Használati útmutató Benro Video Monopod A48FDS4

Benro Háromlábú Video Monopod A48FDS4

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Benro Video Monopod A48FDS4 (2 oldal) a Háromlábú kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
Classic Series Monopods
Operating Instructions
Thank you for making Benro your choice for professional photographic
equipment. Your Benro gear is manufactured to provide years of
dependable service. In order to obtain optimum satisfaction and
performance, we suggest that you carefully read these instructions.
Specifications and design are subject
to change without notice.
75 Virginia Road
North White Plains, NY 10603
T 914.347.3300
F 914.347.3309
info@BenroUSA.com
BenroUSA.com
SETUP
Head Mounting (FIGURES 1 & 2)
If your Monopod did not come with a Head,
select one of the fine Benro Ballheads or
Tilthead that match your size Monopod
and install by screwing the Head clockwise
onto the 3/8" Mounting Thread of the Top
Plate. Once it is hand tight, secure by fully
tightening the Head Locking Screw(s) (on
select models) from below.
Most Heads have a 3/8" Base Mount so your
Benro Monopod is shipped with the 3/8
Mounting Thread exposed, but if the Head
you choose uses a 1/4–20 you can attach it
by simply reversing the Mounting Screw.
To do this turn the Locking Nut counter-
clockwise (using the supplied Wrench)
until it becomes loose, and unscrew the
Mounting Screw until it can be completely
removed. Reverse the Screw, so that the
threads are in position and screw it back
into place, secure with the Locking Nut
using the wrench.
NOTE: Allow enough of the screw threads
to be available for maximum security when
the Head is mounted onto the Monopod.
It’s recommended that at least 5 to 6
threads be exposed before locking the
Mounting Screw in place.
OPERATION
Before using your Monopod, adjust each
Leg Section to the desired height.
Make sure that the Monopod is firmly resting
on a stable surface and mount your camera
securely on the Monopod Head. Always
engage any safety locks on the Monopod
Head to prevent any accidental dismounting.
FOR BEST RESULTS: Do not raise the
Monopod higher than necessary and extend
the largest diameter Leg Sections first.
NOTE: Never carry your Monopod with
camera gear attached.
Leg Section Adjustment (FIGURES 3 & 4)
Each Leg Section can be adjusted to the
desired length by opening the Flip Lock
Lever so the Leg is free to slide in or out.
Once the desired length is achieved, snap
the Flip Lock Lever closed so that the leg
section is securely locked. Repeat this step
for each Leg Section until the Monopod is
set to the desired height.
NOTE: To prevent any accidental damage
to your gear, always remove any mounted
equipment (camera, etc.) from the Monopod
before adjusting the Leg Sections.
User Adjustments (FIGURE 5)
Flip Lock Lever tension is adjusted using the
3mm Allen Key plus the special Six-sided
Socket Wrench built into the plastic clip
which comes attached to the monopod leg.
USER NOTICE
• Do not exceed the maximum specified
load capacity (see specifications at
www.BenroUSA.com).
• Always ensure that Leg and Head Locks
are tightly engaged before mounting any
gear on your Monopod.
• Always clean and dry any Monopod after
it has been exposed to wet, dusty, sandy
or salty conditions. Your Monopod is
not recommended for use in salt water.
If required, clean Monopod using a mild
soap solution applied with a soft cloth,
rinse with fresh water and dry with soft
towel. Remove any dust, dirt or sand
from all Leg Locks, Leg Sections and all
moving parts.
• Do not leave any Monopod in the sun
for prolonged periods and avoid high
temperature exposure.
• Avoid leaving any Monopod or Tripod
unattended in areas where people could
trip over the equipment and get hurt.
• Remove camera, lens, and all gear from
the Monopod when transporting.
• For your safety, don’t let your Benro
gear come in contact with any electrical
power source.
Top Plate
Flip Lock Lever
Closed Cell Foam Grip
Wrist Strap
Rotating Pod Foot
Locking Nut
1/4-20 + 3/8
Mounting Screw
Wrench
21
Unlock Lock
3 4
3mm Allen Key
6-sided Socket
Wrench Clip
5
Operating Instructions & User Notice

Termékspecifikációk

Márka: Benro
Kategória: Háromlábú
Modell: Video Monopod A48FDS4

Szüksége van segítségre?

Ha segítségre van szüksége Benro Video Monopod A48FDS4, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Háromlábú Benro

Benro

Benro S4 Pro Útmutató

8 December 2024
Benro

Benro S8Pro Útmutató

8 December 2024
Benro

Benro S2Pro Útmutató

8 December 2024
Benro

Benro ITrip FIT19AIH0 Útmutató

8 Október 2024
Benro

Benro BV4PRO Útmutató

3 Október 2024
Benro

Benro KH25N Útmutató

20 Szeptember 2024
Benro

Benro Video Monopod A48FDS4 Útmutató

8 Szeptember 2024
Benro

Benro HD3A Útmutató

4 Szeptember 2024
Benro

Benro C2573FS4 Útmutató

1 Szeptember 2024
Benro

Benro C1573FS2 Útmutató

25 Július 2024

Útmutatók Háromlábú

Legújabb útmutatók Háromlábú

Cartoni

Cartoni Master M111 Útmutató

11 December 2024
Cartoni

Cartoni Maxima Útmutató

11 December 2024
Cartoni

Cartoni Focus 12 Útmutató

11 December 2024
Cartoni

Cartoni Focus 8 Útmutató

11 December 2024
Cartoni

Cartoni Focus 18 Útmutató

11 December 2024
HPRC

HPRC 2700W-01 Útmutató

11 December 2024
Really Right Stuff

Really Right Stuff BH-40 Útmutató

11 December 2024
Really Right Stuff

Really Right Stuff BH-55 Útmutató

11 December 2024
Really Right Stuff

Really Right Stuff BH-25 Útmutató

11 December 2024
Really Right Stuff

Really Right Stuff BH-30 Útmutató

11 December 2024