Használati útmutató Boss NX524

Boss Autó hangszóró NX524

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Boss NX524 (2 oldal) a Autó hangszóró kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
NX524
Installation Instructions
300 Watts / 5.25” (133 mm)
4-Way Full Range Speakers (1 Pair)
- 1 -
Thank you for purchasing a BOSS Audio Systems product. Please read through these
instructions carefully so you will know how to install this product properly.
Package Contents
• 2x Speakers with grills
• 2x Speaker wires with polarity connectors
• 8x Mounting screws and clip nuts
• Installation Instructions/ Cutout Template/
Warranty
Specications
• 4-way full range speakers
Woofer: 5.25” (133 mm),
polypropylene cone, rubber surround
Midrange: 1.25” (30 mm)
Tweeter: 2 x 0.50” (12 mm), dome
• Max output power: 300 W per pair
• Nominal impedance: 4 Ω
• Frequency response: 85 Hz-20 kHz
• System sensitivity: 83 dB (1 watt/1 meter)
• Indoor use. Avoid contact with moisture.
Speaker dimensions
A
BC
F
D
E
G
A. Overall diameter: 5.12” (130 mm)
B. Mounting hole diameter: 4.57” (116 mm)
C. Mounting depth: 2.17” (55 mm)
D. Grill protrusion: 0.98” (25 mm)
E. Overall speaker with grill: 6.10” (155 mm)
F. Tweeter protrusion: 0.28” (7 mm)
G. Outer motor diameter: 3.15” (80 mm)
Customer service: 805-751-4853
Tech support: www.bossaudio.com/support
- 2 -
Installation
You can t the speakers in the factory speaker openings in a vehicle, or create a cutout in a vehicle for speaker
installation.
Consult an expert when in doubt about installation. Professional installation is always recommended.
Prior to installation, disconnect the negative terminal of the vehicle battery.
If you must modify the vehicle for the speaker installation, make sure you do not impair the safety and
structural integrity of the vehicle.
Before you drill or cut any holes, investigate your vehicle’s layout very carefully. Take special care when
you work near the fuel tank, fuel lines, hydraulic lines and electrical wiring.
Option 1: Mounting in the factory speaker location
1. Make sure the factory speaker opening (e.g. in the door or kick panel) ts the speaker in size.
2. Remove the panel which hides the factory speaker locations, and then remove the old speaker.
3. Connect the speaker to the factory speaker wiring with correct polarity. If factory speaker wiring is corroded,
use supplied speaker wires.
4. Fasten the speaker into the factory opening with the supplied screws. Some vehicles may require a speaker
mounting adapter.
Make sure the speaker sits ush across the entire mounting surface.
Make sure the newly installed speaker does not interfere with any operations (e.g. windows rolling all the way
down if in a door, or trunk mechanism if in the rear deck, etc.)
5. Perform a quick test, then reinstall the panel. Be sure to properly break in speakers and not reach max volume
until after two 20 minute cycles at regular volume.
Option 2: Mounting in a new location
1. Remove the interior vehicle panel (e.g. from the door or rear deck) where the speakers are to be mounted.
2. Cut a mounting hole and screw holes on the mounting surface as follows:
• Verify the supplied template matches the speaker and mounting cut-out.
• Cut out the template along the cut line. Use the cut-out template to mark the mounting hole and screw holes
on the mounting surface. Then cut the holes for the speaker to be mounted.
3. Slide the speaker from the top into the hole, and correctly place the supplied speaker grill over the top.
4. Fasten the speaker with four supplied screws and clip nuts.
Make sure the speaker sits ush across the entire mounting surface.
Make sure the newly installed speaker does not interfere with any operations (e.g. windows rolling all the way
down if in a door, or trunk mechanism if in the rear deck, etc.)
5. Using the supplied speaker wires, connect the speaker to your 12VDC source unit (to audio outputs on the
amplier or speaker wires of the head unit).
6. Perform a quick test, then reinstall the panel. Be sure to properly break in speakers and not reach max volume
until after two 20 minute cycles at regular volume.
Wiring
• Make sure the speakers are wired correctly at 4 ohms. Observe speaker polarity when making connections.
• Avoid routing wires near any sharp or moving parts. Run wires away from other wires that may cause unwanted
noise. Insulate bare wires properly.
• Connect the supplied speaker wires to the speakers as follows:
Connect the plug ends of the speaker wires to the speaker terminals, the red wire to the positive terminal and
the black wire to the negative terminal. Make sure the wires are rmly attached to the terminals.
0722

Termékspecifikációk

Márka: Boss
Kategória: Autó hangszóró
Modell: NX524

Szüksége van segítségre?

Ha segítségre van szüksége Boss NX524, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Autó hangszóró Boss

Boss

Boss NX654 Útmutató

2 Szeptember 2024
Boss

Boss B65LED Útmutató

28 Augusztus 2024
Boss

Boss P55.4C Útmutató

17 Augusztus 2024
Boss

Boss Chaos Exxstreme CX124DVC Útmutató

14 Augusztus 2024
Boss

Boss BE423 Útmutató

12 Augusztus 2024
Boss

Boss PC65.2C Útmutató

12 Augusztus 2024
Boss

Boss BE524 Útmutató

12 Augusztus 2024
Boss

Boss ASK904B.64 Útmutató

12 Augusztus 2024
Boss

Boss S12A Útmutató

9 Augusztus 2024
Boss

Boss NX524 Útmutató

8 Augusztus 2024

Útmutatók Autó hangszóró

Legújabb útmutatók Autó hangszóró

Audiotec Fischer

Audiotec Fischer Match Up C42BMW-FRT Útmutató

9 Április 2025
Pioneer

Pioneer TS-271M Útmutató

6 Április 2025
Pioneer

Pioneer TS-351M Útmutató

6 Április 2025
Focal

Focal IC VW 165 Útmutató

29 Március 2025
Focal

Focal IC REN 130 Útmutató

29 Március 2025
Focal

Focal IS REN 130 Útmutató

29 Március 2025
Focal

Focal IS RNS 165 Útmutató

28 Március 2025
Focal

Focal IS PSA 165 Útmutató

27 Március 2025
JL Audio

JL Audio C2-650 Útmutató

12 Január 2025
JBL

JBL P963 Útmutató

1 Január 2025