Használati útmutató Artusi CAID604KX

Artusi sütő CAID604KX

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Artusi CAID604KX (2 oldal) a sütő kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
PRODUCT OVERVIEW
TECHNICAL DATA
Top View
Please read the instruction manual carefully before operating your new hob.
Model Power supply
AC 220-240V
50-60Hz
Size (mm) Built-in hole Size
(mm)
592x522x90 560x490
1800W
/1200W
(Boost 2100W) (Boost 1500W)
Power
Heating area
(210mm)
Heating area
(180mm)
Heating area
(140mm)
Good Bad Bad Bad Bad Bad Bad
(recessed base) (convex base) (undersize) (oversize) (moisture on hotplate) (no utensil)
Power level
Default working timer (hour)
1
8
2
8
3
8
4
4
5
4
6
4
7
2
8
2
9
2
Before using your New Induction Hob
• Read this guide, taking special note of the ‘Safety Warnings’ section.
• Remove any protective film that may still be on your Induction hob.
If the display flashes “ ” alternately with the heat setting
This means that:
• you have not placed a pan on the correct cooking zone or,
• the pan you’re using is not suitable for induction cooking or,
• the pan is too small or not properly centred on the cooking zone.
No heating takes place unless there is a suitable pan on the cooking zone.
The display will automatically turn off after 1 minutes if no suitable pan is placed on it.
When You Have Finished Cooking
1.Turn the knob counterclockwise to " 0 "position, the corresponding heating zone display will flash “ for 5s, then stop heating.
Note:The knob is forbidden to directly adjust clockwise from P to 0.
2. Beware of hot surfaces indicator “H”will show which cooking zone is hot to touch. It will disappear when the surface has
cooled down to a safe temperature. It can also be used as an energy saving function - if you want to heat further pans, use the
hotplate that is still hot.
Choosing the right Cookware
• Only use cookware with a base suitable for induction cooking. Look for the induction symbol on the packaging
or on the bottom of the pan.
• You can check whether your cookware is suitable by carrying out a magnet test. Move a magnet towards the
base of the pan. If it is attracted, the pan is suitable for induction.
• If you do not have a magnet:
1. Put some water in the pan you want to check.
2. If “ ” does not flash in the display and the water is heating, the pan is suitable.
• Cookware made from the following materials is not suitable: pure stainless steel, aluminium or copper without
a magnetic base, glass, wood, porcelain, ceramic, and earthenware.
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as the cooking
zone. Use pans whose diameter is as large as the graphic of the zone selected.Using a pot a slightly wider
energy will be used at its maximum efficiency.If you use smaller pot efficiency could be less than expected.Pot
less than 140 mm could be undetected by the hob. Always centre your pan on the cooking zone.
Always lift pans off the Induction hob – do not slide, or they may scratch the glass.
1 2
3
CAID604K
862x522x90 835x490
1800W 1200W
(Boost 2100W)
1800W
(Boost 2100W) (Boost 1500W)
CAID905K
CAID604K CAID905K
1800W
(boost 2100W)
1800W
(boost 2100W)
1800W(boost 2100W)
(boost 1500W)
1200W
(boost 1500W)
Knob ON/OFF Control Knob ON/OFF Control
1200W
(boost 1500W)
1200W
1800W
(boost 2100W)
1800W
(boost 2100W)
(boost 1500W)
1200W
Congratulations on the purchase of your new Induction Hob.
We recommend that you spend some time to read this Instruction / Installation Manual in order to fully understand how to
install correctly and operate it.
For installation, please read the installation section.
Read all the safety instructions carefully before use and keep this Instruction / Installation Manual for future reference.
Safety Warnings
Your safety is important to us. Please read this information before using your cooktop.
Installation
Electrical Shock Hazard
• Disconnect the appliance from the mains electricity supply before carrying out any work or maintenance on it.
• Connection to a good earth wiring system is essential and mandatory.
• Alterations to the domestic wiring system must only be made by a qualified electrician.
• Failure to follow this advice may result in electrical shock or death.
Cut Hazard
• Take care - panel edges are sharp.
• Failure to use caution could result in injury or cuts.
Important Safety Instructions
• Read these instructions carefully before installing or using this appliance.
• No combustible materials or products should be placed on this appliance at any time.
• Please make this information available to the person responsible for installing the appliance.
• In order to avoid a hazard, this appliance must be installed according to these instructions for installation.
• This appliance must be installed and earthed only by a suitably qualified person.
• This appliance should be connected to a circuit which incorporates an isolating switch, providing full disconnection from the
power supply.
• Failure to install the appliance correctly could invalidate any warranty or liability claims.
Operation and Maintenance
Electrical Shock Hazard
• Do not cook on a broken or cracked cooktop. If the cooktop surface should break or crack, immediately switch off the
appliance at the mains power supply (wall switch) and contact a qualified technician.
• Switch the cooktop off at the wall before cleaning or maintenance.
• Failure to follow this advice may result in electrical shock or death.
Health Hazard
• This appliance complies with electromagnetic safety standards.
• However, persons with cardiac pacemakers or other electrical implants (such as insulin pumps) must consult with their
doctor or implant manufacturer before using this appliance to make sure that their implants will not be affected by the
electromagnetic field.
• Failure to follow this advice may result in death.
Hot Surface Hazard
• During use the appliance becomes hot. Care should be taken to avoid touching heating elements inside the oven.
• Do not let your body, clothing or any item other than suitable cookware contact the induction glass until the surface is cool.
• Metallic since objects such as knives, forks, spoons and lids should not be placed on the hob surface they can get hot.
• Keep children away.
• Handles of saucepans may be hot to touch. Ensure that the saucepan handles do not overhang other cooking zones that
are switched on. Make sure children can’t reach the cookware handles.
• Failure to follow this advice could result in burns and scalds.
Cut Hazard
• The razor-sharp blade of a cooktop scraper is exposed when the safety cover is retracted. Use with extreme care and
always store safely and out of reach of children.
• Failure to use caution could result in injury or cuts.
Important Safety Instructions
• Never leave the appliance unattended when in use. Boil-over causes smoking and greasy spillovers may ignite.
• Never use your appliance as a work or storage surface.
• Never leave any objects or utensils on the appliance.
• Do not place or leave any magnetisable objects (e.g. credit cards, memory cards)or electronic devices (e.g. computers, MP3
players) near the appliance as they may be affected by its electromagnetic field.
• Never use your appliance for warming or heating the room.
• After use, always turn off the cooking zones and the cooktop as described in this manual (i.e. by using the touch controls). Do
not rely on the pan detection feature to turn off the cooking zones when you remove the pans.
• Do not allow children to play with the appliance nor sit, stand or climb on it.
• Do not store items of interest to children in cabinets above the appliance. Children climbing on the cooktop could be seriously injured.
• Do not leave children alone or unattended in the area where the appliance is in use.
• Children or persons with a disability which limits their ability to use the appliance should have a responsible and competent
person to instruct them in its use. The instructor should be satisfied that they can use the appliance without danger to
themselves or their surroundings.
• Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should
be done by a qualified technician.
• Do not use a steam cleaner to clean your cooktop.
• Do not place or drop heavy objects on your cooktop.
• Do not stand on your cooktop.
• Do not use pans with jagged edges or drag pans across the induction glass surface as this can scratch the glass.
• Do not use scourers or any other harsh abrasive cleaning agents to clean your cooktop as these can scratch the induction glass.
•This appliance is intended to be used in a household or similar environments such as staff kitchen areas in shops, offices and
other residential environments.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in
order to avoid a hazard.
•the appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction.
•children being supervised not to play with the appliance.
•Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot.
•After use, switch off the hob element by its control and do not rely on the pan detector.
•WARNING: The appliance and its accessible parts become hot during use.
Care should be taken to avoid touching heating elements.
•WARNING: Unattended cooking on the hob with fat or oil can be dangerous and may result in a fire. NEVER try to extinguish
such fire with water, rather switch off the appliance and then cover the flame with a lid or a fire blanket.
•WARNING: Do not store items on the cooking surfaces as this presents a fire hazard.
•WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of an electric shock.
•The appliance is not intended to be operated by means of an external timer or separate remote-control system.
CAUTION: The cooking process has to be supervised.
WARNING: In order to prevent tipping of the appliance, it must be stabilised prior to installation. Please refer to the installation instructions.
WARNING:Only use hob guards that are either provided or deemed suitable by the manufacturer for use with this induction hob.
The use of inappropriate guards can cause accidents. The use of inappropriate guards can cause accidents.
This appliance incorporates an earth connection for functional purposes only.
WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire. NEVER try to extinguish a fire
with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.
WARNING: Danger of fire: do not store items on the cooking surfaces.
CAUTION: The cooking process has to be supervised. A short term cooking process has to be supervised continuously.
NOTICE: The crystallite glass is still hot after use, please do not touch!
POWER LIMIT WORKING MODE (CAID905K)
All 5 zones cannot be operated simultaneously on full power as it would exceed the power limit.
The left two heating zones can operate on the full power setting. The right two and the middle heating zones, if operated
simultaneously, exceed 3600W. This means when selecting the higher settings for these zones, they will adjust automati-
cally to ensure the total power is less than 3600W.
Boost Control
Turn the knob clockwise to the "P "position, the corresponding heating zone will enter the BOOST function,
the display will show " " , the BOOST function can run for up to 5 minutes, after 5 minutes, the power will
automatically drop to the 9 level, the display will show " " .
To start cooking
Note Before power on, the knobs must be adjusted to the "0 " position.：
1. Touch the ON/OFF control.
• With the power switched on, the buzzer will beep once, all displays will show “–”, indicating that the
induction hob has entered standby mode.
2. Place a suitable pan on the cooking zone that you wish to use.
• Make sure the bottom of the pan and the surface of the cooking zone are clean and dry.
3.Power level setting
• Turn the knob clockwise to the required power level (1~P), the corresponding heating zone display will
flash the selected level for 5s, then start to work.
Note:The knob is forbidden to directly adjust counterclockwise from 0 to P .
• If you don’t choose a heat setting within 1 minute, the induction hob will automatically switch off. You will
need to start again at step1.
• You can modify the heat setting at any time during cooking.
Overheating Protection
The appliance is equipped with a temperature sensor which can monitor the temperature inside the induction hob.
When an excessive temperature is monitored, the Induction hob will stop operation automatically.
Detection of Small Articles
When an unsuitably sized or non-magnetic pan (e.g. aluminium), or some other small item (e.g. knife, fork, key) has
been left on the hob, the display flashes “ ” and the hob will automatically go in the standby mode in 1 minute. The
fan will keep cooling down the induction hob for a further 2 minutes.
Auto Shutdown Protection
Auto shutdown is a safety protection function for your induction hob. It will automatically turn off after a certain period of
time. The default working times for various power levels are shown in the below table:
Heat setting Suitability
1-2
3-4
5-6
7-8
9
● Delicate warming for small amounts of food
● Melting chocolate, butter, and foods that burn quickly
● Gentle simmering ● Slow warming
● Reheating ● Rapid simmering ● Cooking rice
● Pancakes
● Cooking pasta
● Stir-frying ● Searing ● Bringing soup to the boil ● Boiling water
Cooking Guidelines
Take care when frying as the oil and fat heat up very quickly, particularly if you’re using PowerBoost.
At extremely high termperatures oil and fat will ignite spontaneously and this presents a serious fire risk.
Heat Settings
The settings below are guidelines only. The exact setting will depend on several factors, including your cookware and the
amount you are cooking. Experiment with the induction hob to find the settings that best suit you.
V20231216
Cod 0070305158-C：
Care and cleaning
1. Everyday soiling on glass (fingerprints, marks, stains left by food of non-sugary spillovers on the glass).
1)Switch the power to the cooktop off;
2)Apply a cooktop cleaner while the glass is still warm (but not hot!)
3)Rinse and wipe dry with a clean cloth or paper towel.
4)Switch the power to the cooktop back on.
● When the power to the cooktop is switched off, there will be no hot surface indication but the cooking zone may
still be hot! Take extreme care.
● Heavy-duty scourers, some nylon scourers and harsh/abrasive cleaning agents may scratch to check if your
cleaner or scourer is suitable.
● Never leave cleaning residue on the cooktop: the glass may become stained.
2. Boilovers, melts, and hot sugary spills on the glass
Remove these immediately with a fish slice, palette knife or razor blade scraper suitable for induction glass cooktops, but
beware of hot cooking zone surfaces:
1). Switch the power to the cooktop off at the wall.
2). Hold the blade or utensil at a 30°angle and scrape the soiling or spill to a cool area of the cooktop.
3). Clean the soiling or spill up with a dish cloth or paper towel.
4). Follow steps 2 to 4 for everyday soiling on glass above.
● Remove stains left by melts and sugary food or spillovers as soon as possible. If left to cool on the glass, they
may be difficult to remove or even permanently damage the glass surface.
● Cut hazard: then the safety cover is retracted, Use with extreme care and always store safely and out of rech
of children.
Hints and Tips
1. The induction hob cannot be turned on.
NOTE:
NOTE:
May be there is no power: Make sure the induction hob is connected to the power supply and that it is switched on.
Check whether there is a power outage in your home or area. If you’ve checked everything and the problem persists,
call a qualified technician.
2. The glass is being scratched.
Tough-edged cookware. Unsuitable, abrasive scourer or cleaning products being used: Use cookware with flat and
smooth bases. See choosing the right cookware. See “Care and cleaning”.
3. Some pans make crackling or clicking noises.
This may be caused by the construction of your cookware (layers of different metals vibrating differently): This is normal,
