Használati útmutató Artusi AGS411B

Artusi Mosogató AGS411B

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Artusi AGS411B (1 oldal) a Mosogató kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/1
Installation Instructions for Artusi Granitek Sinks
PACKAGING: All packaging materials (plastic bags, polystyrene foam,
etc.) are potentially dangerous and should be kept away from children.
1. HOLES FOR THE TAP CONNECTIONS
The sink comes to you with pre-prepared semi-bores of Ø 35 mm on both
sides. This lets you choose the side where you wish to install the tap. After
deciding which side you wish to use, the hole can be completed using a
DIAMOND CORE installed on a manual drill, taking care to work from the
non-visible side.
2. BORING THE WORK SURFACE FOR INSERTING THE SINK
Place the sink upside-down on the work surface where it is to be installed.
Trace around the outer edge of the sink using a pencil. Now move the sink
and draw a dotted line 1cm inside the one you have just drawn using the
sink as a template. Cut along the dotted line using the appropriate tools.
3. FITTING THE SINK INTO THE WORK SURFACE
All our sinks come equipped with pre-installed mounting clamps. The
following steps explain how to install the sink correctly: A special sealant
is supplied with the sink. Apply it all around the outer edge of the sink,
wherever it will come into contact with the work surface when the installation
is complete. Make sure that all the clasps of the fastenings are facing
inwards. Insert the sink into the cut-out area of the work surface making sure
it is centred. Tighten the fastenings using the adjusting screws, starting from
the centre and working in a criss-cross order.
INSTALLING THE DRAINAGE (DRAINS AND DRAIN-TRAPS)
Follow the instructions provided with the drain accessories.
UPKEEP AND CARE
Your sink will last longer if it is taken care of properly. Correct care also
helps to keep it looking attractive for a long time.
1. ROUTINE CARE
The best way to clean the sink is to use a soft cloth or sponge, with
commonly available detergents diluted in warm water. Strong detergents
should not be used. The surface of the sink should be washed with water,
drying the damp parts with a spongy cloth. This will help prevent the
formation of lime scale marks, especially on darker coloured sinks.
2. REMOVING STUBBORN STAINS
Traces of stubborn dirt can be removed with a cloth soaked in diluted bleach
or alcohol or, in extreme cases, with acetone. After this, rinse the surface
well with water.
3. SPECIAL CLEANING
The sink is composed of a mixture with a high percentage of inert llers that
make the product very hard and strong. This particular characteristic may
cause streaking due to the continual rubbing of metal pans. The streaks are
due to the release of small particles of metal, which can be removed with a
brush (like Scotch Brite), together with commonly used detergents.
4. FURTHER RECOMMENDATIONS
Do not use highly alkaline substances like ammonia or caustic soda. Do
not put pans or coffee-pots that have just been taken off the heat (which
sometimes reach 500°C) directly in the sink. Do not pour boiling oil into the
sink, as this could deform the drain pipes. Do not cut food directly in the
sink. Chopping boards should be used for this purpose. Lime scale residue
can be removed with vinegar or acetic acid. Do not put pans or coffee
pots that have just been taken off the heat (which sometimes reach 500°C)
directly in the sink.
artusi.com.au
All warranty service calls must be booked via the customer care department.
The team can be contacted on 1 300 85 64 11 option 1 or customercare@eurolinx.com.au

Termékspecifikációk

Márka: Artusi
Kategória: Mosogató
Modell: AGS411B

Szüksége van segítségre?

Ha segítségre van szüksége Artusi AGS411B, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek