Használati útmutató Blomberg OEN 84S80 B

Blomberg sütő OEN 84S80 B

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Blomberg OEN 84S80 B (2 oldal) a sütő kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

Contents of Carry bag

Tent body

Tent y

Pole bag: 2 solid-color main poles, 1 y pole

with black center section

Stake bag: stakes, guyout cords, pole repair sleeve,

fabric repair swatches.

Setting up the Tent Body

1. Spread the tent body out, oor side down. Locate the tan webbing

stake out loop, as this marks the front of the tent.

2. Assemble the two main poles and lay the poles on top of the tent body

so they form an “X”.

3. Starting at the corner with the tan webbing stake out loop, insert the

tip of the pole into the grommet (metal ring). Moving to opposite end of

pole, pressure the pole to bend it upwards & insert the pole tip into the

grommet. Repeat process with second pole.

4. Secure the poles where they cross by reaching down to the tent body

and raising the center of the tent, wrap the black webbing loop around

“X” formed by the poles and pass the black “dog-bone” toggle through

the webbing loop.

5. Walk around the tent and connect all of the black plastic clips to their

respective poles.

6. Secure the tent to the ground using the stakes provided. Start at the

tan webbing stake out loop, next proceed to opposite corner, and while

rmly pulling on the black webbing stake out loop hammer in the stake.

Repeat process with the other two corners. At this time, leave the

Forward Operating Base’s black webbing stake out loops unanchored.

7. The tent body will now be erect, properly tensioned, and secured

to the ground.

Attaching the Fly Sheet

1. Assemble the y pole (pole with black center section)

2. Spread the ysheet on the ground with the outside upwards and

the tan webbing strap with buckle on your right.

3. Locate the dark-colored fabric pole sleeve and thread the pole

through the sleeve, through the tan webbing loop located at the top

center of the y, and then through the second dark-colored fabric

pole sleeve. Center the black section of the pole under the ysheet’s

tan webbing loop.

4. Matching the y’s tan webbing strap to the tent body’s tan

webbing stake out loop, drape the y over the tent body, centering

the y’s tan webbing loop above the “X” formed by the tent body’s

main poles.

5. Align and center the y on the tent body so the 4 buckles match,

and the y’s seams follow the tent body’s poles.

6. Grasping the tip of the y pole, bend the pole down towards the

ground and insert one tip of the y pole into the grommet of the

Forward Operating Base’s black webbing stake out loop. Repeat

process with other end of y pole.

7. Secure with stakes the two Forward Operating Base’s black

webbing stake out loops.

8. Locate the black webbing guyout loops on the outside of the

ysheet, reaching under the guyout loops, wrap the hook/loop

closure around the underlying pole to secure the y to the pole

structure.

9. Now clip the buckles at each of the six locations, pulling the

webbing through the buckles to tension the y.

10. Vectored Side Pullouts: This tent features y-to-tent body

pullouts. At the mid-point on each end of the tent, reach under the

y’s edge, slide the black “dog bone” toggle through the “O-Ring”

located on the tent body. Attach a provided guyout cord to the small

webbing loop. Secure guyout cord with a stake. Repeat process on

other side of tent. The Vectored Side Pullouts enhance ventilation,

increase the tent’s interior living space, and strengthen the overall

tent during inclement weather.

Snivel Locks:

Both front and rear vestibules’ door panels lock at bottom with

a side-release buckle to eliminate wind-driven opening

Gear Hammock:

A removable 3 pocket hammock hangs along the

side of tent keeping small items organized & o the oor.

Hammock attaches with hooks to pre-installed webbing loops

located in each corner of the tent.

Eureka! Set-Up Instructions

Down Range Solo (#2629340) Tent

11. Guyouts: Attach the provided guyout cords to the four black

webbing guyout loops. Get in the habit of always using the guyouts,

even in good weather.

REV 090613

Good:

4 stakes /4 lines

Best:

4 stakes /8 lines

SEAM SEALING:

We recommend use of a sealer such as Kenyon Seam Sealer 3 or McNett

Outdoor SeamGrip

• Work in a fully ventilated area.

• Set the tent up or lay the tent out ﬂat. Taut seams allow for even

application and penetration of the sealer.

• Decide which seams need to be sealed. For example, seams that will be

exposed to rain, runo, or ground level water are a must for sealing, while

seams on uncoated nylon or mesh panels don’t need treatment. There is

no need to seal the seams in the roof or the factory taped seams. We

recommend sealing both ﬂoor and ﬂy seams and reinforcements.

• Apply sealant to the inside and outside of all exposed seams. Several thin

layers will work better than one thick layer. Read and follow

manufacture's instructions.

STAKING:

All tents need to be staked down to keep them from blowing away.

Securing the tent by placing heavy objects inside is just not adequate.

• Once the tent body is erected, stake it out before the ﬂy is put on. This

enables you to square the tent up to ensure that the ﬂy goes on properly

and that the seams align with the frame. Pull the base of the tent taut

between each web stake out loop or ring & pin. Make sure that all corners

are square. It is important that you don’t stake the tent out too tightly.

You will know it’s too tight, if the door zippers can not be easily operated.

Drive stakes through the web loops, or with ring & pin, drive the stake

just outside the ring so that the “J” hook catches it. Tie a piece of cord or

web into a loop through the ring to be used as a large stake loop if

needed.

• With the tent properly staked, drape the ﬂy over the frame, attach its tent

connection points and stake down any pull outs.

• Do not attempt to remove the stakes by pulling on the tent becket loop,

as this could cause the fabric to tear. The best way is to pry on the stake

itself.

STAKING IN SPECIAL CONDITIONS:

• Sand. Use long, broad stakes with plenty of surface area in loose soil.

• Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel stakes

separately. Their sharp edges can cut fabric and leave rust stains, which

might damage your tent.

• Snow. Use “dead man” anchors. Tie tent to buried objects (branches, tent

bags, or stu sacks ﬁlled with snow; or tie tents to snow shoes, skis, or ski

poles, which are stuck in the snow.

GUY LINES:

Do not depend upon staking alone to keep your tent secure during high

winds. Most tent models have built-in loops or rings at optimal guy out

locations. It’s important to put in the extra time guying out your tent.

Correctly done, it can save your tent during exceptional weather.

• Make sure that the top ﬂy is securely attached to the tent frame. Ties, hook

and loop, or dog-bones and elastic loops are sewn to the underside of the

ﬂy for this purpose.

• Attach parachute cord to the loops/rings and stake them in the ground

three or four feet from the edge of the tent. If staked too close to the tent,

wind can cause an upward pull that could dislodge the stakes.

• If your tent does not have loops or rings for guy outs, attach guy lines 1/3

to 1/2 of the way up the framework on the main sidewalls. This enables

the guy line to support the lower section of the pole, while the upper

pole can ﬂex and deﬂect wind gusts. It is best to run two cords at an

angle from the side of the guy out. This prevents all movement, except

toward the anchor. The guy lines will work together through opposition.

See illustrations.

CONDENSATION & VENTING:

Through perspiration and breathing, an adult gives off about a pint of

water overnight. If it cannot escape, the water vapor condenses to liquid.

Most often, water found in the tent is a result of this condensation rather

than from the tent leaking. Condensation often forms where the sleeping

bag touches the side of the tent, under the sleeping pad, or on coated

surfaces such as the door ﬂaps. A tent’s double wall construction allows

the vapor to escape through the roof to the outside, keeping the inside of

the tent dry.

Leave the windows partially open at night to provide cross ventilation and

further reduce condensation. Cross ventilation becomes more important

in very humid or extremely cold conditions when the permeable roof is

less effective. The features that enhance ventilation are windows,

short-sheeted ﬂys (bottom venting), roof vents, and High/Low venting

doors. These are speciﬁc to each tent model.

Given the importance of proper ventilation, We use High/Low venting in

most of our tents. This allows cooler air in through the low vents and

warmer, moist air up and out through the high vents. High/Low venting is

accomplished within the inner tent via roof vents, doors and windows. It

is important to vent the vestibule. Unvented, it can inhibit airﬂow into the

tent. Our tent vestibules proﬁt from the ability to “short sheet” by means

of zippers & toggles and staked vestibule pull outs create a bellowing

effect.

