Használati útmutató Crunch CREQ7B

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Crunch CREQ7B (10 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 11 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/10
Operator’s Guide
CREQ7B
Thank you for purchasing the CRUNCH CREQ7B, 7-Band Equalizer/
two-way crossover. This unit has both a pre-amp equalizer and
crossover to provide the multi-speaker system of your vehicle with
improved sound performance. Please read the entire manual to
ensure proper connections and application.
CAUTION
Always consider consulting a professional audio installer
before installing any audio components. Be careful and take
your time. Do not let wires make contact with metal edges or
hot engine components.
Features
ILLUMINATED RED CONTROL KNOB LEDS
LOW AND HIGH LEVEL AUDIO INPUTS (SPEAKER LEVEL)
DESIGNATED SUBWOOFER UNBALANCED OUTPUT
SUBWOOFER X-OVER FREQUENCY CONTROL
INPUT LEVEL CONTROL ADJUSTMENT
FADER CONTROL
HALF DIN CHASSIS SIZE
MOUNTING HARDWARE (INCLUDED)
SEVEN EQUALIZATION BANDS EACH ADJUST +/- 12dB
1
Mounting and Hardware
Prior to mounting, connect the wires
to ensure proper operation.
MOUNTING
1. Select the desired mounting location, either under the dash or
in the dash. Make sure that there is adequate depth for the CREQ7B.
2. Use the mounting brackets and hardware provided. Make sure
there is proper clearance for the mounting bracket screws when
attaching under the dash. Use caution to ensure there are no wiring
harnesses behind the dash panel (where the mounting
screws are fastened).
3. Route the power, ground, and remote wires away from moving
parts to prevent pinching or shortened wires.
WIRING
1. : The power wire should connect to a constant or Power Wire
switched +12 volt source with a in-line fuse. We recommend (2 Amp)
that you use the radio constant or switch +12 volt source.
2. : Connect the ground wire to a clean chassis ground Gound Wire
point. Be sure to remove all paint and primer to expose clean metal.
Use a ring terminal and lock or star washer to secure the ground wire.
3. : The remote wire should be connected to the source Remote Wire
until remote or antenna wire that provides +12 volts when the
source unit is “on” and 0 volts when the source unit is turned “off.”
2

Termékspecifikációk

Márka: Crunch
Kategória: nincs kategorizálva
Modell: CREQ7B

Szüksége van segítségre?

Ha segítségre van szüksége Crunch CREQ7B, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva Crunch

Crunch

Crunch GP690 Útmutató

20 Szeptember 2024
Crunch

Crunch GP1000 Útmutató

9 Szeptember 2024
Crunch

Crunch GTi300T Útmutató

20 Augusztus 2024
Crunch

Crunch GTi250S Útmutató

20 Augusztus 2024
Crunch

Crunch CRXR Útmutató

10 Augusztus 2024
Crunch

Crunch CREQ7B Útmutató

8 Augusztus 2024
Crunch

Crunch GTS250 Útmutató

3 Augusztus 2024
Crunch

Crunch GTS350 Útmutató

2 Augusztus 2024
Crunch

Crunch GTS200 Útmutató

31 Július 2024
Crunch

Crunch CR1000CAP Útmutató

30 Július 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva