Használati útmutató Ashland EP45

Ashland Vízszivattyú EP45

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Ashland EP45 (36 oldal) a Vízszivattyú kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/36

• Thank you for purchasing this pump. Take the time to

read the instructions carefully before using this

product. We strongly recommend that you keep this

instruction manual in a safe place for future reference.

• Please refer to our website and the Products Center for

additional installation and operation instructions and

replacement parts information.

OPERATION, PERFORMANCE,

SPECIFICATIONS and PARTS MANUAL

EP40 & EP45

4/10 & 1/2 HP Efﬂuent Pumps

Efﬂuent

Pump

Models

EP40

& EP45

Series

“Danger” indicates an

imminent hazardous situation

which, if not avoided, WILL result in death or

serious injury.

“Caution” indicates a

potentially hazardous situation

which, if not avoided, MAY result in minor or

moderate injury.

WARNING

CAUTION

DANGER

“Warning” indicates an

imminent hazardous situation

which, if not avoided, MAY result in death or

serious injury.

MARKS AND MEANING:

DANGER

Before installation, read the following instructions care-

fully. Failure to follow instruction and safety information

could cause serious bodily injury, death and/or property

damage. Each Ashland Pump is individually factory tested

to ensure proper performance. Closely following these

instructions will eliminate potential operating problems

assuring years of trouble-free service.

Most accidents can be avoided by using common sense.

IMPORTANT - Ashland Pump is not responsible for

losses, injury or death resulting from failure to observe

these safety precautions, misuse, abuse or misapplica-

tion of pumps or equipment.

All returned products must

be cleaned, sanitized, or

decontaminated prior to shipment, to

insure employees will not be exposed to

health hazards in handling said materials.

All applicable laws and regulations shall apply.

Bronze/brass fitted pumps may

contain lead levels higher than con-

sidered safe for potable water systems. Government

agencies have determined that leaded copper alloys

should not be used in potable water applications.

Installation, wiring, and junction

connections must be in accord-

ance with the National Electric Code and all applicable

state and local codes. Requirements may vary depend-

ing on usage and location.

Installation and servicing is to be

conducted by qualiﬁed personnel only.

Rotating machinery, amputation

or severe lacerations can result.

Keep clear of suction and discharge

openings. DO NOT insert fingers into pump

with power connected.

Always wear eye protection when

working on pumps. Do not wear loose

clothing that may become entangled in moving parts.

Pumps build up heat and

pressure during operation.

Allow time for pumps to cool before handling or ser-

vicing.

Hazardous Voltage can shock,

burn or cause death. This pump is

not intended for use in swimming pools or

water installations where human contact with

pumped fluid is possible.

Risk of electrical shock. To

reduce risk of electrical shock,

always disconnect pump from source

before handling. Lock out power & tag.

Efﬂuent Pumps

Model: EP40 & EP45 Series

General Safety Information

WARNING

Do Not use these pumps in water

over 145°F. Do not exceed manu-

factures recommended maximum performance, as this

could cause the motor to overheat.

WARNING

DANGER

These pumps are NOT to be

installed in locations classified

as hazardous in accordance with the

National Electric Code, ANSI/NFPA 70.

WARNING

Effluent pumps often handle

materials which could cause illness

or disease. Wear adequate protective clothing when

working on a used pump or piping. Never enter a ba-

sin after it has been used.

WARNING

Do not introduce into any sewer,

either directly, or through a kitchen

waste disposal unit or toilet: Seafood Shells, Aquarium

Gravel, Cat Litter, Plastic Objects, Sanitary Napkins or

Tampons, Diapers, Rags, Disposable Wipes or Cloth,

Medications, Flammable Material, Oil or Grease,

Strong Chemicals, Gasoline.

DANGER

Do not lift, carry or hang pump by

the electrical cables. Damage to

the electrical cables can cause shock, burns or

death. Never handle connected power cords

with wet hands. Use appropriate lifting device.

DANGER

Failure to permanently ground the

pump, motor and controls before

connecting to power can cause shock, burns

or death.

