Használati útmutató Adastra RM4460

Adastra Vevő RM4460

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Adastra RM4460 (6 oldal) a Vevő kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/6
RM4460
4-INPUT, 4-ZONE MIXER- PLIFIER 4 x 60W AM
Item ref: 953.446UK
User Manual
Version 0 1.
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
953.446 User Manual UK
Introduction
Thank you for choosing an Adastra 4-zone mixer-amp as part of your sound system. RM4460
This mixer with 4 separate 100V amplifiers has the advantage of a 4 in / 4 out matrix with inbuilt media player.
Please read this manual to gain the best results from your product and avoid damage through misuse.
SAFETY SYMBOL AND MESSAGE CONVENTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this
unit
This symbol indicates that there are important operating and maintenance instructions in the
literature accompanying this unit.
SAFETY NOTICE
1. Prior to use, read through this manual
2. Keep the manual in good condition
3. Pay attention to safety warnings
4. Observe all operating requirements
5. Do not use the device near water or wet areas
6. For cleaning, only use a lint-free, dry cloth
7. Install according to the specifications
8. Place away from heat sources or heating appliances
9. Use mains lead provided and avoid damage to cable or connectors
10. Unplug power from mains during stormy weather or if unused for long periods
11. In case of malfunction, water ingress or other damage, consult qualified service personnel
12. Do not place in damp areas or near liquids or moisture. Do not spill liquids on the housing
13. Please pay attention to warning symbols during transit and placement
14. Terminals marked with the symbol are HAZARDOUS LIVE and should only be connected by qualified personnel
15. Ensure that the apparatus is connected to a mains socket with a protective EARTH connection
16. Ensure correct operation of the mains switch
Warning
To prevent the risk of fire or electric shock, do not expose any components to rain or moisture.
If liquids are spilled on the casing, stop using immediately, allow unit to dry out and have checked by qualified personnel before
further use.
Avoid impact, extreme pressure or heavy vibration to the case
No user serviceable parts inside Do not open the case refer all servicing to qualified service personnel. – –
Safety
• Check for correct mains voltage and condition of IEC lead before connecting to power outlet
Placement
• This unit can be used free-standing or fixed into a 19” rack
• Ensure adequate support and access to controls and connectors when rack-mounting
Cleaning
• Use a soft cloth with a neutral detergent to clean the housing as required
• Do not use strong solvents for cleaning the unit
953.446 User Manual UK
Front panel
Rear panel
Setting up
The may be operated free-standing or mounted into a 19 rack. Ensure adequat ventilation and access to connectors and RM4460 ”e
controls. Start with all LEVEL controls turned lly down and BASS/TREBLE EQ controls set mid- y (12 o clock), then proceed to fu wa ’
connect all required input sources.
I the optional CS4 call station is being used, connect this via the RJ45 connector on the rear panel (36) f
Input 1 accepts a paging microphone on balanced XLR (34) and a VOX feature may be ed to give this priority over other channels. us
To enable VOX, set the VOX DIP switch to ON (33), which will cause other channels to mute when the microphone is spoken into.
Next to the VOX DIP switch is a PHANTOM DIP switch (34) which activates phantom power to the R connector for condenser mics. XL
Inputs 2 and 3 can accept a microphone or line input o a combo connector, which accepts either 6.3mm jack or XLR (30, 32) n
A DIP switch (29, 31) gives the option of selecting mic or line level sensitivity for the input.
An adjacent DIP switch can enable phantom power to the XLR contacts of the combo connector to power a condenser microphone.
The LINE input can be connected via a pair of RCA connectors (27) or a 3-screw terminal connector.
Th screw terminal ock is removable for easy connection and has terminals for +/- (28) e bl /G
Connect the hot signal to + cold signal to and ground to G for a balanced input signal. “ ” “ ”, “ ” “–” “ ”
Unbalanced signals only use 2 wires, so connect the signal (core) + and connect the ground (braid) to - and G together. to “ ” “ ”
A separate 3.5mm line input on the front panel can be fed through the media player for an mp3 player or smart pho . ne
Line level outputs from each zone may be connected from RCA connectors (26) for sending further amplifiers if required. to
1.
AUX 3.5mm jack input
11.
Input 2 EQ controls
2.
USB port (for pen drive only)
12.
Input 2 level control & signal LED
3.
Media player controls
13.
Input 2 zone output selectors
4.
Media player display
14.
Input 3 EQ controls
5.
Media/Line input selector
15.
Input 3 level control & signal LED
6.
Media/Line level control & signal LED
16.
Input 3 zone output selectors
7.
Media/Line zone output selectors
17.
Zone level & signal/clip & mute/call LEDs 1
8.
Input 1 p ing mic EQ controls ag
18.
Zone 2 level & signal/clip & mute/call LEDs
9.
Input 1 p ing mic level control & signal LED ag
19.
Zone 3 level & signal/clip & mute/call LEDs
10.
Input 1 p ing mic zone output selectors ag
20.
Zone 4 level & signal/clip & mute/call LEDs
21.
Power on/off switch & LED
22.
IEC mains inlet & fuse holder
31.
Input 2 Phantom/Mic/Line DIP switches
23.
Cooling fan vent (do not cover)
32.
Input 2 combo jack/XLR connector
24.
Low impedance (4 speaker tput terminals Ω) ou
33.
Input 1 Phantom/Mic/Line DIP switches
25.
100V speaker tput terminals ou
34.
Input 1 combo jack/XLR connector
26.
Individual zone line level signal outputs (RCA)
35.
Call station level control (for optional CS4)
27.
Line input (2 x RCA)
36.
Call statio RJ45 input (for optional CS4) n
28.
Line input ( - round screw termina ) +/ /G ls
37.
24V emergency mut screw terminals e
29.
Input 3 Phantom/Mic/Line DIP switches
38.
Bluetooth antenna connection (SMA)
30.
Input 3 combo jack/XLR connector
39.
FM radio aerial F-connector

