Használati útmutató American International FM-K574

Olvassa el alább 📖 a magyar nyelvű használati útmutatót American International FM-K574 (7 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/7
©2005 AMERICAN INTERNATIONAL INDUSTRIES, INC. Ver. 3/05
FM-K574 Mounting Kit
Ford
1996-99 TAURUS
Mercury
1996-99 SABLE
VEHICLE APPLICATIONS
1996-1999 Ford Taurus
1996-1999 Mercury Sable
FACTORY RADIO REMOVAL
1. Engage the cars emergency brake.
2. With the key out of the ignition, turn all climate control knobs to a straight up and
down position.
3. You will need a pair of Ford Radio Removal Keys (part # URT-460) to remove the
factory radio/climate control assembly.
4. Insert the Radio removal keys into the holes on the face of the radio/climate control
panel until they click into place. Firmly grip the keys while pressing the keys gently
outward to depress the metal retaining clips attached to the sides of the radio/climate
control assembly. Pull the entire radio/climate control assembly forward to access the
wiring and rear mounted climate controls.
5. Sub-dash modification may be necessary on vehicles with center consoles.
See Figure A.
KIT OVERVIEW
This installation kit is designed to replace the original integrated factory radio/ with
rotary climate control assembly, while utilizing and maintaining the factory rotary climate
controls to this kit.
The FM-K574 kit allows for a single DIN or single ISO mount radio to be installed while
keeping the factory cosmetics and climate control functions intact. The Factory radio/
climate control panel itself is only a slave unit. The amplifier/tuner module is located
in the trunk on the left side under the trunk liner, or for wagons behind the spare tire
on the left side.
Close-up of dash shaded area
(might need to be modified).
Dash radio
opening (front view)
Fig. A
2
FACTORY CLIMATE CONTROL REMOVAL INSTRUCTIONS
Read these instructions thoroughly prior to the removal of the factory climate controls.
1. Carefully remove the three climate control knobs from the face of the radio/climate
control panel by pulling outward.
2. Remove the single screw securing the temperature switch to the rear of the factory
radio/climate control panel then twist the switch clockwise to remove.
3. Remove the single screw securing the fan switch to the rear of the factory
radio/climate control panel then twist the fan switch counter-clockwise to remove.
4. Remove the (3) Torx screws from the rear of the climate control assembly.
5. Carefully un-do the thin strip of tape at the bottom edge of the rear of the climate
control assembly (do not remove entirely) this tape will be re-set later.
6. Carefully separate the bottom of the control assembly panel about a quarter of
an inch.
7. Using a small flat blade screwdriver, unfasten the flow direction switch’s clips from
the rear of the panel and remove flow direction switch.
8. Remove the individual T-15 Torx screw from each side of the factory radio/climate
control securing the metal mounting brackets to the factory assembly. See Figure B.
9. Using a small flat blade screwdriver, pry the metal clips upward to release and remove.
10.Re-attach the factory mounting brackets to the rear of the FM-K574 panel the same
way they were attached to the factory assembly. See Figure B.
Fig. B
Attach factory mounting brackets
to each side as shown in Fig. B
3

Termékspecifikációk

Márka: American International
Kategória: nincs kategorizálva
Modell: FM-K574

Szüksége van segítségre?

Ha segítségre van szüksége American International FM-K574, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva American International

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025