Használati útmutató Archos PicoDrone
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Archos PicoDrone (168 oldal) a drón kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/168
Quick Start Guide
Safety Notice for Drone Battery
Please read the user handbook carefully and then keep it in a safe place
for future reference and maintenance.
- Only use the provided charger.
- When you install the battery, you must follow the electrode
instructions. It is not allowed to reverse the batteries, which can cause
short circuits.
- Non-rechargeable battery can’t be used, and the rechargeable battery
can only be charged under adult supervision.
- Different types of batteries (new and old) can’t be mixed
- Please contact your environmental government bureau to know how to
dispose and recycle Lipo batteries
- Please don’t overcharge the battery or leave the battery charging
alone.
- Don’t throw the battery into fire or put it in a high temperature
location, this may cause battery explosion
- The charger and battery are not toys.
- This product contains electronic components. Under water immersion
and humid environments are forbidden.
- Use dry cloth to wipe the surface
- Check the product regularly to see if there is any damage to the
components, if so please stop using until it has been repaired.
Do not put the battery in high temperature place, such as in the fire or
on a heating device to avoid damage or explosion.
Do not slam the battery on a hard surface.
Do not put the battery in water and keep it in dry place.
Do not open the battery.
Do not leave the battery without supervision when charging.
Make sure that there is no short circuit of the power wire.
Please use the recommended charger only.
Check the charger’s wire, plug, surface regularly. Do not
use any broken charger.
If you do not fly the drone at least once a week, maintain the
drone battery with about 50% power to keep its performance.
Charging Instructions for the Drone Battery
1. Connect the drone battery with USB cable first then
choose one of the methods as on the picture below
to connect with USB plug.
2. The red USB indicator light is on when charging and
the light turns green when fully charged( The switch
must be powered off when charging).
* For faster charging, it is recommended to use an
adapter with 5V 2A output current (not included) to
charge the battery
Phone charger
Power bank
Computer
charging
Car charger
Li-Po Battery Disposal & Recycling
Wasted Lithium-Polymer batteries must not be placed with
household trash. Please contact local environmental or waste
agency or the supplier of your model or your nearest Li-Po
battery recycling center.
Check List Before Your Flight
1. Make sure the drone’s battery and transmitter’s
battery are fully charged.
2. Make sure the left lever of the transmitter is in the
middle position.
3. Please strictly follow the instructions to turn on and
turn off before operation. Turn on the transmitter
power first and then turn on the drone power before
flying; turn off the drone power first and then turn off
the transmitter power when you are finishing flying.
Improper turn on and turn off order may cause the
drone to lose control and threaten people’s safety.
Please make sure you correctly turn on and turn off.
4. Make sure the connection is strong between battery
and motor etc. The ongoing vibration may cause bad
connection of power terminal and make the drone
lose control.
5. Improper use may cause drone to crash, which may
lead to motor defects and noise, and then affect the
flying status or even stop flying. Please go to the
local distributor to buy new replacement parts in
case of damage.
Instructions for Drone and Transmitter
Drone
Propeller
Guard
Front Camera Propeller Guard
Drone Cover
Housing
Propeller
Guard
Propeller Guard
Switch Rear
ON/OFF
Left Right
Front LED (Green)
Propeller B
Propeller B
Propeller A
Propeller A
Drone Bottom
Housing
Rear LED (Red)
Left lever Move the lever forward / backward / left / right to
y the drone up / down / turn left / turn right.
Right lever Move the lever forward / backward / left / right to
y the drone forward / backward / left / right.
Power Switch Push up the power switch to turn on the
transmitter, and pull
down to turn o.
Heading Hold
Mode
Press the button to enter heading hold mode, and
press again to
exit from heading hold mode.
High / Medium/
Low Speed Mode
Press down the Left lever to switch to High /
Medium/ Low Speed
Take O / Landing /
Emergency Stop
Button
Press the button and the drone will y up
automatically. Press the button again and the
drone will land on the ground automatically.
Press and hold the button more than 1s, the drone
propellers will stop and fall down immediately.
Trimmer mode
Button
Press down this button, move the right lever to the
required trimmer direction, then it will adjust the
direction accordingly, when loose the lever, then
ESC from the trimmer mode.
Installing the batteries:
Open the battery cover on the back side of the
transmitter and put 3 alkaline batteries (AAA, not
included) into the box in accordance with electrode
instructions, as picture shown.
