Használati útmutató Chief PLP2000B

Chief Lapos panel támogatás PLP2000B

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Chief PLP2000B (8 oldal) a Lapos panel támogatás kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/8
CHIEF MANUFACTURING INC. 8805-000183 Rev F
1-800-582-6480 952-894-6280 FAX 952-894-6918 ©2008 Chief Manufacturing
8401 EAGLE CREEK PARKWAY, STE. 700 www.chiefmfg.com
SAVAGE, MINNESOTA 55378 USA 03/08
I N S T A LL A T I O N IN S T R U C T IO N S
PLP Series Wall Mount
The PLP Series wall mount accommodates large flat
screens weighing up to 200 lbs (90.72kg). The teardrop
holes in the mount allow for quick connect/disconnect of
the screen, thus simplifying installation and maintenance
processes.
The top and bottom mounting brackets are adaptable to
supporting framework with wood studs that are 16” on
center or 24”on center.
The mount has integrated lateral shift, allowing for four
different mounting options. For dual wood studs 16” on
center, the lateral shift is + 4.5 inches. For dual wood
studs 24” on center, the lateral shift is + 0.5 inches.
The display can be pulled and tilted by hand into any
position in the zero-to-15 degree tilt range and remain
stationary.
The bottom of the mount pulls forward 4” from the wall
and locks into place for installation of cable connections.
The mount also uses Chief’s exclusive Q-Latch™
mounting system, which offers quick connect/disconnect
display mounting. The display is secured to the mount
with a latching flag. For additional security, you can lock
the latching flag in place by adding a padlock. PLP Series
Installation Instructions PLP Series
2
! IMPORTANT: If the installation of this product requires OSHPD seismic approval, refer to OSHPD pre-approval
documents and drawings before beginning installation. OSHPD documents and drawings are available at
www.chiefmfg.com, and located on the product information page for the mount.
BEFORE YOU BEGIN
CAUTION: To prevent damage to your monitor and PLP, which could affect or void the Factory
warranty, thoroughly study all instructions and illustrations before you begin to install the mount. Pay
particular attention to the Warnings and Cautions in this document.
The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor the
mount must be capable of supporting five times the total weight of the equipment.
The maximum weight to be installed on the PLP Series wall mount is 200 lbs (90.72kg).
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-
6480.
IMPORTANT WARNINGS and CAUTIONS!
WARNING A WARNING alerts you to the possibility of serious injury or death if you do not
follow the instructions.
CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do
not follow the corresponding instructions.
WARNING Improper installation can result in serious personal injury! Make sure that the
structural members can support a redundant weight factor five times the total weight
of the equipment. If not, reinforce the structure before installing the mount.
WARNING Be aware of the potential for personal injury or damage to the equipment if it is not
installed correctly. Consider the weight of the mount without the display.
WARNING The installer is responsible for verifying that the display to which the wall mount is
fastened will safely support the combined load of all attached components or other
equipment.
WARNING The combined weight of the display placed on the wall mount must not exceed 200 lbs
(90.72kg),the maximum support weight of the mount.
WARNING Watch for pinch points. Do not put your fingers between movable parts.
WARNING Make sure the flag securing the display is completely lowered at all times except when
removing or installing the display. The flag must be all the way down when
installing/removing cables.
CAUTION Check the unit for shipping damage before you begin the installation.
Installation Instructions PLP Series
3
DIMENSIONAL
DRAWING
17.00
.69
1.87
4.24
15.51
18.38
13.19
16.00
16.00
16.00
24.00
5/16" x 1" SLOT
5/16" x 6" SLOT
5/16" x 1" SLOT
TOP MOUNTING BUTTON ON
PSB-XXXX DRAWING GOES HERE
26.00
1.83
FACE TILTS
15 DOWN
7 UP (FOR SERVICE)
NOTE: CUSTOM INTERFACE BRACKET
NOT SHOWN. THE CUSTOM INTERFACE
BRACKET NEEDED FOR YOUR DISPLAY
WILL ADD BETWEEN 1/2" AND 2" IN DEPTH
AND MAY AFFECT LOCATION OF DISPLAY
ON THE MOUNT.
SEE PSB-XXXX DRAWING ALSO.
C

Termékspecifikációk

Márka: Chief
Kategória: Lapos panel támogatás
Modell: PLP2000B

Szüksége van segítségre?

Ha segítségre van szüksége Chief PLP2000B, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Lapos panel támogatás Chief

Chief

Chief MWCU Útmutató

3 Április 2025
Chief

Chief KITXWXSM1U Útmutató

3 Április 2025
Chief

Chief RLXT3 Útmutató

3 Április 2025
Chief

Chief MIWRFUB Útmutató

16 Január 2025
Chief

Chief TILD1X5NE1-M Útmutató

16 Január 2025
Chief

Chief TILD1X3NE1-R Útmutató

16 Január 2025
Chief

Chief TILD1X4NE1-L Útmutató

16 Január 2025
Chief

Chief PWRIWUB Útmutató

16 Január 2025
Chief

Chief RSMBU Útmutató

29 December 2024
Chief

Chief RPA640 Útmutató

29 December 2024

Útmutatók Lapos panel támogatás

Legújabb útmutatók Lapos panel támogatás

Konig

Konig KNM-MM20 Útmutató

8 Április 2025
Ergotron

Ergotron Neo-Flex Widescreen Stand Útmutató

3 Április 2025
Ergotron

Ergotron Neo-Flex Cantilever Útmutató

3 Április 2025
Ergotron

Ergotron All-In-One Lift Stand Útmutató

3 Április 2025
Ergotron

Ergotron DS100 Dual Monitor Desk Stand Útmutató

3 Április 2025
Ergotron

Ergotron DS Series DS100 Quad Monitor Desk Stand, Horizontal Útmutató

3 Április 2025
Ergotron

Ergotron LX Series Desk Mount LCD Arm, Tall Pole Útmutató

3 Április 2025
Ergotron

Ergotron LX Series Dual Stacking Arm Útmutató

3 Április 2025
Ergotron

Ergotron 100 Series Double Pivot Útmutató

3 Április 2025
Ergotron

Ergotron Convert-to-LCD & Laptop Kit Útmutató

3 Április 2025