Használati útmutató Delta Dore Tyxia 611

Delta Dore Megkönnyebbülés Tyxia 611

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Delta Dore Tyxia 611 (1 oldal) a Megkönnyebbülés kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/1
The TYXIA 611 pack enables
you to create a two-way lighng
without an exisng switch.
Recommendaons
IMPORTANT: the control wires are not
insulated from the mains power supply.
All connected equipment must be marked CE
and meet the requirements of the low voltage
devices as well as assembly recommendaons.
Local control wires can be extended up to 10
m (separate from the 230 V).
10A circuit breaker required.
Step 1 - Install your products
230V~
OFF
You can install the lighng receiver in a flush-mounted
box, behind a switch or control push-buon
(automac detecon on use) or behind a ceiling.
1.1 Connecon instrucons for terminals 1 2 3 4.
Strip the wires while respecng the strip length specified on the product.
1.1.1 Solid wires 1.1.2 Stranded wires
Push the wire fully
into the terminal.
Removal recommendaons
- Switch off the power supply.
- Use the tool supplied or a 2.5 mm screwdriver
to press the buon of the front terminal before
removing the wire. 2
1
1.2 Connecon instrucons for IN1 - COM - IN2 terminals
Use the wires supplied.
Push the wire fully into the terminal.
1.3 TYXIA 5610 connecon
Connect:
The light to terminals 3 and 4.
The switch to the IN1 -
COM terminals (input 1).
The 230 V power supply to terminals 1
and 2.
Switch the installaon power back on to
connue with the associaon operaon.
1.4 TYXIA 2310 installaon
This unit must not be placed on a metal surface.
Configuraon buons
Step 2 - Determine the operang mode of the TYXIA 2310
The operang mode of the TYXIA 2310 is, by default, mode A, i.e. for control-
ling 2 ON/OFF lighng channels.
IMPORTANT: If you approve this selecon, go directly to step 3,
'Associate your products'.
Otherwise, determine the operang mode suited to your installaon.
Mode B: Scenario mode to simultaneously control different receivers.
Mode C: Dimmer mode to control a dimmer lighng channel.
Open the unit.
Press the T2 buon several mes to select
your desired operang mode.
...... ...
EXIT
1
2
ON/OFF
ON/OFF
... ... ...
Mode A Mode B Mode C
The LED fl ashes
once
The LED fl ashes
twice
The LED fl ashes
three  mes
Step 3 - Associate your products
❶Set the TYXIA 5610 receiver to associaon
standby mode. Press and hold the buon for 3
seconds unl the LED flashes, release.
❷ On the TYXIA 2310 emiers, send the
associaon order: Mode A or B: Press the
buon of the channel you want to associate
for 3 seconds (1 or 2).
Mode C: Press the 1 and 2 buons
at the same me and hold for 3 seconds.
❸ When the receiver LED has stopped flashing.
The products are now associated.
Number of associated emiers: 16 maximum
Troubleshoong
Summary of funcons accessible using the receiver buon
3’’
A
>10’’ 20’’>
C
>
B
Associaon/
Configuraon
Removing an
associaon
Removing
all associaons
Press and hold the buon for x seconds
AAssociaon/Configuraon
Press the receiver buon for 3 seconds unl the LED flashes, release.
BRemove an associaon
On the TYXIA 5610 receiver:
Press the receiver buon for 10 seconds unl the LED flashes rapidly, release.
On the TYXIA 2310 emier:
Mode A or B: Press the buon of the channel you want to delete for 3 seconds
(1 or 2).
Mode C: Press the 1 and 2 buons at the same me and hold for 3 seconds.
CRemove all associaons
Press the receiver's buon for 20 seconds.
Press and hold unl the LED switches off aer the rapid flashing phase, release.
The receiver has no wireless connecon.
The receiver locks in off mode
When an overload is detected, the product locks in off mode for 30 seconds be-
fore authorising a new acvaon. The LED flashes rapidly throughout this phase.
To exit the receiver from this secure mode, replace the bulb connected by a bulb
with lower power (refer to compability table).
You wish to change the operang mode of a product which has already been
associated. - You must first delete any associaon.
Replacing the baeries
Red Red Red
2s
The red LED flashes each me you press = Baery fault
Compability
① 230 V halogen or 230 V incandescent bulbs.
② 230V energy-saving compact fl uorescent bulbs.
③ 230V LED bulbs.
④ Very low voltage 12V halogen or LED bulbs with AC or DC electronic
transformer.
⑤Very low voltage 12V halogen bulbs with ferromagne c or toroidal transformer.
⑥Fluorescent tube.
200 W 100 W 100 W100 W100 W
LEDLED
150 W 100 W
M
Hi-Fi
230 V~ 50 Hz
2
1
230 V~
1
IN1
COM
TYXIA
5610
1 2 3 4
230V~
200W max
1234
Standby 0.06W
230 V~ 0.6 VA
IN1
CO M
IN1
CO M
ON
OFF
ON
OFF
230V~
µ
N S1NL
2
7mm 0,5 mm
KY31A02
123 4
230V
EN
Technical characteriscs
TYXIA 5610
- Power supply 230 V~ 0.6 VA
- Class II insulaon
Stand-by consumpon: 0.06 W
- Storage temperature: -10 °C / +70 °C
- Operang temperature: -10 °C / +40 °C
- IP 40 (flush mounng box)
- Dimensions: 41 x 36 x 14.5 mm
- X3D wireless remote control device:
868.7 MHz to 869.2 MHz
- Maximum wireless power < 10 mW Category 2 receiver
TYXIA 2310
- CR 2430 lithium baery power supply (included),
Baery life 10 years depending on use
- Storage temperature: -10 °C / +70 °C
- Operang temperature: -10 °C / +40 °C
- IP 40 - IK 04
- Dimensions: 84 x 84 x 13 mm
- X3D wireless remote control device:
868.7 MHz to 869.2 MHz
- Maximum wireless power < 10 mW Category 2 receiver
EN Wireless two-way pack
Use an electrically
isolated tool to per-
form the acons on
the receiver configu-
raon buon.
TYXIA
Switch off the installaon
power supply.
Do not strip the wires when they are
connected to the product as you
could damage the internal connector.
1 2 3 4
TYXIA
5610
TYXIA
5610
... ... ...
> 3s
µ
N S1NL
µ
N S1NL
1 2 3 4
TYXIA
5610
OK
OFF
µ
N S1NL
1
2
>3s
>3s
1
2
Removal recommendaons
Turn the wire while pulling on it.
1
2
123 4
TYXIA 2310
TYXIA 2310
TYXIA 5610
On / Off
On / Off
Alim. 230 V
230 V
200 W maxi.
TYXIA 611 pack
Using the tool
supplied or a 2.5
mm screwdriver,
press the terminal
buon then insert
the wire.
Important : If you have selected opera ng mode B (scenario
control), set each item to the required state (e.g. shu ers
lowered, ligh ng off ) before moving on to stage 1.

