avions (c.-à-d. dans des valises et les bagages à main) À MOINS qu’ils ne soient bien protégés
Définitions : lignes directrices en
matière de sécurité
Les définitions ci-dessous décrivent le niveau de danger pour chaque
mot-indicateur employé. Veuillez lire le mode d’emploi et porter une attention
particulière à ces symboles.
DANGER : indique une situation dangereuse imminente qui, si elle n’est pas
évitée, .causera la mort ou des blessures graves
AVERTISSEMENT : indique une situation potentiellement dangereuse qui, si elle
n’est pas évitée, se solder par un pourrait décès ou des blessures graves.
ATTENTION : indique une situation potentiellement dangereuse
qui, si elle n’est pas évitée se solder parpourrait des blessures mineures ou
modérées.
ATTENTION : utilisé sans le symbole d’alerte à la sécurité, indique une situation
potentiellement dangereuse qui, si elle n’est pas évitée se solder par pourrait des
dommages à la propriété.
POUR TOUT COMMENTAIRE OU QUESTION RELATIF À CET OUTIL OU TOUT AUTRE
OUTIL DEWALT, COMPOSEZ GRATUITEMENT LE : 1-800-4-DEWALT (1-800-433-9258).
AVERTISSEMENT : Pour réduire tout risque de dommage corporel, lire le manuel de
l’utilisateur.
Directives de sécurité relatives aux outils électriques
en général
AVERTISSEMENT! Lire toutes les directives et consignes de sécurité. Tout
manquement aux directives et consignes pose des risques de décharge électrique,
d’incendie et/ou de blessure grave.
CONSERVER TOUTES CES DIRECTIVES
ET CONSIGNES À TITRE DE RÉFÉRENCE
Le terme « outil électrique » dans ces directives se rapporte à votre outil électrique alimenté sur
secteur (avec fil) ou par piles (sans fil).
1) SÉCURITÉ - AIRE DE TRAVAIL
a) Maintenir l’aire de travail propre et bien éclairée. Les lieux encombrés ou sombres sont
propices aux accidents.
b) Ne pas faire fonctionner un outil électrique dans une atmosphère explosive, en
présence par exemple de poussières, gaz ou liquides inflammables. Les outils
électriques peuvent produire des étincelles qui pourraient enflammer toute émanation ou
poussière ambiante.
c) Tenir les enfants, ou toute autre personne, à l’écart pendant l’utilisation d’un outil
électrique. Toute distraction pourrait faire perdre la maîtrise de l’appareil.
2) SÉCURITÉ – ÉLECTRICITÉ
a) La fiche électrique de l’outil doit correspondre à la prise murale. Ne jamais modifier
la fiche en aucune façon. Ne jamais utiliser de fiche d’adaptation avec un outil
électrique mis à la terre. L’utilisation de fiches d’origine et de prises appropriées réduira
les risques de choc électrique.
b) Éviter tout contact corporel avec des éléments mis à la terre comme tuyaux,
radiateurs, cuisinières ou réfrigérateurs. Les risques de choc électrique augmentent
lorsque le corps est mis à la terre.
c) Ne pas exposer les outils électriques à la pluie ou à l’humidité. Toute pénétration d’un
outil électrique par un liquide augmente les risques de choc électrique.
d) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour
transporter, tirer ou débrancher un outil électrique. Protéger le cordon de la chaleur,
de l’huile et de tout bord tranchant ou pièce mobile. Les cordons endommagés ou
emmêlés augmentent les risques de choc électrique.
e) Lors de l’utilisation d’un outil électrique à l’extérieur, n’utiliser que des rallonges
conçues pour l’extérieur. L’utilisation d’une rallonge conçue pour l’extérieur réduit les
risques de choc électrique.
f) Si l’utilisation d’un outil électrique en milieu humide est inévitable, utiliser une
alimentation protégée par un disjoncteur de fuites à la terre (DDFT). L’utilisation d’un
DDFT réduit les risques de choc électrique.
3) SÉCURITÉ PERSONNELLE
a) Rester constamment vigilant et faire preuve de jugement pendant l’utilisation
d’un outil électrique. Ne pas utiliser d’outil électrique en cas de fatigue ou sous
l’influence de drogues, d’alcool ou de médicaments. Tout moment d’inattention
pendant l’utilisation d’un outil électrique pose des risques de blessure grave.
b) Utiliser un équipement de protection individuel. Porter systématiquement des
lunettes de protection. Le fait de porter un équipement de protection tel que masque
antipoussières, chaussures antidérapantes, casque de sécurité ou protecteurs auditifs
lorsque la situation le requiert, réduira les risques de dommages corporels.
c) Prévenir tout démarrage accidentel. S’assurer que l’interrupteur est en position
d’arrêt avant de brancher l’outil et/ou de le connecter à un bloc-piles, et avant de le
saisir ou de le transporter. Transporter un outil le doigt sur l’interrupteur, ou brancher un
outil électrique alors que l’interrupteur est en position de marche, invite les accidents.
