Használati útmutató Aeotec Range Extender 7

Aeotec okos otthon Range Extender 7

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Aeotec Range Extender 7 (9 oldal) a okos otthon kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/9
11-6-2020 Range Extender 7 user guide. : Aeotec Group
https://aeotec.freshdesk.com/support/solutions/articles/6000226827-range-extender-7-user-guide- 1/4
Range Extender 7 user guide.
Modified on: Mon, 16 Mar, 2020 at 2:06 AM
Aeotec Range Extender 7.
Aeotec Range Extender 7 was developed to amplify Z-Wave signals. It isZ-Wave Plus (http://aeotec.com/z-wave-plus)
powered by Aeotec’s technology. You can find outGen7 (https://aeotec.com/z-wave-home-automation/z-wave-gen7.html)
more about 7 by following that link.Range Extender (http://aeotec.com/z-wave-repeater)
To see whether Range Extender 7 is known to be compatible with your Z-Wave system or not, please reference our Z-
Wave gateway comparison (http://aeotec.com/z-wave-gateways) listing. The technical specifications of Range
Extender 7 (https://aeotec.freshdesk.com/a/solutions/articles/6000226828) can be viewed at that link.
Important safety information.
Please read this and other device guides carefully. Failure to follow the recommendations set forth by Aeotec Limited
may be dangerous or cause a violation of the law. The manufacturer, importer, distributor, and/or reseller will not be
held responsible for any loss or damage resulting from not following any instructions in this guide or in other materials.
Keep product away from open flames and extreme heat. Avoid direct sunlight or heat exposure.
Range Extender 7 is intended for indoor use in dry locations only. Do not use in damp, moist, and/or wet locations.
11-6-2020 Range Extender 7 user guide. : Aeotec Group
https://aeotec.freshdesk.com/support/solutions/articles/6000226827-range-extender-7-user-guide- 2/4
Quick start.
Adding your Range Extender into a Z-Wave network.
Getting your Range Extender up and running is as simple as plugging it into a wall outlet and adding it to your Z-Wave
network. There are 2 methods to pairing your Range Extender depending on the capabilities of your Z-Wave
gateway/controller/hub.
SmartStart Inclusion.
You can use this method of inclusion only if your Z-Wave gateway/controller/hub supports SmartStart.
1. Open up your Z-Wave gateway/controller/app.
2. Select SmartStart inclusion.
3. Scan the QR code located on the Range Extender 7.
4. Within 10 minutes after powering your Range Extender 7, it will automatically get included into your Z-Wave
gateway/controller/hub.
LED will flash for 1 second after Repeater is powered, if successful, the LED will become a solid bright light for 2
seconds.
Classic Inclusion.
1. Decide on where you want your Range Extender to be placed and then plug it into a wall outlet.
Make sure that the LED is breathing its white LED.
2. Set your Z-Wave Controller into pairing mode.
3. Press the Z-Wave Button on your Range Extender and quickly release the button (should only be a quick tap
action on the button).
Range Extender 7 will quickly flash its white LED up to 30 seconds or until it is paired successfully. If successfully
paired, the LEDs light will become brighter.
If your repeater failed to pair, the LED will return to slow breathing LED. If it is this case, please return to step 2.
11-6-2020 Range Extender 7 user guide. : Aeotec Group
https://aeotec.freshdesk.com/support/solutions/articles/6000226827-range-extender-7-user-guide- 3/4
4. If you pairing with S2 encryption/security, enter the first 5 digits of the DSK into your controller/gateway/hub
interface when requested.
The DSK is printed on the Range Extender 7 itself located right under the QR code.
General LED Status
There are a few LED indications that you will need to pay attention to for the Range Extender 7.
Unpaired from network.
Slow breathing white LED
While paired to an existing network.
The LED state is configurable, there are 2 states that you can choose, the LED will remain in a solid state as off or
on:
LED on.
LED off.
Advanced Functions.
Removing your Range Extender from a Z-Wave network.
Your Range Extender can be removed from your Z-Wave network at any time. You’ll need to use your Z-Wave
network’s main controller. To set your Z-Wave controller/gateway into removal mode, please refer to the respective
section within your controller instruction manual.
1. Set your Z-Wave Controller into device removal mode.
2. Press the Z-Wave Button on your Range Extender.
3. If Range Extender has been successfully removed from your network, its LED will return to a slow breathing
light.
Control LED of Range Extender 7.
You can turn the LED on or off by using the action button of your Range Extender 7:
Tap the Action Button 2x times.
LED should turn on or off each time you do so.

Termékspecifikációk

Márka: Aeotec
Kategória: okos otthon
Modell: Range Extender 7

Szüksége van segítségre?

Ha segítségre van szüksége Aeotec Range Extender 7, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók okos otthon Aeotec

Aeotec

Aeotec Smart Home Hub Útmutató

16 Augusztus 2024
Aeotec

Aeotec Range Extender 7 Útmutató

13 Augusztus 2024
Aeotec

Aeotec SmartThings Hub V3 Útmutató

13 Augusztus 2024

Útmutatók okos otthon

Legújabb útmutatók okos otthon

Busch-Jaeger

Busch-Jaeger 6151-0-0217 Útmutató

29 Március 2025
Busch-Jaeger

Busch-Jaeger 6151-0-0218 Útmutató

29 Március 2025
Tesla

Tesla MS360 Útmutató

29 Március 2025
Shelly

Shelly BLU Button 1 Útmutató

27 Március 2025
Sommer

Sommer SOMweb Útmutató

19 Március 2025
EZVIZ

EZVIZ T33 Útmutató

18 Március 2025
Niko

Niko 350-20071 Útmutató

15 Január 2025
WiZ

WiZ Smart Útmutató

14 Január 2025
EZVIZ

EZVIZ DL03 Útmutató

14 Január 2025
EZVIZ

EZVIZ DL04 Pro Útmutató

14 Január 2025