Használati útmutató Chief FDP4100B

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Chief FDP4100B (2 oldal) a Lapos panel támogatás kategóriában. Ezt az útmutatót 10 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/2
8803-000033 01/26/04
CHIEF MANUFACTURING INC. 1-800-582-6480, Fax: 1-877-894-6918, Email: chief@chiefmfg.com
INSTALLATION INSTRUCTIONS
FDP SERIES
SMALL FLAT PANEL DISPLAY
DUAL SCREEN POLE MOUNT
Exclusive Q2™ Mounting System
Prior to assembly, unpack carton completely and verify contents.
If you are missing any of the following components, please contact Customer Service at 1-800/582-6480.
(2) FDP Pole-Mounting Bracket Half (2) ¼” Flat Washer
(2) ¼-20 X 4.25” Hex Bolt (8) 10-24 X 1.00 Thread Forming Screw
(8) ½” X ½” Nylon Spacer
BEFORE PROCEEDING, READ INSTALLATION INSTRUCTIONS COMPLETELY
The FSP will fit on any 1/1/2” to 2 O.D. pipe including 1 ½”NPT.
Flat Panel Displays are Extremely Fragile.
If Monitor Uses a Screw Size Other Than M4 X 10mm (M4 X 20mm),
DO NOT USE M4 Screws Provided. Monitor Damage Could Occur.
Interface Bracket Installation:
1. See installation procedures accompanying your mounting bracket.
Optional Latching Flag Placement:
1. Remove Phillips head screw, Nylock nut and latching flag (see Figure 2).
2. Reposition latching flag and secure using Phillips head screw, Nylock nut.
Figure 1
Figure 2
CAUTION!
Remove screw
and nu
t
M
ove
l
atc
h
8803-000033 01/26/04
CHIEF MANUFACTURING INC. 1-800-582-6480, Fax: 1-877-894-6918, Email: chief@chiefmfg.com
Pole-Mounting Bracket Assembly and Installation:
1. Assemble two pole-mounting bracket halves as shown in Figure 3 and secure using two ¼-20 X 4.25”
hex bolts and two ¼” flat washers.
2. For vertical pole mounting, install the pole-mounting bracket on 1 ½” to 2” OD pipe/pole and secure
using 7/16” hex drives (see Figure 4).
3. For horizontal pole mounting; remove eight tilt adjustment screws, reposition the tilt bracket as
shown in Figure 5, and insert nylon spacers. Secure using 10-24 x 1.00 screws provided.
Mounting Display with Interface Bracket to Pole-Mounting Bracket:
1. Make sure both latching flags on pole-mounting bracket are in the unlocked position (see Figure 4).
2. Place your small flat panel displays; with interface brackets attached, onto the pole-mounting bracket,
making sure they are securely seated.
3. Engage pole-mounting bracket latching flags, locking small flat panel displays in place (see Figure 6).
4. Adjust tilt by loosening (slightly) tilt adjustment screws (see Figure 7) on each side of pole-mounting
bracket, adjust to desired angle, and tighten tilt adjustment screws.
Figure 3 Figure 4
Locked
Unlocked
Tighten to
secure to
p
ole
Tilt
Adjustment
Screws
Figure 6
10-24 x 1.00 screw
.500 O.D. x .500
long nylon spacer
Figure 7
¼-20 X 4.25” hex bolt
and ¼” washer
Figure 5

Termékspecifikációk

Márka: Chief
Kategória: Lapos panel támogatás
Modell: FDP4100B

Szüksége van segítségre?

Ha segítségre van szüksége Chief FDP4100B, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Lapos panel támogatás Chief

Chief

Chief MWCU Útmutató

3 Április 2025
Chief

Chief KITXWXSM1U Útmutató

3 Április 2025
Chief

Chief RLXT3 Útmutató

3 Április 2025
Chief

Chief MIWRFUB Útmutató

16 Január 2025
Chief

Chief PWRIWUB Útmutató

16 Január 2025
Chief

Chief RSMBU Útmutató

29 December 2024
Chief

Chief RPA640 Útmutató

29 December 2024

Útmutatók Lapos panel támogatás

Legújabb útmutatók Lapos panel támogatás