Termékspecifikációk

Márka: Delta Dore
Kategória: Megkönnyebbülés
Modell: Tyxia 611

Szüksége van segítségre?

Ha segítségre van szüksége Delta Dore Tyxia 611, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Megkönnyebbülés Delta Dore

Delta Dore

Delta Dore Easy Bulb GU10CW Útmutató

13 Augusztus 2024
Delta Dore

Delta Dore Tyxia 611 Útmutató

11 Augusztus 2024
Delta Dore

Delta Dore Tyxia 620 Útmutató

10 Augusztus 2024
Delta Dore

Delta Dore Tyxia 511 Útmutató

9 Augusztus 2024
Delta Dore

Delta Dore Easy Bulb E14CW Útmutató

8 Augusztus 2024
Delta Dore

Delta Dore Easy Bulb E27CW Útmutató

7 Augusztus 2024
Delta Dore

Delta Dore Easy Plug G13EM Útmutató

7 Augusztus 2024
Delta Dore

Delta Dore Tyxia 6610 Útmutató

6 Augusztus 2024
Delta Dore

Delta Dore Tyxia 501 Útmutató

4 Augusztus 2024

Útmutatók Megkönnyebbülés

Legújabb útmutatók Megkönnyebbülés

American DJ

American DJ Hydro Wash X19 Útmutató

30 Március 2025
American DJ

American DJ Saber Spot RGBW Útmutató

30 Március 2025
American DJ

American DJ Pixie Strip 120 Útmutató

30 Március 2025
Yongnuo

Yongnuo YNRAY260 Útmutató

30 Március 2025
Rollei

Rollei LUX Compact RGB Útmutató

30 Március 2025
Rollei

Rollei LUMIS Key Light Pro Útmutató

30 Március 2025
Rollei

Rollei LUMIS Mini RGB Útmutató

30 Március 2025
Rollei

Rollei LUX 100 Bi-Color Útmutató

30 Március 2025
Bresser

Bresser BR-150RGB Útmutató

28 Március 2025
Godox

Godox Litemons LP1200R Útmutató

28 Március 2025