Használati útmutató Chief RSA315

Chief Lapos panel támogatás RSA315

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Chief RSA315 (2 oldal) a Lapos panel támogatás kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
8850-000158 Rev03
©2010 Milestone AV Technologies,
a Duchossois Group Company
11/10
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
I N S T A L L A T I O N I N S T R U C T I O N S
SSB-315, SSM-315, SLB-315 and SLM-315 Interface Brackets
SSB-315, SSM-315, SLB-315 and SLM-315 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
continued....
(1) Interface Bracket (3) Screw, Phillips Flat Head, Machine, M3 x 16mm
(4) 10-24 Thumb Nuts ** (3) Screw, Phillips Flat Head, Machine, M3 x 20mm
(1) All-Points Security Kit (3) Spacer, Black, .375" x .171" x .4375"
(6) Spacer, White, .375" x .194" x .3125"
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations
above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interfac
e bracket installation.
Note: SSB-style interface bracket connections are circled. Note: SSM-style interface bracket connections are circled.
SLB-315 SLM-315
Towards front
of projector Towards front
of projector
I N S T A L L A T I O N I N S T R U C T I O N S
Continued....
IMPORTANT ! : Some projector models may not be listed at this time. Follow instructions for the various install options after
you have determined which option matches your projector model.
WARNING: IF A BRACKET IS TOO LOOSE THE PROJECTOR COULD BE DAMAGED OR A FASTENER COULD BE TWISTED
OFF. If a bracket seems loose, move to try the next installation option.
3. Verify if your projector model is listed for a recommended install option. If your projector model is NOT listed, start with Option 1 and
work through options one at a time.
4. Place the correct spacers according to the option for your projector model.
• OPTION 1: Center three .3125" white spacers over three threaded inserts in bottom of projector.
• : Center three .4375" black spacers over three threaded inserts in bottom of projector.OPTION 2
• OPTION 3: Use six .3125" white spacers, double-stacked, and place over three threaded inserts in bottom of projector.
5. Place interface bracket on top of spacers aligning the mounting holes in the interface bracket with the holes in the spacers.
6. Select the correct fasteners according to the option for your projector model.
• OPTION 1 : Use three M3 x 16mm screws and secure interface bracket to projector by threading screws through bracket and spacers
and into threaded inserts in bottom of projector.
• OPTION 2 : Use three M3 x 16mm screws and secure interface bracket to projector by threading screws through bracket and spacers
and into threaded inserts in bottom of projector.
• OPTION 3: Use three M3 x 20mm screws and secure interface bracket to projector by threading screws through bracket and spacers
and into threaded inserts in bottom of projector.
7. Tighten all fasteners at this time, securing the bracket to the projector.
Projector Models
Option 1 DELL® Models 2300MP, 5100MP
Option 2 DELL Models: 2100MP, 2200MP, 3200MP, 3300MP
HP® Models: sb21, xb31
Optoma® Models: H30,EP731,EP732,EP732B, EP732E,EP732H, EP737
Option 3 DELL Model 4100MP

Termékspecifikációk

Márka: Chief
Kategória: Lapos panel támogatás
Modell: RSA315

Szüksége van segítségre?

Ha segítségre van szüksége Chief RSA315, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Lapos panel támogatás Chief

Chief

Chief MWCU Útmutató

3 Április 2025
Chief

Chief KITXWXSM1U Útmutató

3 Április 2025
Chief

Chief RLXT3 Útmutató

3 Április 2025
Chief

Chief MIWRFUB Útmutató

16 Január 2025
Chief

Chief TILD1X5NE1-M Útmutató

16 Január 2025
Chief

Chief TILD1X3NE1-R Útmutató

16 Január 2025
Chief

Chief TILD1X4NE1-L Útmutató

16 Január 2025
Chief

Chief PWRIWUB Útmutató

16 Január 2025
Chief

Chief RSMBU Útmutató

29 December 2024
Chief

Chief RPA640 Útmutató

29 December 2024

Útmutatók Lapos panel támogatás

Legújabb útmutatók Lapos panel támogatás

Konig

Konig KNM-MM20 Útmutató

8 Április 2025
Ergotron

Ergotron Neo-Flex Widescreen Stand Útmutató

3 Április 2025
Ergotron

Ergotron Neo-Flex Cantilever Útmutató

3 Április 2025
Ergotron

Ergotron All-In-One Lift Stand Útmutató

3 Április 2025
Ergotron

Ergotron DS100 Dual Monitor Desk Stand Útmutató

3 Április 2025
Ergotron

Ergotron DS Series DS100 Quad Monitor Desk Stand, Horizontal Útmutató

3 Április 2025
Ergotron

Ergotron LX Series Desk Mount LCD Arm, Tall Pole Útmutató

3 Április 2025
Ergotron

Ergotron LX Series Dual Stacking Arm Útmutató

3 Április 2025
Ergotron

Ergotron 100 Series Double Pivot Útmutató

3 Április 2025
Ergotron

Ergotron Convert-to-LCD & Laptop Kit Útmutató

3 Április 2025