Termékspecifikációk

Márka: Adastra
Kategória: Vevő
Modell: RM4460

Szüksége van segítségre?

Ha segítségre van szüksége Adastra RM4460, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Vevő Adastra

Adastra

Adastra V-122 Útmutató

29 Augusztus 2024
Adastra

Adastra RS240 Útmutató

16 Augusztus 2024
Adastra

Adastra UM30 Útmutató

14 Augusztus 2024
Adastra

Adastra RS120 Útmutató

12 Augusztus 2024
Adastra

Adastra DM60 Útmutató

9 Augusztus 2024
Adastra

Adastra UA60 Útmutató

9 Augusztus 2024
Adastra

Adastra UM90 Útmutató

9 Augusztus 2024
Adastra

Adastra RMC120 Útmutató

9 Augusztus 2024
Adastra

Adastra IW60B Útmutató

9 Augusztus 2024
Adastra

Adastra RM60 Útmutató

8 Augusztus 2024

Útmutatók Vevő

Legújabb útmutatók Vevő

Yamaha

Yamaha Aventage RX-A4A Útmutató

9 Április 2025
Yamaha

Yamaha Aventage RX-A8A Útmutató

9 Április 2025
DJI

DJI D-RTK 3 Útmutató

5 Április 2025
Phonocar

Phonocar PH544 Útmutató

5 Április 2025
QSC

QSC SPA-Qf 60x2 Útmutató

2 Április 2025
Harper

Harper HDT2-5010 Útmutató

2 Április 2025
Harper

Harper HDT2-2010 Útmutató

2 Április 2025
Alpine

Alpine MRX-F65 Útmutató

31 Március 2025
Streacom

Streacom TL1 Útmutató

31 Március 2025
Pro-Ject

Pro-Ject Stereo Box DS Útmutató

30 Március 2025