but the noise should quieten down or disappear completely.
4. The induction hob makes a low humming noise when used on a high heat setting.
This is caused by the technology of induction cooking: This is normal, but the noise should quieten down or disappear
completely when you decrease the heat setting.
Failure Display and Inspection
If an abnormality comes up, the induction hob will enter the protective state automatically and display
corresponding protective codes:
!
Installation
Selection of installation equipment
Cut out the work surface according to the sizes shown in the drawing.
For the purpose of installation and use, a minimum of 5 cm space shall be preserved around the hole.
Be sure the thickness of the work surface is at least 30mm. Please select heat-resistant work surface material to avoid
larger deformation caused by the heat radiation from the hotplate. As shown below:
L(mm) W(mm) H(mm) D(mm) A(mm) B(mm) X(mm)
592 522 65 56 560 490 50 mini
L(mm) W(mm) H(mm) D(mm) A(mm) B(mm) X(mm)
862 522 65 56 835 490 50 mini
Under any circumstances, make sure the Induction cooker hob is well ventilated and the air inlet and outlet are not blocked.
Ensure the Induction cooker hob is in good work state. As shown below
Note: The safety distance between the hotplate and the cupboard above the hotplate should be at least 600mm.
The above are the judgment and inspection of common failures.
Please do not disassemble the unit by yourself to avoid any dangers and damages to the induction hob.
Before you install the hob, make sure that
• the work surface is square and level, and no structural members interfere with space requirements
• the work surface is made of a heat-resistant material
• if the hob is installed above an oven, the oven has a built-in cooling fan
• the installation will comply with all clearance requirements and applicable standards and regulations
• a suitable isolating switch providing full disconnection from the mains power supply is incorporated in the permanent wiring,
mounted and positioned to comply with the local wiring rules and regulations.
The isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active
[phase] conductors if the local wiring rules allow for this variation of the requirements)
• the isolating switch will be easily accessible to the customer with the hob installed
• you consult local building authorities and by-laws if in doubt regarding installation
• you use heat-resistant and easy-to-clean finishes (such as ceramic tiles) for the wall surfaces surrounding the hob.
5. Fan noise coming from the induction hob.
A cooling fan built into your induction hob has come on to prevent the electronics from overheating. It may continue to run
even after you’re turned the induction hob off: This is normal and needs no action. Do not switch the power to the
induction hob off at the wall while the fan is running.
6. Pans do not become hot and appears “ ” in the display.
The induction hob cannot detect the pan because it is not suitable for induction cooking. The induction hob cannot detect
the pan because it is too small for the cooking zone or not properly centred on it: Use cookware suitable for induction
cooking. See section ‘Choosing the right cookware’.
Centre the pan and make sure that its base matches the size of the cooking zone.
7. The induction hob or a cooking zone has turned itself off unexpectedly, a tone sounds and an error code is
displayed (typically alternating with one or two digits in the cooking timer display).
Technical fault: Please not down the error letters and numbers, switch the power to the induction hob off at the wall, and
contact a qualified technician.
!
A(mm) B(mm) C(mm) D E
600 50 mini 20 mini Air intake Air exit 5mm ≥
F
>35mm
G
<50mm
D
E
A
C
BNote: There must be have a 560x5mm holes on front
of cooker top position E, to dissipate heat air.
>2cm
F
G
After hob is installed to worktop, make sure
the air flow hole is not blocked by worktop bottom
78
6
5
!
!
When you have installed the hob, make sure that
• the power supply cable is not accessible through cupboard doors or drawers
• there is adequate flow of fresh air from outside the cabinetry to the base of the hob
• if the hob is installed above a drawer or cupboard space, a thermal protection
barrier is installed below the base of the hob
• the isolating switch is easily accessible by the customer
Before locating the fixing brackets
The unit should be placed on a stable, smooth surface (use the packaging). Do not
apply force onto the controls protruding from the hob.
Adjusting the bracket position
Fix the hob on the work surface by screw 4 brackets on the bottom of hob(see picture) after installation.
Adjust the bracket position to suit for different table top thickness.
Cautions
1. The induction hotplate must be installed by qualified personnel or technicians. We have professionals at your service.
Please never conduct the operation by yourself.
2. The hob will not be installed directly above a dishwasher, fridge, freezer, washing machine or clothes dryer, as the
humidity may damage the hob electronics
3. The induction hotplate shall be installed such that better heat radiation can be ensured to enhance its reliability.
4. The wall a nd induced heating zone above the table surface shall withstand heat.
5. To avoid any damage, the sandwich layer and adhesive must be resistant to heat.
