Használati útmutató Aube TH232-AF-230

Aube Termosztát TH232-AF-230

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Aube TH232-AF-230 (4 oldal) a Termosztát kategóriában. Ezt az útmutatót 169 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/4

TH232-AF-230 400-232-003-B 2010-05-26 1/4

• One (1) thermostat

• One (1) floor sensor

• One (1) wall plate

Turn off power to the heating system at the main power panel to

avoid electrical shock. Installation should be carried out by an

electrician.

 All work must conform to the applicable country standards for

electrical installations and wiring.

 This thermostat should be connected on a circuit equipped with

a fuse or a circuit breaker. It must be installed on a certified

electrical box equipped with non-metallic cable strain relief

adapters. Use separate adapters for the high-voltage wires and

for the sensor cable.

 For a new installation, choose a location about 1.5 m above the

floor.

 For electric baseboards, convectors and fan-forced heaters, the

thermostat must be installed facing the heating system and on

an inside wall.

 Avoid locations where there are air drafts (top of staircase, air

outlet), dead air spots (behind a door), direct sunlight or

concealed chimneys or stove pipes.

NOTE: The terminals are designed to handle a cross-section of wire

measuring 0.33 to 3.1 mm2.

Loosen the captive screw underneath the base and remove the

faceplate from the base.

Before making the connections, make sure

that the base covers the electrical box

entirely. If not, install a wall plate at the

back of the base.

Connect the wires:

• :Power

Terminals 1 & 5

• Load:

Terminals 2 & 4

see note 1

• Pilot Wire:

Terminal 3

see note 2

• :Floor sensor

Terminals 6 & 7

(no polarity)

see note 3

WARNING: Ensure that the wires are tightly secured to the terminals.

Apply a minimum torque of 0.5 Nm (4.4 Lb/in) when tightening the

screws.

Note 1 If a contactor is used between the thermostat and the load,

install a snubber at the contactor’s coil terminal to ensure

the proper operation of the thermostat.

Note 2 This connection is required on some models only.

Note 3 The sensor cable must pass outside the electrical box and

travel inside the wall to the floor. For the proper operation of

the thermostat, the floor sensor must be centered between

two heater wires having a maximum temperature of 80 °C

(176 °F). The floor sensor wire must not cross any heater

wire or be placed close to it.

Push wires into the electrical box and

secure the base to the electrical box

anchorage. The head of the screw

must be less than 2 mm thick.

Return the faceplate

to the base.

 Return power to the heating system.

NOTE: Keep the thermostat's air vents clean and unobstructed at all

times.



 1.



 2.



 3.

Base

Faceplate

TH232-AF-230 400-232-003-B 2010-05-26 2/4

This thermostat provides the following temperature control modes:

Display

Apply power to the thermostat at the main electrical panel. At

power-up, the thermostat is in manual mode and displays the

actual (measured) temperature. The setpoint temperature is 28 °C

(82 °F).

LO The actual temperature is below 0 °C (32 °F).

HI The actual temperature is above 70 °C (158 °F).

Er The thermostat built-in sensor is defective. Replace the

thermostat.

E1 The floor sensor circuit is opened. Check the sensor

connections.

E2 The floor sensor circuit is shorted. Replace the sensor.

Press and hold the Clear button for 3 seconds. The current con-

trol mode is displayed ( )ctl .

Press the to select between A, AF and F.

NOTE

: If you have chosen the A or F mode, go to step 7. If you have

chosen the AF mode, the thermostat will control the ambient tempera-

ture while keeping the floor temperature within desired limits. If the

floor temperature is too low or too high, the thermostat will turn heating

on or off to maintain the floor temperature within the limits regardless

of the ambient temperature. The minimum and maximum floor temper-

ature limits are factory-set at 5 °C (41 °F) and 28 °C (82 °F) respec-

tively. To modify the limits, continue with the next step:



Press the

Clear

button briefly. The minimum limit is displayed (

FL:LO

Press the button to set the minimum limit.



Press the

Clear

button briefly. The maximum limit is displayed (

FL:HI

Press the buttons to set the maximum limit.

Press the Mode/Return button to exit and

save the changes.

NOTE: If no button is pressed for 60 seconds, the thermostat will

save the changes and return to normal display.

This procedure allows you to choose the following configurations:

Press and hold the Pgm button for 3 seconds. The current tem-

perature unit is displayed (unit).

Press the to toggle between °C and

°F.

Press the Pgm button briefly. The current time format is dis-

played (Hr).

Press the to toggle between 24H and 12H.

Press the Pgm button briefly. The current Early Start setting is

displayed (ES).

Press the to toggle between OFF and On.

Press the Mode/Return button to exit and

save the changes.



 1.

A mode:  controls and displays the ambient air temperature

F mode:  controls and displays the floor temperature using

an external temperature sensor (default mode)

AF mode:  controls and displays the ambient air temperature

 maintains the floor temperature within desired

limits using an external temperature sensor



 2.



 3.

