Használati útmutató AFX Callie CALP05WHLNR3

AFX Lampa Callie CALP05WHLNR3

Olvassa el alább 📖 a magyar nyelvű használati útmutatót AFX Callie CALP05WHLNR3 (1 oldal) a Lampa kategóriában. Ezt az útmutatót 9 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/1
E26 Bulb door Luminaires In
Ceiling Mount
120VAC / 60Hz
Page 1 of 1 R0 8061463
Part #: CALP05WH 3 LNR
Part #:
Limited Factory Warranty
AFX Inc. hereby warrants that this xture is free from defects in materials and workmanship when installed and used under normal operating conditions
for a period of 5 years from date of purchase. This warranty covers all component parts and extends only to replacement of defective xture or
components; it does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit.
View shown for
reference only.
Individual models
may vary.
Safety Precautions
Read all safety precautions and installation instructions carefully before installing or servicing this xture. Failure to comply with these instructions could result in potentially fatal
electric shock and/or property damage.
is recommended that a qualied electrician perform all wiring. This xture must be wired in accordance with all national and local electrical codes. It
Do not handle any energizedxture or attempt to energize any xture with wet hands or while standing on a wet or damp surface or in water.
This xture is designed for use in a 120 / 60Hz circuit. VAC
Make sure that the power source conforms to the requirements of the xture. (See labels on the xture housing).
To reduce the risk of electrical shock, and to assure proper operation, this xture must be adequately grounded. To accomplish proper grounding, there must be a separate ground
wire (green) contact between this xture and the ground connection of your main power supply panel.
This xture is intended to be used for general indoor lighting in dry or damp locations.
Assembly Instructions
Step 1 Preparing for installation–
A. at fuse or circuit breaker box before installing or servicing Disconnect electrical power
any part of this xture.
B. Carefully remove the xture from the carton, remove components from hardware kit.
C. Install the channel (1) to the junction box (not included) using two screws (2) to secure it.
D. Mark the locations of the four extra mounting holes on the ceiling. Take the channel (1)
down and punch a small hole into the ceiling at each location using a nail or an awl to see
if there is a wood joist. If there is a joist, use suitable wood screws (7) to mount the
channel (1). Where there is no joist to screw into, use a wall anchor (6) to mount pan
securely to the ceiling.
Step 2 Installing pendants –
A. Install pendant to the cover plate (3) by pulling cord through the canopy strain relief (4).
Tighten the strain relief screw when the cord is at the desired height. Repeat for each
pendant.
Note: Each co rd is 108” long.
B. Once all pendants are their desired height, group all of the black pendant wires at
together along with an extra ying single black lead wire. This single lead will be used to
connect to the power source in Step 3. Secure with wire nut (provided).
C. Repeat Step 2B for all white pendant wires.
Wiring All wiring must take place inside junction box (not included) –
Caution: Make sure power is o at fuse or circuit breaker box. Check power wires for
damage or scrapes. Use wire suitable for at least 90°C (194°F). Most dwellings Note:
built before 1985 have supply wire rated to 60°C. Consult a qualied electrician to ensure
correct branch circuit conductor before installing.
Step 3 Wiring xture –
A. Make all wire connections to appropriate wire. Secure with wire nuts (provided).
B. Connect the green wire from the xture to the supply source ground wire.
C. Connect the black wire from the pendants to the black (L) wire from supply power source.
D. Connect the white wire from the pendants to the white (N) wire from supply power source.
E. Pull on each wire lead to make sure connections are secure. Make Do not mix wires.
certain no bare wires are exposed outside of wire connectors. Tuck all connections neatly
into the junction box.
Step 4 Installing cover pla –te
A. Align the mounting holes on the xture plate with the two screws on the xture channel (1)
and use two nials (5) to secure it.
Step 5 Installing diusers –
A. Slide glass diuser (9) over the socket assembly (8) and use the fastener 0 to secure (1 )
the diuser in place. Note: Do not over tighten as it may cause chipping of the glass.
Step 6 Lamping –
A. Install medium base bulb (E26, 60W max not included) into each socket and turn clockwise until –
secured.
Step 7 Restore power at fuse or circuit breaker box –

Termékspecifikációk

Márka: AFX
Kategória: Lampa
Modell: Callie CALP05WHLNR3

Szüksége van segítségre?

Ha segítségre van szüksége AFX Callie CALP05WHLNR3, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Lampa AFX

AFX

AFX Mae MAEP20MBSNLW Útmutató

3 Január 2025
AFX

AFX Callie CALP05WHLNR3 Útmutató

13 Október 2024
AFX

AFX Boon BONP2032L30D1BK Útmutató

13 Október 2024
AFX

AFX Callie CALP99WHRND4 Útmutató

13 Október 2024
AFX

AFX Evanston EVNP2532LAJUDSN Útmutató

13 Október 2024

Útmutatók Lampa

Legújabb útmutatók Lampa

Theben

Theben theLeda B10L Útmutató

8 Április 2025
Theben

Theben theLeda P24L Útmutató

8 Április 2025
NUVO

NUVO Arabel 60/6967 Útmutató

5 Április 2025
NUVO

NUVO Gotham 60/191 Útmutató

5 Április 2025
NUVO

NUVO Cordello 60/7884 Útmutató

5 Április 2025
NUVO

NUVO Clarksville 60/8061 Útmutató

5 Április 2025
NUVO

NUVO Gotham 60/190 Útmutató

5 Április 2025
V-TAC

V-TAC VT-407 Útmutató

5 Április 2025
V-TAC

V-TAC VT-415 Útmutató

5 Április 2025
Cateye

Cateye Nano60 TL-LD830 Útmutató

5 Április 2025