Connecting the hob to the mains power supply
This hob must be connected to the mains power supply only by a suitably qualified person.
Before connecting the hob to the mains power supply, check that:
1. the domestic wiring system is suitable for the power drawn by the hob.
2. the voltage corresponds to the value given in the rating plate.
3. the power supply cable sections can withstand the load specified on the rating plate.
To connect the hob to the mains power supply, do not use adapters, reducers, or branching devices, as they can cause
overheating and fire.
The power supply cable must not touch any hot parts and must be positioned so that its temperature will not exceed 75˚C
at any point.
Check with an electrician whether the domestic wiring system is suitable without alterations. Any alterations must only be
made by a qualified electrician.
The power supply should be connected in compliance with the relevant standard.The method of connection is shown
below.
WARNING:
Close the cable clamp after making the electrical connection. Close the terminal board cover by twisting it down.
Brackets
Problem
U
Possible causes What to do
The appliance
does not work Break in power supply
Please check the main power is normal; if the leakage protection switch is off; if there is a
blown fuse, replace it with a new one; if the main power is normal, check if the plug is connect
with socket appropriately; If the hob is wire connection type, disconnect the power, check if the
wire is loose; disconnect the power, check if main plug is off; Exclude above reasons, should be
appliance fault, send it to service center for repairing.
During heating,
the unit stop work. Delay off timer activates.
No pan or pan unsuitable
Input power too low
Input power too high
Thermistor of coil short circuit
Thermistor of coil open circuit
Too high temperature
of IGBT thermistor.
Too high temperature
of coil thermistor.
IGBT thermistor short circuit
IGBT thermistor open circuit
Please check if set delay off function. If set delay off function, the unit will stop once delay off
time out.
No pan, please put proper pan. PCB synchronization or drive circuit fault, please send the
appliance to service center for repairing.
E2
E1
F3
F4
E5
E3
F9
FA
Low voltage, voltage of the main power is less 180V. Please check if voltage of the main power
is normal. Once voltage of the main power returns normal, re-start the unit. Voltage of PCB fault,
please send the unit to service center for repairing.
High voltage, voltage of the main power exceeds 250V. Please check if voltage of the main
power is normal. Once voltage of the main power returns normal, re-start the unit. Voltage of
PCB fault, please send the unit to service center for repairing.
Sensor of coil thermistor connection error. Or detection part of PCB coil thermistor failure,
send to service center for reparing.
Too high temperature of IGBT thermistor, air outlet is blocked. Open air outlet, re-start the unit. If
still unsolved, it is possible that cooling fan connection error, cooling fan damaged, or drive circuit
of fan failure, send to service center for repairing. IGBT temperature sensor open circuit /short
circuit. Temperature detection part of PCB IGBT failure, send to service center for repairing.
Too high temperature on induction glass surface, please check if there is no water in pan. After
treatment, connect with power again. If still unsolved, it is possible that sensor of cooktop failure,
send to service center for repairing.
Senor of IGBT thermistor connection error. Or detection part of IGBT PCB sensor failure,
send to service center for repairing.
B
X
HD
LW
X
X
A
F
r
o
n
t
e
d
g
e
o
f
w
o
rk
to
p
R
e
a
r
w
a
l
l
SEAL
CAID604K
CAID604K
CAID905K
CAID905K
CONNECTION DIAGRAM
Caution! Voltage of heating
elements 220-240V Caution! In the event
of any connection the safety Wire
must be connected to the E terminal.
L1 N1 N2L2
E L N
L1 N1 N2L2
• If the cable is damaged or to be replaced, the operation must be carried out the by after-sale agent with dedicated tools to
avoid any accidents.
• The appliance for disconnection from the supply mains having a contact separation in all poles providing full disconnection
under overvoltage category III conditions should be provided in fixed wiring in accordance with the wiring rules.
• The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations.
• The cable must not be bent or compressed.
• The cable must be checked regularly and replaced by authorised technicians only.
L1 N1 N2L2
E L N
L1 N1 N2L2
3. Disassembly of the bottom base CAID905K（ ）
4 screws need to be removed first (see image) before the base can be disassembled.
The disassembly of the bottom base must be carried out by a qualified person.
Screws need to removed
By ensuring that this appliance is disposed of correctly, you will help prevent any possible harm to
The environment and to human health which might otherwise be caused if disposed of in the
wrong way.
The symbol on the product indicates that it may not be treated as normal household waste.
It should be taken to a collection point for the recycling of electrical and electronic goods.
For further information regarding the treatment, recovery and recycling of this product, please contact
your local council, household waste disposal service or the shop where you purchased the product.

