Használati útmutató Chimera OctaPlus 57

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Chimera OctaPlus 57 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/2
Lightbank Assembly for the
OctaPlus 3 and
OctaPlus5
Insert Poles into Pole Sleeves- Insert rounded
pole-ends into pole sleeves
located in inside “corners” of
the OctaPlus™ Lightbank.
Guide each pole carefully
through the pole sleeve until it
is snug at the opposite end of
the sleeve. Note: On the
OctaPlus 5™, the adaptor tips for the OctaPlus
57™ will push through the
grommet hole and be exposed
(see details on next page).
Mount Your OctaPlus™ Ring on the Stand – We strongly recommend that a stand adapter
(CHIMERA® model #3770) be used with the OctaPlus 5 and 57™ Lightbanks so that the weight is
not supported by the lighting instrument. A stand adapter, while helpful, is not essential for the
OctaPlus 3™ Lightbank. Mount your Speed Ring to the light stand using the 3770 stand adaptor or
the mounting method of your choice. For your safety and the security of your lighting instrument, if
at all possible, mount your lighting instrument to the OctaPlus™ Ring after mounting the assembled
OctaPlus™ Lightbank on the stand.
Erect the OctaPlus™ on the OctaPlus™ Ring- Start with one of upper holes; insert
exposed pole-end extending from Lightbank into hole on outside edge of Speed Ring. Pole
ends must be seated fully in bottom of holes. Repeat the pole insertion until all the poles are in
place. Many users feel it is easiest to insert the poles directly opposite each other. This helps
even out the tension on the OctaPlus™ Lightbank as it is assembled.
Install the Baffle and Front Screen – The interior baffle is attached to the inside of the
OctaPlus™ Lightbank just in front of the lighting instrument. Attach one of the Velcro® tabs on
the baffle to one of the Velcro® tabs on the pole sleeves. The next
attachment should be made directly opposite the first. Continue with the
attachment of the tabs working in this opposite attachment method until all
eight tabs are installed. Working in this method will assure a much tighter
fitting baffle for more even light distribution. Reposition the tabs, if
necessary, to make sure the baffle is centered in the OctaPlus™ Lightbank.
When installing the front screen, the CHIMERA® label should be facing
the outside. Take one of the eight sides of the front screen and line the
“back” edge of the Velcro® hook up with the back edge of the Velcro®
pile strip just inside the front of the OctaPlus™ Lightbank. Press the
two strips together and then move to the next edge of the front screen
and line it up the same way. Continue attaching the edges in a circular
fashion around the Lightbank. Keep the front screen as taut and smooth as possible for the
best possible light distribution.
Removing OctaPlus™ from the OctaPlus™ Ring - - Allow the light to cool completely
before removing the OctaPlus™ Lightbank. For longest life, remove the front screen and baffle
from the OctaPlus™ Lightbank and fold them neatly. Starting with one of the poles, grasp pole
in palm of hand and place thumb on the OctaPlus™ Ring. Grip the pole on opposite side with
your other hand for additional leverage. Apply backward pressure on pole to center it in its
mounting hole and slide to pole out of the hole. Repeat until all poles are free.
OctaPlus Lightbank Care and Use Instructions
Folding and Storing the OctaPlus™ Lightbank - Once the OctaPlus™ Lightbank is removed from
the OctaPlus™ Ring, fold it flat then fold it over again. Roll the Lightbank into a tight cylinder and place it in
the storage sack along with the other components. You may choose to leave the poles in place in the
OctaPlus™ Lightbank. If you are storing the OctaPlus™ Lightbank for a greater length of time it is better to
remove the poles. Make sure your CHIMERA® OctaPlus™ Lightbank is not wet, damp or soiled
before storing.
CHIMER OctaPlus 57™ Care and Use Instructions
Adding the OctaPlus 57™ Extension Kit – Assemble the OctaPlus 5™
Lightbank according to the instructions above (with or without the front screen
depending on the diffusion preferred). Then begin the OctaPlus 57™ assembly
by slipping the OctaPlus 57™ extension poles into the extension skirt pole
sleeves. Make sure the end with the rounded tip is in front.
Once all of the poles are in their sleeves, fit the rear end of the
OctaPlus 57™ extension poles over the adapter tips of the
OctaPlus 5™ poles protruding through the grommet holes. It
is easiest to start at the top of the OctaPlus™ Lightbank and
work your way to the bottom, moving back and forth as you
go. Once the poles are assembled, press the Velcro® strips between the OctaPlus 5™
and OctaPlus 57™ skirt together to seal the OctaPlus 57™ Lightbank into one unit.
Then, seal the Velcro® straps at each extension pole intersection.
Next, add the OctaPlus 57™ front screen using the front screen instructions above. Most of the time users
remove and store the OctaPlus 5™ front screen; however there may be times when you prefer to use the
OctaPlus 5™ front screen in combination with the OctaPlus 57™ front screen for an extra soft light.
CAUTION NOTES:
This is a professional product for use in moderate temperature environments. Failure to
follow these safety precautions could create a hazardous condition.
Do not leave Lightbank unattended while in use.
Open top and bottom flaps completely to allow air flow.
Excessive heat and/or moisture may damage Lightbank.
Do not use Lightbank in wet conditions.
Always use light fixture’s protective screen. Screen must be of fine mesh size to prevent hot shards of
glass or quartz from contacting Lightbank in event of bulb explosion. Damage or fire caused by
exploding bulb is not covered by CHIMERA® warranty.
Please visit the CHIMERA® web site, www.chimeralighting.com, for additional care, use and repair
information.
CHIMERA
CHIMERA
CHIMERA
CHIMERACHIMERA® 1812 VALTEC LANE, BOULDER, COLORADO 80301 USA
TOLL FREE 888-444-1812 PHONE 303-444-8000 FAX 303-444-8303
EMAIL: salesinfo@chimeralighting.com WEB SITE: www.chimeralighting.com

Termékspecifikációk

Márka: Chimera
Kategória: nincs kategorizálva
Modell: OctaPlus 57

Szüksége van segítségre?

Ha segítségre van szüksége Chimera OctaPlus 57, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva Chimera

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva