Használati útmutató Bertazzoni CB36500X

Bertazzoni sütő CB36500X

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Bertazzoni CB36500X (16 oldal) a sütő kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/16
(GB) INSTRUCTIONS FOR THE INSTALLATION, MAINTENANCE
pag. 2 AND USE OF FIXED HOBS WITH GAS OR MIXED SUPPLY
DROP IN (TYPE P92/P92V)
(FR) INSTRUCTIONS POUR L'INSTALLATION, L'ENTRETIEN ET
page. 7 L'UTILISATION DES TABLES DE CUISSON ENCASTRABLES
GAZ ET MIXTES
DROP IN (MODELE P92/P92V)
2
(GB) READ THE INSTRUCTION BOOKLET BEFORE INSTALLING AND USING THE APPLIANCE.
These instructions are valid only for those countries which are indicated by their identification symbol on the front cover of the
instruction booklet and on the label on the appliance.
The manufacturer cannot be held responsible for any damage to things or persons caused by an incorrect installation or by
incorrect use of the appliance.
The manufacturer cannot be held responsible for any inaccuracies due to errors in printing or writing contained in this booklet. The
appearance of the figures shown is also only approximate.
The manufacturer reserves the right to make changes to his products when it is considered necessary and useful without effecting the
essential features regarding safety and function.
INDEX:
TECHNICAL MANUAL FOR THE INSTALLER ........................................................................................................ pag. 2
Inserting the hob ......................................................................................................................................................... pag. 2
Fixing the hob – Advice about installation ................................................................................................................... pag. 3
Ventilation and airing of the premises – Connection to the gas supply ....................................................................... pag. 3
Adaptation to different types of gas ............................................................................................................................ pag. 3
Regulation of the burners ............................................................................................................................................ pag. 4
Connection to the electricity supply ............................................................................................................................. pag. 4
MAINTENANCE OF THE APPLIA ........................................................................ pag. 4 NCE – Replacing parts ................
USE AND MAINTENANCE MANUAL ........................................................................................................................ pag. 5
Description of types of hobs ........................................................................................................................................ pag. 5
Use of the burners ....................................................................................................................................................... pag. 5
Cleaning of the appliance ........................................................................................................................................... pag. 6
Figures ........................................................................................................................................................................ pag. 11
Electrical Diagran ........................................................................................................................................................ pag. 14-15
THIS APPLIANCE HAS BEEN DESIGNED FOR NON PROFESSIONAL USE IN HOUSEHOLDS.
TECHNICAL MANUAL FOR THE INSTALLER
INFORMATION FOR THE INSTALLER
The installation, all regulations, changes and maintenance referred to in this part must only be carried out by qualified staff.
A wrong installation can cause damage to persons, animals or things which the manufacturer cannot be held responsible for.
The safety and automatic regulation devices on the appliances can only ever be changed by the manufacturer or by the
supplier which has been authorised to do so.
INSERTING THE HOB
When you have removed the various adjustable parts from their internal and external packaging, check that the hob is intact. If you are
in doubt do not use the appliance and contact the qualified staff.
The parts which make up the packaging ( polystyrene, bags, boxes, nails etc. ), are dangerous objects and must be kept out of
children’s reach.
Taking into consideration the specific dimensions of the appliance (see table N°1), make an opening in the work surface (see figure 1)
using the measurements indicated in table N°.1
The appliance must be classified in class 3 and thus it is subject to all the regulations indicated by the norms regarding these
appliances.
Table N°.1
Hobs models B3W0…
B3Y...
Hobs models B3W0…
B3Y...
Min. Clearances mm Min. Clearances mm
L1 520 L10 905
L2 40 L11 915
L3 40 W 925
L4 457 D 540
L5 610 B1 (*) 40
L6 330 B2 (*) 152
L7 925 B3 (*) 30
L8 20 B4 (*) 152
L9 162
(*) Note:
-B1 is the min. clearance between the front edge of the appliance and the front edge of the cabinet.
-B2 and B4 are the min. clearanc dge of the appliance and the side wall (if e between the left/right side e
present).
-B3 is the min. clearance between the back edge of the appliance and the back wall.
3
ATTACHING THE HOTPLATE
To prevent liquids from leaking accidentally into the underlying storage space, the appliance is equipped with a special gasket. To apply
this gasket, carefully follow the instructions in Fig. 3. Lay out the protective sealing strips along the edges of the opening in the bench
top and carefully overlap the strip end. (See Fig. 3). insert the hotplate into the bench top opening. With a screwdriver assemble the
brackets A to the hotplate bottom by means of the screws B. (See Fig. 4). Slide the hooks into position and secure them with the screws.
Trim the part of the sealing strips which extend beyond the hotplate base
IMPORTANT INFORMATION CONCERNING THE INSTALLATION OF THE APPLIANCE
We inform the installer that this hob is of the Y type and thus it can be installed by itself, in an isolated position or inserted
between two kitchen units or between one kitchen unit and a wall. Furthermore the back wall and surrounding surfaces must
resist a temperature of 65 K.
To prevent the plastic layer which covers the kitchen unit from ungluing, the glue used to join the two surfaces together must
resist temperatures of up to 150 °C
The installation of the appliance must be carried out according to the norms in force of the country concerned and the
appliance must be installed in a well ventilated place.
This appliance is not equipped with devices to remove the products of combustion. The appliance must therefore be
connected following the norms for installation mentioned above. Special attention must be paid to the information below
regarding aeration and ventilation of the premises.
VENTILATION OF THE PREMISES
To guarantee that the appliance works correctly it is necessary that the place where the appliance is installed is continuously ventilated.
The volume of the premises must not be less than 25 m³ and the quantity of air needed must be based on the regular combustion of
gas and on the ventilation of the premises. The natural flow of air will take place through permanent openings made in the wall of the
premises to be ventilated: these openings will be connected to the outside and must have a minimum section of 100 cm² ( see Fig. 6 ).
These openings must be made in such a way that they cannot be obstructed.
POSITION AND VENTILATION
The cooking appliances that use gas must always remove the products of combustion via a hood linked to chimneys, chimney flues or
via a direct connection to the outside ( see Fig. 6A ). If it is not possible to fit a hood it is possible to use a fan, fitted on the window or
facing directly outside, which operates when the appliance is in use. ( see Fig. 6B ). In this way the norms in force of the country
concerned regarding the ventilation of premises are strictly followed.
CONNECTING THE APPLIANCE TO THE GAS SUPPLY
Before connecting the appliance to the gas supply you first need to remove the plastic protective plug for the gas supply which
is inserted under pressure in the gas inlet connection. To remove the plug simply unscrew it.
Then make sure that the details shown on the label on the lower part of the case are compatible with those of the gas supply.
A label on the last page of this manual and on the lower part of the case indicates the conditions for regulating the appliance:
type of gas and pressure used.
IMPORTANT: This appliance must be installed in accordance with the norms in force of the country concerned and it must only
be used in a well-ventilated place.
ATTENTION: Remember that the gas inlet connection for the appliance is threaded 1/2 gas cylindrical male in accordance with
the norms UNI-ISO 228-1. (Fig. 5)
ADAPTING TO DIFFERENT TYPES OF GAS
Before carrying out any maintenance work, disconnect the appliance from the gas and electric supply.
- CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS:
To change the nozzles of the burners use the following procedure:
Lift up the burners and unscrew the nozzles ( Fig. 9) using an adjustable spanner of 7 mm and change the nozzles with those designed
for the new gas supply according to the information given in TABLE N° 2 shown below.
ATTENTION: After carrying out the changes described above, the technician must put the label corresponding to the new gas
supply on the appliance to take the place of the old label. This label is found in the bag containing spare nozzles.
TABLE N°2: Adapting to different types of gas APPLIANCE CATEGORY: II2H3+
Burner Type of Gas Pressure Nozzle Nominal Charge Reduced Charge Diameter
diameter by-pass 1/100mm
mbar 1/100mm g/h l/h Kw kcal/h kw kcal/h safety
Natural G20 20 77 - 95 1 860 0,3 258 27
Auxiliary Butane G30 28-30 50 73 - 1 860 0,3 258 27
Propane G31 37 50 71 - 1 860 0,3 258 27
Semi- Natural G20 20 101 - 167 1,75 1505 0,44 378 31
Rapid Butane G30 28 66 127 - 1,75 1505 0,44 378 31
Propane G31 37 66 125 - 1,75 1505 0,44 378 31
Natural G20 20 129 - 286 3 2580 0,75 645 42
Rapid Butane G30 28 87 218 - 3 2580 0,75 645 42
Propane G31 37 87 214 - 3 2580 0,75 645 42
Dual
Natural G20 20 In 70 - 476 5 4300 0,48 413 In 34
Out 2x110 Out 65
Butane G30 28 In 46 334 - 4,6 3956 0,48 413 In 34
Out 2x69 Out 65
Propane G31 37 In 46 338 - 4,6 3956 0,48 413 In 34
Out 2x69 Out 65

Termékspecifikációk

Márka: Bertazzoni
Kategória: sütő
Modell: CB36500X

Szüksége van segítségre?

Ha segítségre van szüksége Bertazzoni CB36500X, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók sütő Bertazzoni

Bertazzoni

Bertazzoni MAS100 6 MFE DXE Útmutató

3 Április 2025
Bertazzoni

Bertazzoni HER120 6G MFE DNET Útmutató

31 Március 2025
Bertazzoni

Bertazzoni HER90 6 MFE DNET Útmutató

30 Március 2025
Bertazzoni

Bertazzoni Professional PROF365INSGIT Útmutató

12 Január 2025
Bertazzoni

Bertazzoni HER126G2EAVT Útmutató

4 Január 2025
Bertazzoni

Bertazzoni PRO96L1EGIT Útmutató

4 Január 2025
Bertazzoni

Bertazzoni PRO96L1EART Útmutató

4 Január 2025
Bertazzoni

Bertazzoni PRO96L1EBIT Útmutató

4 Január 2025
Bertazzoni

Bertazzoni PRO95I1ENET Útmutató

4 Január 2025
Bertazzoni

Bertazzoni PRO95I1EROT Útmutató

4 Január 2025

Útmutatók sütő

Legújabb útmutatók sütő

Scarlett

Scarlett SC-EO93O18 Útmutató

3 Április 2025
AEG

AEG Competence 573 V W Útmutató

2 Április 2025
Samsung

Samsung BQ1AD4T243 Útmutató

2 Április 2025
Zanussi

Zanussi zhn 723 zht 74 kp Útmutató

2 Április 2025
Atag

Atag ox60 a Útmutató

2 Április 2025
Electrolux

Electrolux EON3010 Útmutató

2 Április 2025
De Dietrich

De Dietrich DOP790 Útmutató

2 Április 2025
Krefft

Krefft RGC 051M Útmutató

2 Április 2025
Stoves

Stoves SE60MFPTi Útmutató

2 Április 2025
Wolf

Wolf CI30460C/B Útmutató

2 Április 2025