DANGER

Make sure lifting handles are securely

fastened each time before lifting.

CAUTION

• Operation against a closed discharge valve will cause

premature bearing and seal failure on any pump.

• Any wiring of pumps should be performed by a

qualiﬁed electrician.

• Cable should be protected at all times to avoid

punctures, cuts, bruises, and abrasions-inspect

frequently.

• Never handle connected power cords with wet hands.

• Never let cords or plugs lie in water outside the sump

pit.

• These pumps are offered in a three phase and single

phase wiring conﬁguration. Voltages will vary

according to the application and can be seen in the

tables in this manual.

Efﬂuent Pumps

Model: EP40 & EP45 Series

Speciﬁcations

IMPORTANT

Prior to installation, record Model Number,

MFG Date, Amps, Voltage, Phase and HP,

from pump nameplate for future reference.

Also record the voltage and current readings

at startup:

Model Number:

MFG Date:

HP:

SN:

1 Phase Models

Amps: Volts:

SPECIFICATIONS

Overall Size Pump Material

(inches) Motor

Model HP Volt Ph Amps L W H Volute Housing Impeller Shaft

EP40M1-20 4/10 115 1 9.0 9.8 7 13.7 Cast Iron Cast Iron Cast Iron SS

EP40M2-20 4/10 230 1 4.5 9.8 7 13.7 Cast Iron Cast Iron Cast Iron SS

EP45M1-20 1/2 115 1 11.0 9.8 7 13.7 Cast Iron Cast Iron Cast Iron SS

EP45M2-20 1/2 230 1 5.5 9.8 7 13.7 Cast Iron Cast Iron Cast Iron SS

Note: All dimensions have a tolerance of + 1/8”

Description: To pump domestic,

commercial and light

industrial sewage

Physical Data:

DISCHARGE SIZE 2” NPT

IMPELLER TYPE Vortex, Cast Iron

CABLE LENGTH 20’

Liquid Handling:

SOLIDS SIZE 3/4”

ACCEPTABLE PH RANGE 6-8

Temperature:

MAXIMUM STATOR 130°C

MAXIMUM LIQUID TEMP. 104°F - Intermittent

Technical Data:

POWER CORD TYPE SJTW 16/3C

MOTOR HOUSING Cast Iron

VOLUTE Cast Iron

IMPELLER Cast Iron

MOTOR SHAFT 416SST

HARDWARE SST

“O” RINGS NBR

SEALS Single Mechanical

Carbon Ceramic

UPPER BEARING 6000

LOWER BEARING 6203

2” NPT

13.7”

4.2”

4.8”

7”

9.8”

Termékspecifikációk

Márka:	Ashland
Kategória:	Vízszivattyú
Modell:	EP45

Szüksége van segítségre?

Ha segítségre van szüksége Ashland EP45, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Vízszivattyú Ashland

Ashland SPV50 Útmutató

20 Augusztus 2024

Ashland EP45 Útmutató

20 Augusztus 2024

Ashland SPV33 Útmutató

20 Augusztus 2024

Ashland SW50 Útmutató

20 Augusztus 2024

Ashland SW50WB2424 Útmutató

20 Augusztus 2024

Ashland UT56 Útmutató

20 Augusztus 2024

Útmutatók Vízszivattyú

Legújabb útmutatók Vízszivattyú

Einhell Royal TMP 550-iS Útmutató

8 December 2024

Einhell Royal TP 260/1 Útmutató

8 December 2024

Einhell RG-GP 1355 NM Útmutató

8 December 2024

Einhell BG-GP 1146 NM Útmutató

8 December 2024

Einhell RGP 1300 Niro Útmutató

8 December 2024

Einhell RGP 1100 Niro Útmutató

8 December 2024

Einhell GPK 1500 Niro Útmutató

8 December 2024

Bavaria BDP 3530 Útmutató

6 December 2024

Bavaria BGP 830 Útmutató

6 December 2024

Bavaria BWW 830 Útmutató

6 December 2024