Használati útmutató CAD Audio U7

CAD Audio mikrofon U7

Olvassa el alább 📖 a magyar nyelvű használati útmutatót CAD Audio U7 (2 oldal) a mikrofon kategóriában. Ezt az útmutatót 13 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
U7 USB Tabletop Recording
Microphone
Before using the U7 in your favorite audio or communications application
you must confi rm that the computer’s operating system recognizes the U7
microphone.
Windows XP recognition instructions
1. Plug the U7 into the USB port on the computer.
(When using a USB hub, check with the hub manufacturer to be sure
the hub supports a device such as a microphone. Plug the microphone
directly into the computer’s powered USB port for optimal performance.)
2. Allow 30 to 60 seconds for the system software to recognize the U7.
(A series of bubbles will appear by the Windows toolbar to notify you
of a new device.)
3. In the Start Menu, select Control Panel.
4. Select “Sounds, Speech, and Audio Devices”.
5. Select “Sounds and Audio Devices”.
6. Select the “Audio” tab. Confi rm that under the “Sound recording”
section the “C-Media USB Audio Device” is selected. (The “Sound
playback” should remain your usual sound output device).
7. Select the “Volume” tab under the Sound recording heading and
select “Advanced Controls” in the Options menu of this window.
8. Click the “Advanced” button to open the “Advanced Controls for
Wave In” window. Depending upon your system, you might have the
option of selecting “1 AGC” or “Mic boost”. Checking this option will
signifi cantly increase the sensitivity of the microphone. Use this for
recording softer sounds. If you experience distortion when recording
louder sounds, try unchecking this option.
(Default playback device)
9. Launch your audio recording software.
10. Position the U7 approximately 4 to 6 inches from the sound source for
best results.
11. Locate the preferences in your audio program and select the “C-Media
USB Audio Device”. Adjust the input level in this program so that the
audio signal is not distorted.
12. Enjoy your CAD U7 USB Tabletop Recording Microphone.
Mac OSX recognition instructions
1. Plug the U7 into the USB port on the computer.
(When using a USB hub, check with the hub manufacturer to be sure
the hub supports a device such as a microphone. Plug the U7 directly
into the computer’s powered USB port for optimal performance.)
2. Allow 30 to 60 seconds for the system software to recognize the U7.
3. Go to the Apple Menu and locate “System Preferences”.
4. Under “Hardware” click on the “Sound” icon.
5. Click on the “Input” button and choose the “C-Media USB Audio Device”.
©2007 CAD Professional Microphones Part No. 64516-22-00 Oct2007
6. or the Click on the “Output” button and choose the internal speakers
output speakers of your choice. (The “Sound playback” should remain
your usual sound output device).
7. Position the U7 4 to 6 inches away from your source (your mouth or
music instrument).
8. Test the U7 by speaking or playing into the microphone.
9. You will see activity in the “Input Level” meter.
10. As you are speaking or playing adjust the “Input Volume” slider. Take
care not to allow the signal to go beyond the meter, if the meter is
fully illuminated the sound can become distorted. The meter should be
illuminated 3/4ths of the way to obtain the best sound quality.
11. Close the System Preferences window to complete the settings.
12. Launch your audio recording software.
13. Position the U7 approximately 4 to 6 inches from the sound source for
best results.
14. Locate the Preferences in your audio program and select the “C-Media
USB Audio Device”. Adjust the input level in this program so that the
audio signal is strong but not distorted.
15. Enjoy your CAD U7 USB Tabletop Recording Microphone.
CAD Professional Microphones
6573 Cochran Rd., Bldg. Solon, OH 44139I
800-762-9266 www.cadmics.com
NOTE: This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment gener-
ates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Two-Year Limited Warranty
CAD Professional Microphones hereby warrants that this product will be free of defects in material and workmanship for a
period of two years from the date of purchase. In the unlikely event that a defect occurs CAD will, at its option, either repair
or replace with a new unit of equal or greater value. Retain proof of purchase to validate the purchase date and return it with
any warranty claim.
Return warranty claims carefully packed, insured and prepaid to the Service Department at the address listed below.
This warranty excludes exterior fi nish or appearance, damage from abuse, misuse of the product, use contrary to CAD’s
instructions or unauthorized repair. All implied warranties, merchantability, or fi tness for a particular purpose is hereby
disclaimed and CAD hereby disclaims liability for incidental, special or consequential damages resulting from the use or
unavailability of this product.
This warranty gives you specifi c legal rights and you may have other rights that vary from state to state. Some states do not
allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts,
so the above exclusions and limitations may not apply to you.
Note: No other warranty, written or oral is authorized by CAD Professional Microphones.
Shipping Instructions
Please call our customer service department at 440-349-4900 for a pre-approved return authorization number. Carefully
repack the unit and return it to: CAD Professional Microphones, 6573 Cochran Road, Building , Solon, Ohio 44139. I
RETURNS WITHOUT A PRE-APPROVED RETURN AUTHORIZATION NUMBER WILL BE REFUSED.
If outside the United States, contact your local dealer or distributor for warranty details.

Termékspecifikációk

Márka: CAD Audio
Kategória: mikrofon
Modell: U7

Szüksége van segítségre?

Ha segítségre van szüksége CAD Audio U7, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók mikrofon CAD Audio

CAD Audio

CAD Audio WX1610 Útmutató

1 Szeptember 2024
CAD Audio

CAD Audio TX1000BP Útmutató

1 Szeptember 2024
CAD Audio

CAD Audio WX1000BP Útmutató

1 Szeptember 2024
CAD Audio

CAD Audio D29 Útmutató

23 Augusztus 2024
CAD Audio

CAD Audio U7 Útmutató

23 Augusztus 2024
CAD Audio

CAD Audio U1 Útmutató

23 Augusztus 2024

Útmutatók mikrofon

Legújabb útmutatók mikrofon

Røde

Røde NT1 Signature Series Útmutató

10 Április 2025
Genesis

Genesis Radium 400 G2 Útmutató

9 Április 2025
Ambient

Ambient TinyMike ATM216 Útmutató

9 Április 2025
Ambient

Ambient Sound Fish ASF-1 MKII Útmutató

9 Április 2025
Ambient

Ambient ASF-G Útmutató

9 Április 2025
Ambient

Ambient Soundfish 2 MkII Útmutató

9 Április 2025
Ambient

Ambient UMP III Útmutató

9 Április 2025
Comica

Comica VP3 Útmutató

2 Április 2025
Atlas Sound

Atlas Sound MWHHM Útmutató

2 Április 2025
Synco

Synco G2A1 Útmutató

2 Április 2025