Használati útmutató Chief PRO2000B

Chief Lapos panel támogatás PRO2000B

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Chief PRO2000B (6 oldal) a Lapos panel támogatás kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/6
I N S T A L L A T I O N I N S T R U C T I O N S
Large Flat Panel Wall Mount
Model: PRO-2000 Series
PRO-2000 Series Wall Mount Features:
• Accommodates large flat screens weighing up to
200 lbs (90.7 kg).
• Mounting brackets adapt to either 16" or 24" on
center dual stud wood framework; integrated
lateral shift adjusts ± 4.5" (16" on center) or ± 0.5"
(24" on center).
• Infinite tilt and lock adjustment between 0-15
degrees.
• Chief's exclusive Q-Latch mounting system
provides convenient and secure display connect/
disconnect; optional padlock provides additional
display security.
Q-Latch® is a registered trademark of Chief Mfg.
! IMPORTANT: If the installation of this product requires
OSHPD seismic approval, refer to OSHPD pre-approval
documents and drawings before beginning installation.
OSHPD documents and drawings are available at
www.chiefmfg.com, and are also located on the product
information page for the mount. PRO-2000 Series
BEFORE YOU BEGIN
CAUTION: To prevent damage to your monitor and PRO-2000, which could affect or void the Factory warranty,
thoroughly study all instructions and illustrations before you begin to install the mount. Pay particular attention to the
Warnings and Cautions in this document.
• The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor
the mount must be capable of supporting five times the total weight of the equipment.
• The maximum weight to be installed on the PRO-2000 wall mount is 200 lbs (90.7 kg).
• If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-
6480.
CHIEF MANUFACTURING INC.
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PARKWAY, STE 700
SAVAGE, MINNESOTA 55378 USA
8805-000140 (Rev. E)
2007 Chief Manufacturing
www.chiefmfg.com
10/07
Installation Instructions
2
IMPORTANT WARNINGS AND CAUTIONS!
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: It is the installer’s responsibility to make sure structure to which this mount is attached can support five
times the combined weight of all equipment. Reinforce the structure as required before installing the accessory.
Failure to provide adequate structural strength for the mount can result in serious personal injury or damage to
equipment!
WARNING: It is the installer’s responsibility to make sure all components are properly assembled and installed using
instructions provided. Failure to follow instructions can result in serious personal injury or damage to equipment!
WARNING: It is the installer’s responsibility to make sure combined weight of mount, display, and all attached
equipment must not exceed 200 lbs (90.7 kg), the maximum support weight of this mount. Exceeding maximum
support weight can result in serious personal injury or damage to equipment!
WARNING: Watch for pinch points. Do not put your fingers between movable parts.
WARNING: Make sure the Q-Latches securing the display are fully latched at all times except when removing or
installing the display. The Q-Latches must be fully latched when installing/removing cables.
CAUTION: Check the unit for shipping damage before you begin the installation.
DIMENSIONAL DRAWING
Installation Instructions
3
TOOLS REQUIRED FOR INSTALLATION
• Drill and drill bit set
• Socket wrench set
NOTE: Other tools may be required depending on your method of installation.
PARTS
Unpack carton, inspect and verify contents.
Read installation instructions completely. If any listed
parts are missing, contact Chief Customer Service at
1-800-582-6480.
Table 1: Parts
10 MOUNT, PRO-2000 Series 1
20 BOLT, Lag, 5/16" x 2-½" 4
30 WASHER, 5/16" 4
10
20 - 4 Lag Bolts
30 - 4 Washers

Termékspecifikációk

Márka: Chief
Kategória: Lapos panel támogatás
Modell: PRO2000B

Szüksége van segítségre?

Ha segítségre van szüksége Chief PRO2000B, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Lapos panel támogatás Chief

Chief

Chief MWCU Útmutató

3 Április 2025
Chief

Chief KITXWXSM1U Útmutató

3 Április 2025
Chief

Chief RLXT3 Útmutató

3 Április 2025
Chief

Chief MIWRFUB Útmutató

16 Január 2025
Chief

Chief TILD1X5NE1-M Útmutató

16 Január 2025
Chief

Chief TILD1X3NE1-R Útmutató

16 Január 2025
Chief

Chief TILD1X4NE1-L Útmutató

16 Január 2025
Chief

Chief PWRIWUB Útmutató

16 Január 2025
Chief

Chief RSMBU Útmutató

29 December 2024
Chief

Chief RPA640 Útmutató

29 December 2024

Útmutatók Lapos panel támogatás

Legújabb útmutatók Lapos panel támogatás

Konig

Konig KNM-MM20 Útmutató

8 Április 2025
Ergotron

Ergotron Neo-Flex Widescreen Stand Útmutató

3 Április 2025
Ergotron

Ergotron Neo-Flex Cantilever Útmutató

3 Április 2025
Ergotron

Ergotron All-In-One Lift Stand Útmutató

3 Április 2025
Ergotron

Ergotron DS100 Dual Monitor Desk Stand Útmutató

3 Április 2025
Ergotron

Ergotron DS Series DS100 Quad Monitor Desk Stand, Horizontal Útmutató

3 Április 2025
Ergotron

Ergotron LX Series Desk Mount LCD Arm, Tall Pole Útmutató

3 Április 2025
Ergotron

Ergotron LX Series Dual Stacking Arm Útmutató

3 Április 2025
Ergotron

Ergotron 100 Series Double Pivot Útmutató

3 Április 2025
Ergotron

Ergotron Convert-to-LCD & Laptop Kit Útmutató

3 Április 2025