Pre-ight Operation Instructions
Frequency Pairing
1. Turn on the transmitter switch (Picture 1) and the
power indicator light flashes rapidly. Push the Left
lever all the way down to the lowest position and
then release. The Left lever moves back to the middle
position automatically. (Picture 2 / 3) The power
indicator light flashes slowly, indicating the transmitter
is ready for frequency pairing.
Battery cover
3X1.5V
Alkaline Batteries
Notice:
1. Make sure the electrodes match.
2. Do not mix new with old batteries.
3. Do not mix dierent kinds of batteries.
4. Do not charge non rechargeable batteries.
Picture 1 Picture 3
Picture 2
2. Turn on the drone. (Picture 4)
3. Put the drone on a flat surface, the drone body lights
turn from flashing to solid bright, which indicates
successful frequency pairing.
Important Notice: Please make sure the drone is placed
on the horizontal position after powering on the drone,
so that the drone can work well.
Checklist before Flight
1. The camera is in front of the drone. Keep the drone
front away from you.
2. Power on the drone and check the direction of
the rotating propellers. The left front and right rear A
propellers rotating clockwise while the right front and
left rear B propellers rotating counterclockwise.
3. Move the Left Stick and Right Stick at the same
time as Picture 5 shown(45 degree inward) to start
the motors and repeat previous step again to lock the
motors.
Picture 4
4. After starting the motors, push up the left lever to
fly the drone slowly, and then pull down the left lever to
the lowest position slowly, then the drone lands on the
ground.
5. It’s recommended to repeat above Steps 4 to
practice.
6. Adjust relative transmitter Trimmer button to adjust
the rudder if the drone tilts to one side when flying.
Picture 5
Calibration Instructions
Please follow below steps to calibrate the drone if the
drone becomes imbalanced after crashing during the
flight, and can not be adjusted by trimmer button and
causes flight difficulties.
1. Turn off the drone, then turn off the transmitter
switch.
2. Turn on the transmitter switch, push the left lever all
the way down to the lowest position (Picture 6) and
then release. The left lever goes back to the middle
position automatically (Picture 7). The transmitter is
ready for frequency pairing mode.
Picture 6 Picture 7
3. Turn on the drone and put it on a flat surface in a
horizontal position. The drone’s body lights change
from flashing to solid bright, which indicates
successful frequency pairing.
4. Do not move the left lever before successful
calibration. Push the right lever
as Picture 8 shown and then
release. The drone’s body lights
flash, which indicates that
the drone is calibrating. When
the drone’s body lights become solid, the calibration
is complete.
Notice: If the drone crashes, the gyroscope can be
affected causing flight issues. If so, turn the power
off and on again to calibrate.
Flying Control
Notice: Every time before the drone takes off, move the
left lever and right lever at the same time as shown on
Picture 5(inward 45 degree) to start the motors. Push
up the left lever slowly to fly the drone or press down
the one button take off .
Picture8
=
Push the lever up, the
drone goes forward.
Pull the lever down, the
drone goes backward.
Turn the lever to the left,
the drone turns to left
Turn the lever to the right,
the drone turns to right
Right Stick
Functions Introduction
Two Take Off Methods
1. Method 1 (Take off) : After successful frequency
pairing, move the Left and Right levers at the same
time as shown Picture 5 (inward 45 degree) to start
the motors. Push up the Left lever to fly the drone to
a certain altitude and then release the lever.
2. Method 2 (One Button Take Off): Press the Take Off
/ Landing / Emergency Stop Button (Picture 9) , the
drone flies up automatically and keep flying at an
altitude of approximately 1.2 meters.
Landing Methods
1. Method 1 (Landing): Push the Left lever all the way
down to the lowest position(Picture 2/6) and hold
it till the motors stop and the drone will land on the
ground.
2. Method 2 (One Button Landing): Press the Take
Off / Landing / Emergency Stop Button once
shortly(picture 9), and the drone will land on the
ground automatically.
(When using this function, you can not touch the left
lever, if not, then the function will fail)
Picture 9
Take o/Landing/Emergency stop button
Emergency Stop: When the drone in emergency situation
and going to hit people or an obstacle etc., press the
Take Off / Landing / Emergency Stop Button
immediately and hold it for more than 1s. The propellers
will stop immediately.
Tip: Do not use the emergency stop function unless in emergency situation.
The drone will fall down suddenly after all propellers stop.
Altitude Hold Mode
Altitude hold mode indicates that the drone maintains a
consistent altitude while allowing roll, pitch, and yaw
to be controlled normally. It makes easier to control
the drone for beginner and more stable for aerial
photography.
