Használati útmutató Cisco RV260W

Cisco router RV260W

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Cisco RV260W (12 oldal) a router kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/12
Quick Start Guide
Cisco RV260W Router
Cisco RV260W Router
Cisco RV260W Router
Cisco RV260W RouterCisco RV260W Router
Package Contents
Cisco RV260W Router
Universal Power Adapter
This Quick Start Guide
Pointer Card/RoHS
Technical Support Contact Card
Ethernet Cable
EU Directives 2014/53/EU Compliance Information (for EU SKU only)
2 Cisco RV260W Router Quick Start Guide
Welcome
Thank you for choosing the Cisco RV260W router.
The RV260W router provides reliable Internet access connectivity and
includes the following features:
Easy to use UI with multiple set-up wizards.
Eight port wireless router.
Supports IPv6 firewall.
Business-grade small business network in a box.
This guide describes how to install your Cisco RV260W and launch the
web-based Device Manager.
Installing the Cisco RV260W
To prevent the device from overheating or being damaged:
Ambient Temperature — Do not operate the device in an area that
exceeds an ambient temperature of 104°F (40°C).
Air Flow Be sure that there is adequate airflow around the device. If
wall mounting the device, make sure that the heat dissipation holes are
to the side.
Circuit Overloading Adding the device to the power outlet must not
overload that circuit.
Mechanical Loading Be sure that the device is level and stable to
avoid any hazardous conditions and that it is secure to prevent it from
sliding or shifting out of position. Do not place anything on top of the
device, as excessive weight may damage it.
Desktop Mounting
For desktop mounting, place the device on a flat surface so that it sits on its
four rubber feet.
Wall Mounting
The RV260W router has two wall-mount slots on the bottom panel. To
mount the router on a wall, you will need to use the wall-mount kit screws
(included).
Guidelines for Mounting the Router on a Wall
When choosing a location for mounting the router on a wall, consider cable
limitations and wall structure.
1
Cisco RV260W Router Quick Start Guide 3
Mount the router with the front panel facing upward. Make sure to mount
the router low enough so that you can see the LEDs.
Make sure that the power supply rests on a horizontal surface such as
the floor or a table. If the power supply is not supported, the strain on
the power adapter cable could cause it to disconnect from the router.
Do not install the router or its power supply next to a heat source of any
kind, including heating vents.
You can mount the router on a hollow wall or a wall stud. To mount the
router, follow these steps:
S 1TEP Position the router on the wall to determine where to attach the two
mounting screws. Drill two pilot holes at approximately 109 mm
apart.
S 2TEP Insert a screw into each hole, leaving a gap between the surface
and the base of the screw head of 1 to 1.2 mm.
S 3TEP Place the router wall-mount slots over the screws and slide the
router down until the screws fit snugly into the wall-mount slots.
WARNING Insecure mounting might damage the router or cause injury.
Cisco is not responsible for damages incurred due to insecure
wall-mounting.
WARNING For safety reasons, please ensure that the heat dissipation
holes are facing sideways.

Termékspecifikációk

Márka: Cisco
Kategória: router
Modell: RV260W

Szüksége van segítségre?

Ha segítségre van szüksége Cisco RV260W, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók router Cisco

Cisco

Cisco DPC2320 Útmutató

2 Október 2024
Cisco

Cisco RV042G Útmutató

18 Szeptember 2024
Cisco

Cisco C927-4PM Útmutató

2 Szeptember 2024
Cisco

Cisco C1121-4PLTEP Útmutató

24 Augusztus 2024
Cisco

Cisco 4351 Útmutató

23 Augusztus 2024
Cisco

Cisco 910 Útmutató

23 Augusztus 2024
Cisco

Cisco WES610N Útmutató

3 Augusztus 2024
Cisco

Cisco 7204VXR Útmutató

3 Augusztus 2024
Cisco

Cisco 3845 Útmutató

2 Augusztus 2024

Útmutatók router

Legújabb útmutatók router