Használati útmutató Alto TS115W

Alto nincs kategorizálva TS115W

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Alto TS115W (20 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/20
QUICKSTART GUIDE
ENGLISH
GUÍA DE INICIO RÁPIDO
ESPAÑOL
GUIDE D'UTILISATION RAPIDE
FRANÇAIS
GUIDA RAPIDA
ITALIANO
SCHNELLSTART-ANLEITUNG
DEUTSCH
SNELSTARTGIDS
NEDERLANDS
2
www.a ltoprofess ional.com/wireles swww.a ltoprofess ional.com/wireles s
BOX CONTENTS
• Truesonic Wireless speaker
• Power cable
• Quickstart Guide
• Safety Instructions & Warranty Information Booklet
INSTALLATION
This speaker should be installed on a stand on the
floor, according to its maximum weight, or suspended
from its suspension points (M10 x 1.5PH, 30mm
length) (see example image). We do NOT recommend
suspending multiple speakers in a vertical array.
CONNECTION DIAGRAM
*Note: Microphones, mixer, and cables are not included. Second Truesonic Wireless
speaker sold separately.
Mixer*
Power
Power
Microphones*
Speaker Speaker*
This diagram is a suggestion for setting up the speaker with audio connections. To pair
the speaker with a Bluetooth™ device, see the BLUETOOTH PAIRING & LINKING
section below.
Eyebolt
Dust cover
Suspension
point
Example:
3
BLUETOOTH PAIRING & LINKING
IMPORTANT:
• These steps are for wireless audio streaming only.
• When pairing or linking, do only one process at a time. Starting one process before the other is finished
will cancel the first.
• The tone sequences for pairing and linking are different, so you can easily distinguish between the two.
ABOUT RANGE
Truesonic wireless loudspeakers use an advanced, extended-range Bluetooth antenna design, allowing for
ranges far greater than traditional Bluetooth devices. The typical range is 60-80 feet (18-24 meters) with a
clear line of sight. However, the range may vary depending on your source device and the environment.
To maximize the range:
• Set your source device on a flat surface and make sure there are no obstacles between the
loudspeaker and your device (e.g., walls, furniture, etc.).
• Turn off your source device’s Wi-Fi.
• Turn off any unneeded 2.4 GHz devices in the nearby vicinity (e.g., other Bluetooth devices, baby
monitors, Wi-Fi access points, microwave ovens, etc.).
• Try using a different Bluetooth source device. Bluetooth signal strength varies between different
devices.
PAIRING
To pair the speaker to your Bluetooth device:
1. Do this on one loudspeaker only: With the loudspeaker powered on, press and release its PAIR
BUTTON. Its LED will flash, and you will hear a tone sequence from the loudspeaker. (If you are using
two Truesonic wireless loudspeakers, this one will be the "master." Also see the LINKING section
below.)
2. From your Bluetooth device’s settings page, enable
Bluetooth and select ALTO PRO WIRELESS
TS115W as the device. When paired successfully,
you will hear a final "confirmation tone" from the
loudspeaker and the PAIR BUTTON LED will light
continuously. (This process may take up to 60
seconds.)
Note: If your device prompts you to select the con reo speakers,” “advanced nection type, select “ste
audio,” or a similar option.
3. Turn the loudspeaker's BLUETOOTH VOLUME knob to its lowest setting.
4. On your Bluetooth device, play music. We recommend setting the playback volume at its maximum
setting. Then, adjust the loudpeaker’s BLUETOOTH VOLUME knob to the desired level.
5. Once your device is paired to the speaker, the speaker will remember the device even after power-
cycling it. To reconnect it, go to your device’s Bluetooth settings page and select “Connect” to re-
establish the connection.
LINKING
If you are using two Truesonic wireless speakers:
1. Make sure no audio is playing from your Bluetooth
device. If it is, pause/stop playback and wait 5
seconds.
2. Press and release the STEREO LINK BUTTON on
each speaker.
3. Both loudspeakers’ LEDs will flash while
"searching" for each other, and you will hear a tone
sequence from both loudspeakers. (This process may take up to 60 seconds. However, the very first
time you link the loudspeakers, the process may take up to 3 minutes.)
4. When they are successfully linked, you will hear a final "confirmation tone" from both loudspeakers and
the STEREO LINK BUTTON LEDs on both loudspeakers will light continuously.
Note: The stereo signal will be split between the two loudspeakers: the master loudspeaker will play the left
channel; the slave loudspeaker will play the right channel.
Tip: When using two loudspeakers, we recommend labeling the master loudspeaker so you can distinguish
between the two in future setups.
Bluetooth is a registered trademark of Bluetooth SIG.
Note: If your device prompts you to enter
a PIN code to pair it to the speaker, enter
0000 (four zeros).
Note: The loudspeaker that is connected
to your source device is the “master”; the
linked loudspeaker is the “slave.” The
source device sends its signal to the
master, and the master relays the signal to
the slave.
4
ADDITIONAL INFORMATION
Truesonic wireless loudspeakers will remember their pairing
and linking settings even after they are powered off. When
you turn the loudspeakers back on, they will automatically
reconnect to each other. When the connections are re-
established between the loudspeakers, the LEDs next to the
STEREO LINK BUTTONS will light continuously.
If the connection is lost between the loudspeakers, or
between the loudspeaker and the source device, and if they do not reconnect automatically, then power-cycle both