Push the Left lever up (down) to fly the drone at a
certain altitude and then release the lever. The lever will
go back to the center position (Altitude Hold Center)
as Picture 10 shown. And the drone will keep flying at
current altitude. Repeat above steps if you want to
change the drone altitude (Default mode).
Picture 10
Altitude Hold Center
Picture 1 Picture 2
Prerequisite: Position the drone in such a way that its front is your front (see Picture 1). Tip:
Do not change the orientation of the transmitter (see Picture 2) after entering heading
hold mode. Front(camera)
To turn on Heading Hold Mode, press Heading Hold Mode
button and the drone LED lights flash, which indicates
the drone enters heading hold mode.
To turn off Heading Hold Mode, press Heading Hold Mode
button again and the drone LED lights turn solid, which
indicates the heading hold mode is off.
Low Battery Alarm
When the transmitter has low battery, the transmitter
will beep Di-di-di... to remind the user to land the drone
in order to replace the batteries as soon as possible. Or
the drone may lose control.
Heading Hold Mode Button
When the drone has low battery, the transmitter will
beep Di.di.di... constantly to remind the user to land the
drone as soon as possible.
Out of Range Alarm
When the drone is going to fly out of the max remote
control distance, the transmitter will beep Didi..didi..
didi... to warn the user to fly back immediately. Or the
drone may lose control and fly away.
Spare Parts Installation Instructions
Propeller Installation and disassembly Diagram
When disassembling, pull up the propeller in the vertical
direction (Picture 11) and remove as Picture 12.
Notice: Because the propeller is blowing up structure, it should keep a bit gap
between the motor housing and the propeller( Picture 13).
About 0.5 mm
Picture 13
Picture 2
Picture 11
Vérications à faire avant le vol
Assurez-vous que la batterie du drone et la batterie de
la télécommande sont bien chargées.
Assurez-vous que le levier gauche de l’émetteur est en
position médiane.
Suivez strictement les instructions fournies pour
allumer et éteindre. Allumez d’abord la télécommande,
puis allumez le drone; Éteignez d’abord le drone,
puis éteignez la télécommande lorsque vous avez
fini d’utiliser le drone. Un démarrage et une mise
hors tension incorrects peuvent vous faire perdre
le contrôle du drone et menacer la sécurité des
personnes. Assurez-vous que vous allumez et éteignez
correctement le drone.
Assurez-vous que la connexion est bien établie entre la
batterie et le moteur, etc. Toute vibration peut causer
une mauvaise connexion et faire perdre le contrôle du
drone.
Une mauvaise utilisation peut provoquer un crash du
drone, ce qui peut entraîner des défauts sur le moteur
et du bruit, puis affecter le vol du drone ou même faire
qu’il ne vole plus.
Termékspecifikációk
| Márka: | Archos |
| Kategória: | drón |
| Modell: | PicoDrone |
Szüksége van segítségre?
Ha segítségre van szüksége Archos PicoDrone, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók drón Archos
3 Augusztus 2024
19 Július 2024
Útmutatók drón
- drón Carrera
- drón Xiaomi
- drón Prixton
- drón Reely
- drón Hama
- drón GPX
- drón Parrot
- drón Carson
- drón Dahua Technology
- drón Denver
- drón DJI
- drón Autel
- drón Revell
- drón Syma
- drón Overmax
- drón SkyRC
- drón Kogan
- drón Amewi
- drón Manta
- drón Blaupunkt
- drón Hubsan
- drón Insta360
- drón SereneLife
- drón Joby
- drón Hobbywing
- drón Swann
- drón DF-Models
- drón Emax
- drón AEE
- drón Brigmton
- drón Maginon
- drón Steren
- drón Graupner
- drón Makeblock
- drón Blade
- drón Ninco
- drón FIMI
- drón Vizu
- drón WowWee
- drón Yuneec
- drón Kaiser Baas
- drón Robbe
- drón Odyssey
- drón Pgytech
- drón XTIM
- drón Jamara
- drón LUXWALLET
- drón WLtoys
- drón Dromida
- drón Quadrone
- drón UGo
- drón Zero-X
- drón Estes
- drón Air Wars
- drón Zero Zero Robotics
- drón CHASING
- drón EHang
- drón Ryze
- drón SwellPro
- drón 3DR
- drón Extreme Fliers
- drón Snaptain
- drón Hobby Zone
- drón PowerVision
- drón Holy Stone
- drón Sky Rider
- drón SkyRider
Legújabb útmutatók drón
1 Április 2025
12 Január 2025
8 Január 2025
8 Január 2025
8 Január 2025
8 Január 2025
8 Január 2025
5 Január 2025
3 Január 2025
3 Január 2025