Használati útmutató Crestron DM-TX-4K-100-C-1G-B-T

Crestron AV hosszabbító DM-TX-4K-100-C-1G-B-T

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Crestron DM-TX-4K-100-C-1G-B-T (2 oldal) a AV hosszabbító kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

DO GUIDE

DO Install the Device

The DM-TX-4K-100-C-1G can be mounted into an electrical box, under a table, or onto a at

surface or rack rail.

Mounting into an Electrical Box

The DM-TX-4K-100-C-1G mounts into a 1-gang electrical box (not included). A minimum

mounting depth of 3-1/2 inches (89 mm) is required.

Using a Phillips head screwdriver, attach the DM-TX-4K-100-C-1G to the electrical box using

the two included 6-32 x 3/4-inch truss combo head screws. Then, attach a decorator-style

faceplate (not included) to the front panel of the DM-TX-4K-100-C-1G using two screws (not

included). Refer to illustration .

 Mounting into an Electrical Box

DM-TX-4K-100-C-1G

Wall Plate 4K DigitalMedia 8G+® Transmitter 100

DO Make Connections to the Rear Panel

Make connections to the rear panel of the Crestron® DM-TX-4K-100-C-1G before mounting the

unit into an electrical box. If the unit is to be mounted under a table or onto a at surface or rack

rail, make connections to the rear panel after the unit is mounted. (For mounting instructions,

refer to the “DO Install the Device” section in this guide.)

Make connections to the rear panel as follows:

DM OUT: Connect to the DM 8G+® input of a DigitalMedia™ switcher, DigitalMedia 8G+®

receiver, or other DigitalMedia device or to an HDBaseT® device.

NOTE: The DM OUT port is a PoDM (Power over DM) and HDBaseT® PoE (Power over Ethernet)

PD (Powered Device) port. To receive PoDM or HDBaseT PoE, the DM-TX-4K-100-C-1G requires

a connection to a DigitalMedia switcher or other equipment that has a PoDM or HDBaseT PoE

PSE (Power Sourcing Equipment) port. Any wiring that is connected to a PoDM or HDBaseT PoE

PSE port is for intrabuilding use only and should not be connected to a line that runs outside of

the building in which the PSE is located.

24VDC 0.75A: Connect to the included power pack using the included 2-pin interface

connector.

NOTE: Connection to the power pack is not required when PoDM or HDBaseT PoE is used to

power the device.

G: Connect to earth ground (building steel).

Refer to illustrations for sample rear panel connections.  and

 Connection to DigitalMedia Switcher Using PoDM

(External Power Pack Not Required)

DO Check the Box

QTY PRODUCT COLOR PART NUM.

1 Bracket (for Interface Module) Black 2016054

2 Connector, 2-Pin 2003574

1 Connector, 3-Pin 2003575

1 Power Pack, 24 Vdc 0.75 A, 100-240 Vac 2045866

2 Screw, 6-32 x 3/4", Truss Head, Combo 2009211

2 Screw, 6-32 x 1/4", Pan Head, SEMS Black 2007218

DM-RMC-4K-100-C

Ground

DM -R M C -4 K -1 0 0 -C

DM R OOM C ONT ROL LER

DB T

ASE

HDMI OUT

GND

TXRX

RTS

CTS

COM

LAN

DM IN

RESET

SETUP

24 V

0.75A MAX

Power

pack

 Connection to DigitalMedia Receiver

(External Power Pack Required)

DM-MD8X8

Ground

DO GUIDE DOC. 7551D (2042252) 12.16

Specicat ions subject t o change without not ice.

Mounting under a Table or onto a Flat Surface

The DM-TX-4K-100-C-1G mounts under a table or onto a

suitable at surface using the included surface mount bracket.

Using a Phillips head screwdriver, attach the included surface

mount bracket to the DM-TX-4K-100-C-1G using the two

included 6-32 x 1/4-inch SEMS screws. Then, attach the

bracket to the underside of a table or onto a at surface using

two mounting screws (not included). Refer to illustration .

 Mounting under a Table or onto a Flat Surface

Mounting onto a Rack Rail

The DM-TX-4K-100-C-1G mounts onto the front or rear rail of

a rack. Position the DM-TX-4K-100-C-1G horizontally so that

the holes in the left or right mounting ange align with the holes

in the rack rail. Then, secure the unit to the rack rail using two

mounting screws (not included). Refer to illustration .

 Mounting onto a Rack Rail

DO Make Connections to the Front Panel

Make connections to the front panel of the DM-TX-4K-100-C-1G

as required for the application.

HDMI IN: Connect to an HDMI® audio/video source.

IR OUT: Connect to the Crestron IRP2 emitter probe (not

included) using the included 2-pin connector.

COM: Connect to the device to be controlled using the

included 3-pin connector.1

Refer to illustration for sample front panel connections.

 Sample Front Panel Connections

1. The IR OUT port and the COM (RS-232) port are enabled only when the

DM-TX-4K-100-C-1G connects to an Ethernet-enabled DigitalMedia receiver

or switcher that is addressable from a Crestron control system.

DO Learn More

Visit the website for additional information and the

latest rmware updates. To learn more about this

product, use a QR reader application on your mobile

device to scan the QR image.

Crestron Electronics

15 Volvo Drive, Rockleigh, NJ 07647

888.CRESTRON | www.crestron.com

As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.

This product is Listed to applicable UL

® Standards and requirements by Underwriters Laboratories Inc.

Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the

user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

The s pecic patents t hat cover Crestron products are listed at . The product warrant y can be found at .patent s.crest ron.com www.crest ron.com/warranty

Certain Crestron products contain open source sof t ware. For specic information, please visit . www.crestron.com/opensource

Crest ron, the Crestron logo, DigitalMedia, DigitalMedia 8G +, and DM 8G+ are either trademarks or registered trademarks of Crestron Electronics, Inc. in t he United States and/or other count ries.

Blu-ray is either a trademark or regist ered trademark of the Blu-ray Disc Association in the United States and/or other countries. HDBaseT and the HDBaseT logo are eit her trademarks or

registered trademarks of t he HDBaseT Alliance in the Unit ed Stat es and/or other countries. HDMI and the HDMI logo are either trademarks or registered t rademarks of HDMI Licensing LLC

in the Unit ed States and/or other countries. UL and the UL logo are either trademarks or regist ered trademarks of Underwriters Laboratories, Inc. in the Unit ed States and/or other countries.

Ot her t rademarks, registered trademarks, and trade names may be used in t his document to refer to eit her the ent it ies claiming t he marks and names or t heir products. Crest ron disclaims any