Termékspecifikációk
| Márka: | DeWalt |
| Kategória: | fúrógép |
| Modell: | DCD960 |
Szüksége van segítségre?
Ha segítségre van szüksége DeWalt DCD960, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók fúrógép DeWalt
24 December 2024
14 Október 2024
21 Szeptember 2024
20 Szeptember 2024
18 Szeptember 2024
16 Szeptember 2024
15 Szeptember 2024
12 Szeptember 2024
4 Szeptember 2024
4 Szeptember 2024
Útmutatók fúrógép
- fúrógép Milwaukee
- fúrógép Parkside
- fúrógép Worx
- fúrógép Bosch
- fúrógép AEG
- fúrógép Einhell
- fúrógép Ozito
- fúrógép Makita
- fúrógép Hyundai
- fúrógép Flex
- fúrógép Scheppach
- fúrógép Ergotools Pattfield
- fúrógép Ribimex
- fúrógép Mafell
- fúrógép Kraftixx
- fúrógép Genesis
- fúrógép Güde
- fúrógép Hitachi
- fúrógép Toolcraft
- fúrógép Hilti
- fúrógép Black & Decker
- fúrógép Workzone
- fúrógép Global
- fúrógép Kawasaki
- fúrógép Fieldmann
- fúrógép GO/ON
- fúrógép PowerPlus
- fúrógép DEDRA
- fúrógép Metabo
- fúrógép Handwerk
- fúrógép Powerfix
- fúrógép Bavaria
- fúrógép RYOBI
- fúrógép Proxxon
- fúrógép HiKOKI
- fúrógép Festool
- fúrógép Yato
- fúrógép Baumr-AG
- fúrógép McKenzie
- fúrógép Trotec
- fúrógép Delta
- fúrógép Zipper
- fúrógép Bavaria By Einhell
- fúrógép Herkules
- fúrógép Porter-Cable
- fúrógép Tanaka
- fúrógép Stanley
- fúrógép Silverline
- fúrógép Vonroc
- fúrógép Cotech
- fúrógép Alpha Tools
- fúrógép Luxor
- fúrógép Holzmann
- fúrógép Fein
- fúrógép Max Bahr
- fúrógép Cocraft
- fúrógép Craftsman
- fúrógép Maestro
- fúrógép Graphite
- fúrógép Hazet
- fúrógép Ferm
- fúrógép Tryton
- fúrógép Skil
- fúrógép Meec Tools
- fúrógép Sun Joe
- fúrógép Dremel
- fúrógép Tacklife
- fúrógép Maktec
- fúrógép Steren
- fúrógép Bort
- fúrógép Malmbergs
- fúrógép Power Craft
- fúrógép Eibenstock
- fúrógép Topcraft
- fúrógép Festo
- fúrógép Sparky
- fúrógép Gamma
- fúrógép Clas Ohlson
- fúrógép Carat
- fúrógép Kress
- fúrógép Duro
- fúrógép Varo
- fúrógép Defort
- fúrógép Truper
- fúrógép Kinzo
- fúrógép Bruder Mannesmann
- fúrógép Powerblade
- fúrógép Meister Craft
- fúrógép RIDGID
- fúrógép Rupes
- fúrógép Batavia
- fúrógép Protool
- fúrógép Westfalia
- fúrógép Economy
- fúrógép Huvema
- fúrógép Black Decker
- fúrógép Stomer
- fúrógép Fe Powertools
- fúrógép Elu
- fúrógép Blucave
- fúrógép Lux Tools
- fúrógép Wolfcraft
- fúrógép Kreg
- fúrógép Sthor
- fúrógép Verto
- fúrógép Wurth
- fúrógép Spit
- fúrógép King Craft
- fúrógép Rok
- fúrógép Profitech
- fúrógép Narex
- fúrógép Rikon
- fúrógép Duro Pro
- fúrógép Baier
- fúrógép RUKO
- fúrógép Felisatti
- fúrógép MSW
- fúrógép Robust
- fúrógép Einhell Bavaria
- fúrógép MyTool
- fúrógép G-Technology
- fúrógép Rodcraft
- fúrógép Stalco
- fúrógép Total
Legújabb útmutatók fúrógép
25 December 2024
23 December 2024
22 December 2024
19 December 2024
17 December 2024
16 December 2024
16 December 2024
16 December 2024
15 December 2024
15 December 2024