Most of our tents are equipped with a High/Low venting door. This design

allows increased airﬂow into the tent from the bottom. Open the low

vent/window to admit cool air, allowing the warmer air out through the

high roof vents. When rain and wind prevent the low vent from being

opened, the high door vent can still be used. Fly overhangs or vestibules

protect it.

ULTRAVIOLET LIGHT:

Ultraviolet light damage to tent fabric is caused by excessive exposure to

sunlight. While our fabrics are UV resistant, any synthetic fabric is

susceptible to UV degradation. UV damage will cause nylon and polyester

to become brittle and tear easily. We recommend that you use the rain ﬂy

even on clear days. It acts as a sunscreen to the tent. A rain ﬂy is both

easier and less expensive to replace if damaged. UV damage can be

minimized by erecting tents on shaded sites with low exposure to direct

sunlight.

GENERAL POLE CARE:

• Never let tent poles snap together as this can damage the pole end.

• Do not drop tent or pole bags on their ends and do not bounce a tent bag

on its end to get the tent out. These actions may cut the shock cord and

damage the pole ends.

• The aluminum frame may bend slightly and take a “set” through usage;

this normally does not affect the performance of the frame.

GENERAL TENT CARE:

• Sweep the tent ﬂoor daily to prevent damage from stones.

• Try not to wear shoes inside your tent.

• Use a ground cloth whenever possible.

• Do not keep food inside a tent. Hungry critters will chew through

tent fabric in search of food.

STORAGE:

• Make sure the tent is completely dry, then store loosely rolled, in a

dry, cool place. To prevent dust from collecting on the tent, cover it

with a cloth. This allows the nylon/polyester fabric to breathe.

• Ideally, the tent poles should be stored in their fully assembled state.

This reduces the tension on the shock cord, prolonging its life.

• The tent bag should be used only as a carry sack and not for storage.

COLOR TRANSFER:

• Do to the nature of tent fabrics, color can transfer from darker to

lighter fabrics when the two fabrics are in contact over time when

wet, damp or exposed to the combination of moisture and high

heat. This does not eect the tent's performance. To prevent /

minimize color transfer, always make sure your tent is completely dry

prior to packing and storage.

CLEANING:

• Clean the tent by setting it up and wiping it down with a mild soap

(liquid hand soap) and lukewarm water solution. Rinse thoroughly

and dry completely. Never use detergent, washing machines or

dryers because they can damage the tent’s protective coating and

seams. After cleaning, be sure the tent is completely dry, especially

the heavier, double-stitched areas such as the seams, before storing

or mold / mildew are likely to grow.

• Clean the tent poles with a cloth and lubricate them with silicone

spray. This is especially necessary after ocean side camping to

remove salt spray so the poles don’t corrode or stay gritty.

• Clean the zippers with a quick dip in water and then dry them o.

This is especially important if you’ve been camping in a location with

sand/dirt. If you don’t clean the zippers, the sliders will wear out and

eventually the teeth will become inoperable.

ALTERATIONS OR MODIFICATIONS:

DO NOT misuse, modify or alter this product in any way from its

condition at the time of sale. Alteration, modication or any use of

this product contrary to the accompanying written instructions shall

void the warranty. Moreover, any misuse, alteration or modication

of the product shall absolve Johnson Outdoors Gear LLC of any

liability for property damages or injuries sustained as a result of such

misuse, modication or alteration.

LIMITED WARRANTY:

What Is Covered: Johnson Outdoors Gear LLC

warrants to the original

purchaser that its products are free from defects in material and

workmanship, for the life of the product, except as qualiﬁed below. The

life of the product is determined from the date of purchase until such

time as the product is no longer serviceable due to normal wear and

tear.

What Is Not Covered:

Johnson Outdoors Gear LLC

shall not be responsible

for the natural breakdown of materials that occurs inevitably with

extended use (e.g., Ultra Violet (UV) light damage on tents, exhausted

zippers), or defects caused by accident, abuse, alteration, animal attack,

storm damage, misuse or improper care.