Day and

time setting

Schedule

programming

Mode selection /

Exit

Clear

Temperature

adjustment

Temperature

presets

On/Off button *

* Use this button to disable heating (e.g. in the summer). The

thermostat remains powered and continues to display the time

and temperature.

Time

Day

Temperature

Periods

Heating intensity

indicator

Automatic mode

Appears when the

setpoint temperature

is displayed

Appears when

heating is disabled

Mode indicator (A, F or AF)

Preset temperature

indicators

Manual mode



 4.

Parameters Default settings

Temperature format °C

Time format 24H

Early Start setting (see the note below) On

TH232-AF-230 400-232-003-B 2010-05-26 3/4

NOTE: Early Start can be used in Automatic mode only. When this

function is set to On, the thermostat calculates the optimal time to

start heating in order to obtain the desired temperature by the set

time. The thermostat re-assesses the start time daily based on the

previous day’s results.

Press the button to set the hour.Hour

Set the Min button to set the minutes.

Set the Day button to set the day.

Press Mode/Return to exit and save the changes.

Daylight Savings (DLS) Time

When the DLS function is set to US, the thermostat switches to Day-

light Savings Time on the second Sunday of March and to normal

time on the first Sunday of November.

When the DLS function is set to Eu, the thermostat switches to Day-

light Savings Time on the last Sunday of March and to normal time

on the last Sunday of October.

NOTE: The DLS function is OFF (default setting) when the clock

loses its setting.

Press the Day button (3 seconds) until DLS appears

on the screen.

Press the to toggle between US, Eu

and OFF.

Press the Day button briefly. The year setting is dis-

played.

Press the to set

the current year.

Press the Day button briefly. The month setting is dis-

played.

Press the to set the current month.

Press the Day button briefly. The date setting is dis-

played.

Press the to set the current date.

Press Mode/Return to exit and save the changes.

The thermostat normally displays the actual (measured) temperature.

To view the setpoint, press one of the buttons once. The setpoint

will appear for the next 5 seconds.

To change the setpoint, press one of the buttons until the desired

temperature is displayed. To scroll faster, press and hold the button.

Backlight

The screen is lit for 12 seconds when any button is pressed.

The thermostat has 2 preset temperatures:

 Comfort temperature

 Economy temperature

To use a preset temperature, press the corresponding button. The

corresponding icon will be displayed.

The following table shows the intended use and the default value of

each of the preset temperatures.

To store a preset temperature:

Set the desired temperature using the buttons.

Press and hold the corresponding temperature preset button

until the corresponding icon is displayed.

The thermostat has 2 modes of operation: automatic mode and man-

ual mode.

Use automatic mode if you want the thermostat to fol-

low the programmed schedule. The schedule has 4

time periods and uses the 2 preset temperatures. The

thermostat switches to Comfort temperature in periods

1 and 3 and to Economy temperature in periods 2 and

4. The following table shows the intended use of each

time period.

To use the automatic mode, press the Mode button to display on

the screen. The current period number will also appear.

Preprogrammed schedule

The thermostat has been programmed with the following schedule.

Temporary bypass

You can override the temperature of the current period by pressing

the , or buttons. The new setpoint will be used until the begin-

ning of the next period. The clock icon flashes during the bypass.

To cancel the bypass, press the Mode button.



 5.



 6.

Icon Intended use A/AF modes F mode

Comfort

(when at home) 21 °C (70 °F) 28 °C (82 °F)

Economy (when asleep

or away from home) 16.5 °C (62 °F) 20 °C (68 °F)



 7.

Period Temperature setting Typical use

Comfort Wake-up

Economy At work

Comfort At home

Economy Sleep

Period Temperature

setting

Period start time

MO TU WE TH FR SA SU

Comfort 6:00

6:00

Economy 8:30

8:30

am --:-- --:--

Comfort 4:00

4:00

pm --:-- --:--

Economy 11:00

11:00

Termékspecifikációk

Márka:	Aube
Kategória:	Termosztát
Modell:	TH232-AF-230

Szüksége van segítségre?

Ha segítségre van szüksége Aube TH232-AF-230, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Termosztát Aube

Aube TH115 AF Útmutató

23 Július 2024

Aube TH106 Útmutató

14 Július 2024

Aube TH232-AF-230 Útmutató

5 Július 2024

Aube TH132 A Útmutató

5 Július 2024

Aube TH132 F Útmutató

3 Július 2024

Útmutatók Termosztát

Legújabb útmutatók Termosztát

Amfra Thermic Control 77 Útmutató

9 Április 2025

UPM THM101A Útmutató

7 Április 2025

Jablotron TP-80 Útmutató

7 Április 2025

Eberle INSTAT 868-a6 Útmutató

6 Április 2025

Theben RAMSES 818 top 6A Útmutató

6 Április 2025

Sorel RC21 Útmutató

6 Április 2025

Hoffman ATEMNO Útmutató

5 Április 2025

Vaillant VRC calormatic UBW Útmutató

4 Április 2025

Eberle RTR-E 6145 Útmutató

4 Április 2025

Honeywell T87M1011 Round Modulation Útmutató

3 Április 2025