Termékspecifikációk

Márka: Artusi
Kategória: sütő
Modell: CAID604KX

Szüksége van segítségre?

Ha segítségre van szüksége Artusi CAID604KX, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók sütő Artusi

Artusi

Artusi AO750MBP Útmutató

4 Január 2025
Artusi

Artusi AFIR935B Útmutató

2 Szeptember 2024
Artusi

Artusi CAO611 Útmutató

2 Szeptember 2024
Artusi

Artusi ACS45MB Útmutató

31 Augusztus 2024
Artusi

Artusi AFG913X/1 Útmutató

31 Augusztus 2024
Artusi

Artusi AFG915X/1 Útmutató

31 Augusztus 2024
Artusi

Artusi AFG999X Útmutató

29 Augusztus 2024
Artusi

Artusi AFG999W Útmutató

29 Augusztus 2024
Artusi

Artusi CAGH7000B Útmutató

29 Augusztus 2024
Artusi

Artusi AFG999B Útmutató

29 Augusztus 2024

Útmutatók sütő

Legújabb útmutatók sütő

Scarlett

Scarlett SC-EO93O18 Útmutató

3 Április 2025
Bertazzoni

Bertazzoni MAS100 6 MFE DXE Útmutató

3 Április 2025
AEG

AEG Competence 573 V W Útmutató

2 Április 2025
Samsung

Samsung BQ1AD4T243 Útmutató

2 Április 2025
Zanussi

Zanussi zhn 723 zht 74 kp Útmutató

2 Április 2025
Atag

Atag ox60 a Útmutató

2 Április 2025
Electrolux

Electrolux EON3010 Útmutató

2 Április 2025
De Dietrich

De Dietrich DOP790 Útmutató

2 Április 2025
Krefft

Krefft RGC 051M Útmutató

2 Április 2025
Stoves

Stoves SE60MFPTi Útmutató

2 Április 2025