loudspeakers and allow them to reconnect.
When the two loudspeakers are linked, you can only pair your source device to the master loudspeaker. The slave
loudspeaker’s PAIR BUTTON will be disabled; if you press it, you will hear 3 rapid “beeps” to indicate that the button
is “locked out.”
To erase all previous pairing and linking settings, press and hold either the PAIR BUTTON or the STEREO LINK
BUTTON for 3 seconds. You will hear a long tone to confirm its pairing and linking settings have been erased. The
LEDs will also turn off. Do this on both the master and the slave loudspeakers. Now, you can pair to a new source
device or link the loudspeakers again.
Note: The volume of the pairing and linking tones are pre-set to an optimal level. To adjust their volume, see the
REAR PANEL OVERVIEW section for information.
REAR PANEL OVERVIEW
1. POWER INPUT – Connect the included power cable to this
input and connect the other end of the cable to a power
source. Make sure the loudspeaker's POWER SWITCH is
set to "off" when plugging and unplugging the cable.
2. POWER SWITCH – Turns the loudspeaker on/off. Make
sure the VOLUME knob is set to "zero" before turning it on.
3. POWER LED – Illuminates when the loudspeaker is on.
4. PAIR BUTTON – Press and release this button to pair the
loudspeaker to your Bluetooth device. See the
BLUETOOTH PAIRING & LINKING section for pairing
instructions.
5. BLUETOOTH VOLUME – Turn this knob to adjust the input
volume of your paired Bluetooth device.
6. STEREO LINK BUTTON – When using a pair of Truesonic
Wireless loudspeakers, press and release this button on
each speaker to "link" them for wireless stereo audio. See
the BLUETOOTH PAIRING & LINKING section for more
information.
7. INPUT – Use a standard 1/4" TRS or XLR cable (not
included) to connect your sound source to this input.
8. INPUT VOLUME – Turn this knob to adjust the input
volume for each INPUT.
9. SIGNAL LIMIT LED – Illuminates RED when the internal
protection circuit is activated by a high signal level. The
protection circuit dynamically reduces the signal level to
avoid audible distortion and to protect the woofer and high-
frequency driver from over excursion or mechanical damage. If the LED is lit constantly, or the sound is
distorted, reduce the signal level of your sound source, or lower the volume control on the rear panel.
10. MIX OUT – Use a standard XLR cable (not included) to connect this jack to the input of another loudspeaker.
11. MIX OUT SELECTOR – When disengaged (PRE VOL), the MIX OUT level will be unaffected by the INPUT
VOLUME controls. When engaged (POST VOL), the MIX OUT level can be adjusted by the INPUT VOLUME
controls.
Note: The BLUETOOTH VOLUME control always affects the MIX OUT.
12. CONTOUR – Engage (depress) this switch to equalize the mix for optimal music playback. Disengage (raise)
the switch during live performance for a flatter response.
13. GROUND SWITCH – Press this switch to reduce hum or noise.
14. PAIRING/LINKING TONE VOLUME – Below and to the left of the STEREO LINK BUTTON, there is a small
opening that exposes a recessed level control. This potentiometer controls the volume of the pairing/linking
tones. This is pre-set to an optimal volume by default, but you may use a small, flathead jeweler’s screwdriver
to adjust it from -∞ dB to +10 dB. (Turning it clockwise increases the volume; counter-clockwise decreases it.)
To return it to the factory setting, turn it until it you feel the center detent at the 12 o’clock position.
Tip: Once your device is paired to the
loudspeaker, the loudspeaker will remember
the device even after power-cycling it. To
reconnect, go to your device’s Bluetooth
settings page and select “Connect” to re-
establish the connection.
www.alt oprofessional.com/wireless
12
3
4
6
7 7
8 8 9
10
11
12
13
14
5
5
www.a ltoprofess ional.com/wireles swww.a ltoprofess ional.com/wireles s
CONTENIDO DE LA CAJA
• Altavoz inalámbrico Truesonic
• Cable de alimentación
• Guía de inicio rápido
• Folleto de instrucciones de seguridad e información sobre la garantía
INSTALACIÓN
Este altavoz debe instalarse sobre un soporte
colocado en el suelo, de acuerdo a su peso máximo, o
suspendido de sus puntos de suspensión (M10 x
1.5PH, 30 mm de longitud) (vea la imagen de
ejemplo). NO recomendamos suspender varios
altavoces en un arreglo vertical.
DIAGRAMA DE CONEXIÓN
*Nota: No se incluyen micrófonos, mezclador ni cables. El segundo altavoz inalámbrico
Truesonic se vende por separado.
Mezclador*
Alimentación
Alimentación
Micrófonos*
Altavoz Altavoz*
Este diagrama es una sugerencia para la instalación del altavoz con conexiones de
audio. Para aparear el altavoz con un dispositivo Bluetooth, consulte la sección
APAREAMIENTO CON BLUETOOTH Y ENLACE más abajo.
Perno de ojal
Tapón
antipolvo
Punto de
suspensión
Ejemplo:

Termékspecifikációk

Márka: Alto
Kategória: nincs kategorizálva
Modell: TS115W

Szüksége van segítségre?

Ha segítségre van szüksége Alto TS115W, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók nincs kategorizálva Alto

Alto

Alto TS115W Útmutató

10 Augusztus 2024
Alto

Alto Presenter PA Útmutató

29 Július 2024
Alto

Alto STEALTH 1 Útmutató

16 Július 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
Soundstream

Soundstream VRN-64HBL Útmutató

10 Április 2025
Panasonic

Panasonic Lumix DMW-AC11 Útmutató

10 Április 2025
Planet

Planet PWR-240-48 Útmutató

9 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
Alpine

Alpine DP2-40C-BC Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025