Használati útmutató American International SBK926

Olvassa el alább 📖 a magyar nyelvű használati útmutatót American International SBK926 (4 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/4
SBK926 Mounting Kit
Subaru
2009-13 FORESTER
2008-11 IMPREZA
2008-14 IMPREZA WRX
VEHICLE APPLICATIONS
©2017 AMERICAN INTERNATIONAL INDUSTRIES, INC. TECH Ver. 03/17 PRINT Ver. 3/17
1. Open the Passenger door and remove the end cover exposing the (1) Phillips screw
securing the right end of the Vent/Trim panel to the right end side of the dash.
2. Remove the (1) Phillips screw securing the right end of the Vent/Trim panel to the
side of the dash, and carefully starting with the Vent end, pry the trim panel forward
working toward the radio. It is not necessary to remove the trim completely, just
unclip to the left side of the radio and rest out of the way.
3. Carefully unclip and remove the Vent/radio trim bezel.
4. Remove the (4) Phillips screws securing the radio to the sub-dash, pull the radio
forward, disconnect all attached harnesses and antenna lead and remove radio.
DASH DISASSEMBLY
1
KIT ASSEMBLY INSTRUCTIONS
1. Insert left and right mounting brackets to rear of kit as shown in Figure A
and secure to rear of kit fascia using (4) small phillips screws included in kit.
2. Insert pocket into lower section of the brackets and snap into rear pocket
support tabs.
3. Insert ISO mountable radio between ISO mount brackets and loosely
attach to sides of radio using screws provided with radio when possible
or screws supplied with kit.
4. Slide radio forward or backward for desired look and tighten screws.
Single ISO Mount Applications
Fig A THERE IS A
SPACE IN BOTH
LEFT AND RIGHT
UPPER BRACKET
TABS FOR
SCREWDRIVER
TO PASS
THROUGH.
2
Double DIN Mount Applications
Fig B
1. Insert IMB-926 L&R into rear of kit & attach using 4 screws supplied w/kit
(See Fig B for bracket tab removal).
2. Insert ISO mountable radio between ISO mount brackets and loosely attach
to sides of radio using screws provided with radio when possible or hardware
included with kit.
3. Slide radio component forward or backward for desired look and tighten screws.
4. Attach a rear support bracket to the rear of the new radio and adjust as necessary
to support the weight of the radio.
THERE IS A
SPACE IN BOTH
LEFT AND RIGHT
UPPER BRACKET
TABS FOR
SCREWDRIVER
TO PASS
THROUGH.
REMOVE SHADED MOUNTING
TABS ON BOTH LEFT AND
RIGHT SIDES OF KIT

Termékspecifikációk

Márka: American International
Kategória: nincs kategorizálva
Modell: SBK926

Szüksége van segítségre?

Ha segítségre van szüksége American International SBK926, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva American International

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025