Használati útmutató Carel MasterCase

Carel nincs kategorizálva MasterCase

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Carel MasterCase (60 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/60
MasterCase
User manual
We wish to save you time and money!
We can assure you that the thorough reading of this manual will guarantee correct installation and
safe use of the product described.
BEFORE INSTALLING OR HANDLING THE DEVICE PLEASE CAREFULLY READ AND FOLLOW THE
INSTRUCTIONS DESCRIBED IN THIS MANUAL.
This device has been manufactured to operate risk-free for its specific purpose, as long as:
it is installed, operated and maintained according to the instructions contained in this manual;
the environmental conditions and the voltage of the power supply correspond to those specified.
All other uses and modifications made to the device that are not authorised by the manufacturer are considered incorrect.
Liability for injury or damage caused by the incorrect use of the device lies exclusively with the user.
Please note that this unit contains powered electrical devices and therefore all service and maintenance operations must be
performed by specialist and qualified personnel who are aware of the necessary precautions.
Disconnect the machine from the mains power supply before accessing any internal parts.
Disposal of the parts of the controller:
The controller is made up of metal and plastic parts and contains a lithium battery. All these parts must be disposed of
according to the local standards in force.
General warnings - operating environments and connections
The following conditions represent correct installation:
1. do not install the instrument in environments with the following characteristics: wide and rapid fluctuations in ambient
temperature; temperature and relative over the allowed limit; exposure to direct pressurised jets of water; high levels of
magnetic and/or radio frequency interference (e.g. from transmitting antennae);
2. use cable ends suitable for the corresponding terminals. Loosen each screw and insert the cable ends, then tighten the screws.
When the operation is completed, slightly tug the cables to check that they are sufficiently tight;
3. separate as much as possible the signal cables from the cables carrying inductive loads and power cables to avoid possible
electromagnetic disturbance. Never insert power cables (including the electrical cables) and probe signal cables in the same
conduits. Do not install the probe cables in the immediate vicinity of power devices (contactors, circuit breakers or similar);
4. reduce the path of the probe cables as much as possible, and avoid spiral paths that enclose power devices. To extend the
probe cables, use cables with a minimum cross-section of at least 0.5mm2;
5. the cables connected to the contacts on the controller must be rated for the maximum operating temperature, determined by
considering the maximum room temperature envisaged, added to the heating up of the controller itself, equal to 20°C;
6. suitably protect the load power lines on the controller with devices (circuit breakers) rated according to the loads connected.
Safety for operators and precautions when handling the controller
To protect the safety of operators and safeguard the controller, before doing any work on the panel always disconnect the power
supply. Electrical damage may occur to the electronic components as a result of electrostatic discharges from the operator.
Suitable precautions must be therefore be taken when handling these components, specifically:
• before handling any controller, earth yourself (not touching the board does not prevent a spike, as a 10000V discharge, easily
reached with static electricity, can produce an arc of about 1cm);
• all materials must be kept inside their original package as long as possible. If necessary, take the controller from its package
and place it into an antistatic package without touching the rest of the controller with your hands;
• absolutely avoid non-antistatic plastic bags, polystyrene or sponges;
• do not pass the controller directly to other operators (to prevent from electrostatic induction and discharges).

Termékspecifikációk

Márka: Carel
Kategória: nincs kategorizálva
Modell: MasterCase

Szüksége van segítségre?

Ha segítségre van szüksége Carel MasterCase, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók nincs kategorizálva Carel

Carel

Carel Hecu Útmutató

31 December 2025
Carel

Carel µChiller process Útmutató

14 Október 2024
Carel

Carel iJF Útmutató

17 Szeptember 2024
Carel

Carel SmartCella Útmutató

15 Szeptember 2024
Carel

Carel Karta KNX Útmutató

26 Augusztus 2024
Carel

Carel PlantWatch Útmutató

23 Augusztus 2024
Carel

Carel MasterCase Útmutató

18 Augusztus 2024
Carel

Carel Energy2 Útmutató

11 Augusztus 2024
Carel

Carel µC3 Útmutató

11 Augusztus 2024
Carel

Carel powersplit Útmutató

10 Augusztus 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
Soundstream

Soundstream VRN-64HBL Útmutató

10 Április 2025
Panasonic

Panasonic Lumix DMW-AC11 Útmutató

10 Április 2025
Planet

Planet PWR-240-48 Útmutató

9 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
Alpine

Alpine DP2-40C-BC Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025