Használati útmutató Axxess HDCC-02

Axxess nincs kategorizálva HDCC-02

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Axxess HDCC-02 (8 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/8

Installation instructions for part HDCC-02

REV. 5/27/2016 INSTHDCC-02

Axxess Integrate

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• Provides accessory power (12-volt 10-amp)

• Provides NAV outputs (parking brake, reverse, speed sense)

• Pre-wired ASWC-1 harness (ASWC-1 sold separately)

• Retains factory backup camera

• Retains LaneWatch camera

• Retains ability to change factory clock and date

• Retains factory AUX-IN jack

• Can be used in non-amplified, or amplified models

• High level speaker input

• Retains balance and fade

• Micro “B” USB updatable

FEATURES

• Cutting tool • Crimping tool • Tape • Connectors

(example: butt-connectors, bell caps, etc.)

TOOLS REQUIRED

• HDCC-02 interface • HDCC-02 harness

INTERFACE COMPONENTS

APPLICATIONS

HONDA

Civic 2014-2015

CR-V 2015-up

HDCC-02

Connections to be made

From the HDCC-02 harness to the aftermarket radio

(a) Main harness:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• Connect the wire to the accessory wire.Red

• If the vehicle is equipped with a factory amp, connect the wire to Blue/White

the amp turn-on wire.

Note: This wire must be connected to hear sound from the factory amplifier.

• Connect the wire to the left front positive speaker output.White

• Connect the wire to the left front negative speaker output.White/Black

• Connect the wire to the right front positive speaker output.Gray

• Connect the wire to the right front negative speaker output.Gray/Black

• Connect the wire to the left rear positive speaker output.Green

• Connect the wire to the left rear negative speaker output.Green/Black

• Connect the wire to the right rear positive speaker output.Purple

• Connect the wire to the right rear negative speaker output.Purple/Black

(b) 16-pin harness:

• Connect the wire to the illumination wire (if the aftermarket Orange/White

radio has no illumination wire, tape off and disregard this wire).

The following (3) wires are for aftermarket multimedia/navigation radios that

require these wires:

• Connect the wire to the parking brake wire (if applicable).Light Green

• Connect the wire to the speed sense wire (if applicable).Blue/Pink

• Connect the wire to the reverse wire (if applicable).Green/Purple

• Connect the Yellow RCA jack to the backup camera input (if applicable).

Note: This RCA jack is used to retain the backup camera as well as the

LaneWatch camera.

• Connect the RCA jacks to the audio AUX-IN jacks (if applicable).White Red and

• If the vehicle is equipped with a factory amp, connect the White RCA jack to the

subwoofer output jack.

(d) 12-pin pre-wired ASWC-1 harness:

• This harness is to be used in along with the optional ASWC-1 (not included)

to retain steering wheel audio controls. If the ASWC-1 is not being used,

disregard this harness. If it will be used, please refer to the ASWC-1

instructions for radio connections and programming.

Note: Disregard the harness that comes with the ASWC-1.

Installing the HDCC-02

With the key in the off position:

• Connect the 22-pin connector of the HDCC-02 harness, into the

HDDC-02 interface.

• Connect the (2) 24-pin, 12-pin, 8-pin and 20-pin connectors of the HDCC-02

harness into the vehicle.

Connections to be made

HDCC-02

Initializing the HDCC-02

LaneWatch settings:

Note: The LaneWatch button is located on the left side of the steering wheel,

on the stalk.

• Press and hold the LaneWatch button for 15 seconds to toggle right turn signal

triggering on or off. If on, press and hold the button again for 15 seconds to

toggle it off. Likewise if off. The hi-beam indicator will flash 1 time if off; 2 times

if on.

Note: Right turn signal triggering is default on.

CAUTION! The following step should only be performed by an authorized

Honda technician. Once this procedure has been started, you cannot back

out of it.

• Press and hold the LaneWatch button for 50 seconds to begin the LaneWatch

aiming procedure. The hi-beam indicator will flash 3 times. At this point

the display will also show an image of the LaneWatch camera feed, with

instructions on what to do--a Honda authorized technician will know what to do

from here.

Note: While accessing LaneWatch aiming the right turn signal triggering will be

toggled after 15 seconds has passed, so the hi-beam indicator will flash

before the

50 second mark is reached. The technician will have to ignore that and continue

holding the button until the 50 second mark is reached to aim the camera

Clock and date settings:

This section refers to the buttons on the left side of the steering wheel.Note:

If no button is pressed for 15 seconds, this process will end.Note:

• Activate the analog clock on the top screen.

• Press and hold the “Source” button for 15 seconds until the hi-beam indicator

blinks twice, and then let go.

• Press and release the “Seek-Up” and “Seek-Down” buttons to toggle between

minutes, hours, days, months, and year.

• Once a choice is selected, press and release the “Volume-Up” or “Volume-

Down” buttons to adjust the settings.

• While changing the hour, press the “Source” button to toggle between 12 and

24 hour formats.

• Wait 15 seconds for the process to end.

Extra settings

Attention! If the interface loses power for any reason, the following steps will

need to be performed again. Also, if installing an ASWC-1 connect it after you

initialize and test the interface/radio, with the key in the off position.

• Turn the key (or push-to-start button) to the ignition position and wait until the

radio comes on.

Note:

If the radio does not come on within 60 seconds, turn the key to the

off position, disconnect the interface, check all connections, reconnect the

interface, and then try again.

• Turn the key to the off position, and then to the accessory position. Test all

functions of the installation for proper operation, before reassembling the dash.

Termékspecifikációk

Márka:	Axxess
Kategória:	nincs kategorizálva
Modell:	HDCC-02

Szüksége van segítségre?

Ha segítségre van szüksége Axxess HDCC-02, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók nincs kategorizálva Axxess

Axxess AX-MLOC-HD1 Útmutató

12 Szeptember 2024

Axxess AXI-RGB1 Útmutató

28 Augusztus 2024

Axxess AFSI-01 Útmutató

28 Augusztus 2024

Axxess GMRSAV Útmutató

28 Augusztus 2024

Axxess LC-BMRC-01 Útmutató

28 Augusztus 2024

Axxess AX-TOYCAM3 Útmutató

28 Augusztus 2024

Axxess AX-MITSUCAM Útmutató

28 Augusztus 2024

Axxess AX-TOYRSAV Útmutató

28 Augusztus 2024

Axxess HDCC-02 Útmutató

28 Augusztus 2024

Axxess AX-TOYCAM2 Útmutató

28 Augusztus 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

Roland SD-20 Útmutató

16 Október 2024

SilverCrest SRG 1300 C3 Útmutató

16 Október 2024

IFM TY0058 Útmutató

16 Október 2024

Thule Kit 186039 Útmutató

16 Október 2024

Blumfeldt Solidflor Útmutató

16 Október 2024

Dimplex QRAD200E Útmutató

16 Október 2024

DAS Audio AX-112-5 Útmutató

16 Október 2024

Ferplast Ergocomfort Freetime Útmutató

16 Október 2024

AEG MECK52 Útmutató

16 Október 2024

Black Diamond BD1121530000ALL1 Útmutató

16 Október 2024