Használati útmutató Creda MBO50

Creda Magnetron MBO50

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Creda MBO50 (3 oldal) a Magnetron kategóriában. Ezt az útmutatót 9 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/3

MBO50 & MBO55

BUILT-IN MICROWAVE OVENS

Installation Instructions

Retention of this Instruction Book...

This Instruction Book must be kept handy for reference as it contains important details on the safe and

proper use of the appliance.

If you sell or pass the appliance to someone else, or move house and leave it behind, make sure this Book

is also provided so the new owner can become familiar with the appliance and safety warnings.

Fig. 1

Fig. 1b

Fig. 2

Fig. 3 Fig. 4

Fig. 5

Fig. 7

Fig. 6

REINFORCEMENT STRIP

TO BE FITTED FLUSH TO

GRILL AS SHOWN

REINFORCEMENT STRIP

TO BE POSITIONED

CENTRALLY ON THE GRILL

(A) (B) (C)

(D) (E) (F)

(G) (H) (K) (L)

= +

= + (N)(J) 1x(F)

(M) (N)

Please read these instructions carefully before you begin

1. The microwave oven can be installed into a 600mm wide

Cabinet. The installation cavity must have the following

internal dimensions:

Height: 395mm (± 2mm)

Width: 562x570mm

Depth: At least 400mm

Vent: Min 45mm x 562mm applicable to all panels.

(Ensure the vent is not obstructed)

See Fig. 1.

2. The shelf must be able to support a weight of 15kg.

3. In the event of appliance failure, switch off the oven by

switching off at the wall switch and removing the mains plug

from the socket, or by isolating the supply from the main fuse-

box. Trim kit should be removed (see section E) prior to taking

out the oven from the cabinet.

Electrical Connections

The appliance is already fitted with a plug and may only be

connected to a correctly installed earthed socket. Only a qualified

electrician may install or relocate a socket outlet. The plug must be

accessible after installation unless an isolator switch is used to

disconnect all poles having a contact gap of at least 3mm in each

pole.

Contents

APaper template 1 piece

BCarrier rails 2 pieces

CFoam exhaust guide set 3 pieces

DBlanking plate 1 piece

EMetal exhaust guide 1 piece

FGrille 2 pieces

GSide trims 2 pieces

HScrews (short) 4 pieces

KScrews (long) 4 pieces

LCushions 2 pieces

MBlack Tape Strips 2 pieces

N Reinforcement Bracket 1 piece

JTop Grille (with metal strip) 1 piece

Please note that this part has to be assembled using 1 Grille (F)

and the Reinforcement Bracket (N). See Fig. 1b for assembly

instructions.

Also check that all the contents are available before

commencing work.

Preparing the cupboard for installation

1. Mark the centre of the cabinet shelf. Place the paper template

(A) onto the shelf, ensuring that the arrow on the template is

on the centreline and flush to the front leading edge of the

cabinet shelf.

2. Using a 3mm drill bit, pre-drill the 4 holes marked on the

template for attaching the carrier rails. When this is done

remove the template.

3. (A)Fold template along the dotted line, reposition the

template to the centre of the cabinet shelf and mark around

the corners. Once completed remove the template.

4. (B)Fit the carrier rails onto the cabinet shelf using the 4 small

screws provided (H) (Fig. 3).

5. Assemble the foam exhaust guide pieces together by inter-

locking the tabs into the holes, to obtain the assembly shown

(Fig. 2).

6. Peel the backing strip off the adhesive side of the assembled

exhaust guide, then fit it to the cabinet using the left hand

edge of the left carrier rail to align the one side, then use the

lines drawn on the cabinet to align the other remaining parts

of the exhaust guide.

N.B. Access will be required to accommodate the plug

top/mains cable.

Preparing the microwave oven for installation

1. Remove the 2 screws shown in from the underside of (Fig. 4)

the oven base below the door. Then use these screws to

attach the blanking plate to this area of the oven.(D)

2. Remove the screw at the rear right top of the oven (viewed

from behind the oven).

3. (L) Attach cushion strips to the front and rear flanges of the

oven exhaust guide (E). As shown in (Fig. 5).

4. (E)Hook the Oven exhaust guide into the rear panel of the

oven (see arrow - Fig. 5). Secure the Exhaust guide (E) onto

the rear panel of the oven using screw removed earlier. Then

fit black tape strips to the left and right flanges to seal this(M)

part to the top of the microwave oven. See (Fig. 5).

5. (B)Rest the microwave oven on the carrier rails . Plug the

power cord into the wall mains outlet via hole cut in the back

of the cabinet. Ensure that the feet of the oven are located

into the recesses.

N.B. Care should be taken when fitting the microwave oven,

so as not to pinch the foam pieces and the power cord during

installation. Therefore an assistant may be required.

Attaching the Plastic Grilles and Side Trims

1. Centralise and align the frame pieces to the front of the

cabinet and mark the position of the screw holes, and then

drill holes using a 3mm drill bit.

2. Loosely attach the top and bottom grille pieces (F/J) to the

front of the cupboard using the screws provided as shown(K)

in (Fig. 6). Ensure that grille piece J is fitted at the top.

3. Hold the side trim pieces (G) against the oven and align the

top and bottom grill vents . Ensure there is an equal gap (F/J)

between the oven and the trim pieces.

4. Tighten up the screws (K).

5. Press and clip the side trims (G) into place, between the top

and bottom grills on the edge of the cabinet.

Removing the Plastic Grills and Side Trims

Insert a flat bladed screwdriver into the slot of the side trim pieces

(G) and prise them off. See . Remove the screws fixing the(Fig. 6)

top and bottom grill vent pieces. Ensure that the screwdriver does

not slip as to avoid causing damage to the side trim pieces.

Termékspecifikációk

Márka:	Creda
Kategória:	Magnetron
Modell:	MBO50

Szüksége van segítségre?

Ha segítségre van szüksége Creda MBO50, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Magnetron Creda

4 Április 2025

27 Augusztus 2024

27 Augusztus 2024

27 Augusztus 2024

27 Augusztus 2024

26 Augusztus 2024

26 Augusztus 2024

26 Augusztus 2024

26 Augusztus 2024

26 Augusztus 2024

Útmutatók Magnetron

Legújabb útmutatók Magnetron

Whirlpool AMW4910IX Útmutató

10 Április 2025

Sanyo ems 1052 Útmutató

10 Április 2025

Panasonic NE552 Útmutató

10 Április 2025

Sanyo em s1050 Útmutató

9 Április 2025

Panasonic nn sd 278 sepg Útmutató

9 Április 2025

Whirlpool AVM 686 Útmutató

7 Április 2025

Samsung MS22M8074 Útmutató

7 Április 2025

Whirlpool at 314 Útmutató

6 Április 2025

Privileg PCMF 222220 X Útmutató

6 Április 2025

Koenig Microwave 2000 Útmutató

6 Április 2025