Használati útmutató CRUX BEECR-35C

CRUX rádió BEECR-35C

Olvassa el alább 📖 a magyar nyelvű használati útmutatót CRUX BEECR-35C (6 oldal) a rádió kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/6

3-PIN

(female plug)

TO FACTORY

RADIO

TO FACTORY

HARNESS

24-PIN

(male plug)

10-PIN

(male plug)

3-PIN

(male plug)

22-PIN

(female plug)

22-PIN

(male plug)

MIC

INTERFACIN G SOLUTIONS

INT ERFAC ING SOLUT IONS

BLUETOOTH CONNECTIVITY FOR SELECT CHRYSLER, DODGE VEHICLES 2011-UP

CHRYSLER

2011 - 2013 300

DODGE

2011 - 2014 Charger

2014 - 2014 Durango

2013 - 2014 Journey

Vehicles listed above must have the “WHITE”

22-Pin connector.

Radio type does not matter.

Applications are subject to change

without notice.

BEECR-35C work. Following these instructions from “Start” to” Finish” will ensure

9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.

PARTS INCLUDED:

(1) CR-35C Interface Module

(1) CR-35C T-Harness

(1) Instruction Sheet

(1) Microphone

PRECAUTIONS:

- Remove the negative side of the battery to avoid any short circuits

during the installation.

- Do not install the interface near any major components or near the

HVAC system. This may cause damage or overheating to the vehicle.

PRELIMINARY:

Please read the entire manual before installing this interface.

THIS INTERFACE STREAMS THE HANDS-FREE & MUSIC (A2DP)

THROUGH THE TWO FRONT SPEAKERS ONLY.

MOUNTING THE MICROPHONE

1. Insert the mounting clip into the ball joint on the microphone.

2. Mount the clip on your visor or near the rear view mirror.

3. Route the remaining cable along the edge of the roof liner and

towards the back of the radio, hiding the cable from sight.

INSTALLING THE INTERFACE

1. Remove the factory radio from the dashboard.

2. Remove the factory connectors from behind the factory radio.

3. Mate the interface connections to the factory connectors.

Make sure the 22-pin connector is properly seated into the interface.

4. Route the microphone to your desired location. Recommended area

is above the rear-view mirror.

INITIAL PAIRING

1. Turn on the vehicle and wait 15 seconds until the interface

announces “Please Select Your Mobile Phone” and Enter “0000”

2. From your mobile phone, choose and connect to the “Beeline”

device using the password “0000”.

3. The interface will announce “Pairing Successful” then

“Phone Connected” after the pairing process is complete.

Note: The Bluetooth interface will remember up to the last 8 devices.

power back on to re-attempt, if unsuccessful please contact our tech

support line.

AUTO RE-CONNECT

The BEELINE module will automatically re-connect the previously

paired mobile phone when the ignition is turned “ON” to the vehicle

and the mobile phone’s Bluetooth feature is also on.

Note: The Bluetooth module will re-connect with the last mobile

phone it was paired with. If no mobile phone is found, it will

revert to the pairing process.

RADIO CONTROL

There is no Bluetooth control on the factory radio.

All controls are done from the steering wheel controls.

STEERING WHEEL CONTROLS

All Bluetooth functionality is done on the steering wheel controls.

INSTALLATION OVERVIEW

ENABLE VOICE DIAL AND MENU STRUCTURE

Rev. 051315

SEEK UP

SEEK DN

VOL UP

VOL DN

BACKSIDE CONTROLS

All functionality are done on the steering wheel controls.

MODELS LISTED BELOW MUST

BE EQUIPPED WITH SWC.

WHITE 22-PIN

MUSIC STREAMING

A2DP WORKS ONLY

ON F ONT SPEAKERS

1 2 3 4 5 6

Place DIP switch 1 to ON. (As shown below)

TO ENABLE VOICE DIAL:

NOTE:

If Voice Dial is enabled, the SWC function will change as follows:

1. A short press (tap) of the TUNE DOWN button will perform a “SEEK”.

2. A long press of the TUNE DOWN button will activate the Voice

Dial command on the paired phone.

Siri Voice command may not respond

properly. Standard Voice command

may have to be used instead.

BLUETOOTH CONNECTIVITY FOR SELECT CHRYSLER, DODGE VEHICLES 2011-UP

CHRYSLER

2011 - 2013 300

DODGE

2011 - 2014 Charger

2014 - 2014 Durango

2013 - 2014 Journey

Applications are subject to change

without notice.

BEECR-35C

Rev. 051315

MODELS LISTED BELOW MUST

BE EQUIPPED WITH SWC.

HOW TO ENTER THE MENU STRUCTURE

Preliminary:

on the mobile phone.

1. Hold Seek Down For 2 seconds on the SWC and release.

Note: to toggle between choices press seek down.

You are now at the top of the menu structure.

Here are your options:

a. Setting Volume - this controls the Beeline voice prompts.

To adjust the volume, press and release the volume +/ - buttons.

(In 1 second increments)

Press Seek Down to set the desired volume setting. There are a

total of 15 levels from the highest to lowest.

b. - this deletes all phones on the BeelineDelete Paired Phones

press the Seek Up button once. To cancel press Seek Down.

Note: The System Menu will time-out after 6 seconds of no activity.

If so, please begin at step one from above.

NOTES

Note: If an incoming call is answered from the mobile phone’s keypad, the call will direct itself to the headset on the mobile phone. To re-direct the

phone call to the “BEELINE”, it must be done directly from the mobile phone.