THERE ARE NO OTHER EXPRESS WARRANTIES BEYOND THE TERMS

OF THIS LIMITED WARRANTY.

IN NO EVENT SHALL JOHNSON OUTDOORS GEAR LLC

BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES.

Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

What Johnson Outdoors Gear LLC Will Do: If after

inspection we ﬁnd that a product failed due to a

manufacturing or material defect, we will repair or

replace the product, at our option, without charge.

How to Obtain Warranty Service: Return the product,

freight prepaid, to the Dealer from whom it was

purchased; or, contact our Customer Satisfaction

Department for return authorization: toll free

1-800-572-8822. Collect shipments or shipments without

return authorization cannot be accepted. The product

registration card packaged with our product need not

be returned for the warranty to be eective and for you

to receive warranty service.

Repairs: If your

Johnson Outdoors Gear LLC

product

needs service or repair due to normal wear and tear,

animal attack, accident or some other reason that is not

covered under the warranty we will provide the

necessary service for a reasonable charge, plus shipping

and handling. We require that products accepted for any

repair be properly cleaned according to our

recommended care instructions. Please send your

product or component that requires

repair (e.g., tent ﬂy),

postage prepaid, along with a description of what needs

attention. For service and repairs, please contact our

Customer Satisfaction Department: toll free

1-800-572-8822

How State Law Relates To This Warranty: This warranty gives

you speciﬁc legal rights, and you may have other rights

that vary from state to state.

Our brands are part of the Johnson Outdoors

family of products. Visit all the brands at

johnsonoutdoors.com

We support the "Leave No Trace" Seven

Principles:

1. PLAN AHEAD AND PREPARE

2. TRAVEL & CAMP ON DURABLE SURFACES

3. DISPOSE OF WASTE PROPERLY

4. LEAVE WHAT YOU FIND

5. MINIMIZE CAMPFIRE IMPACTS

6. RESPECT WILDLIFE

7 . BE COURTEOUS OF OTHER VISITORS

JOHNSON OUTDOORS GEAR INC

WARNING:

KEEP ALL FLAME AND HEAT SOURCES

AWAY FOM THIS TENT!

This tent meets the ammability requirements of CPAI-84. The Fabric may burn

if continuous cntact with any ame source. Do NOT operate any device which

burns fuel inside your tent. This could lead to serious injury or death.

REV 090613

Termékspecifikációk

Márka:	Blomberg
Kategória:	sütő
Modell:	OEN 84S80 B

Szüksége van segítségre?

Ha segítségre van szüksége Blomberg OEN 84S80 B, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók sütő Blomberg

Blomberg BGR 24100 SS Útmutató

30 Szeptember 2024

Blomberg MKN 14321 Útmutató

22 Szeptember 2024

Blomberg ODN 9462 Útmutató

22 Szeptember 2024

Blomberg MKN 24001 Útmutató

17 Szeptember 2024

Blomberg ODN9462 Útmutató

10 Szeptember 2024

Blomberg HMN 9130 E Útmutató

8 Szeptember 2024

Blomberg OEN 9302 Útmutató

8 Szeptember 2024

Blomberg OEN 84S80 B Útmutató

8 Szeptember 2024

Blomberg ROKW8370B Útmutató

1 Szeptember 2024

Blomberg MIN74387NP Útmutató

1 Szeptember 2024

Útmutatók sütő

Legújabb útmutatók sütő

Electrolux ekm 6700 w Útmutató

8 Április 2025

Constructa CB10453 Útmutató

8 Április 2025

Instant Omni Plus Toaster Útmutató

8 Április 2025

Breville the Quick Cook Dual Zone LIC700 Útmutató

8 Április 2025

Bosch PGQ7B5K90 Útmutató

8 Április 2025

Bosch PNP6B6K40 Útmutató

8 Április 2025

Gaggenau VG425115 Útmutató

8 Április 2025

Arendo 307502 Útmutató

8 Április 2025

V-Zug Combair XSL 60 Útmutató

8 Április 2025

Zanussi BMW 15 Útmutató

7 Április 2025