Használati útmutató Walrus Audio Phoenix

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Walrus Audio Phoenix (1 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/1
The Walrus Audio Phoenix is a 15-Output isolated power supply,
utilizing two internal custom wound toroidal transformers to provide
a high level of noise rejection, giving artists the purest sound in their
signal chain. The Phoenix is housed in a solid die cast enclosure
and is 9.75” long x 2.6” wide x 2” high and has the following outputs
available:
8 - 9V 100mA • 4 - 9V 300mA • 1 - 18V/9V 100mA • 2 - 12V/9V 100mA
The Phoenix comes with a detachable 230V AC power cord. This unit
comes with 15, 2.1mm barrel black power cables and 2 black-to-red
(line 6) power cables.
POWER LED
Illuminated when the
supply is on.
FRONT
PHOENIX
clean power supply
230v
VOLTAGE RATING
The voltage rating for your pedal must be 9VDC (direct current), do not use the
Phoenix for AC (alternating current pedals). Most effects pedals are designed
for 9VDC power, however, you should always check rst or you could risk
destroying your pedal.
POLARITY
For all standard effects pedals with center negative 2.1mm barrels, you can
use the Black-to-Black barrel connectors. Specically, for Line 6 pedals,
you will have to use the Black-to-Red connectors. If you have a question
about the voltage requirement of your pedal or which output to use, email
customerservice@walrusaudio.com.
CURRENT DRAW
If the current requirement for your pedal is between 100mA - 300mA, you will
need to use the 300mA outputs. For anything less than 100mA, you can use
the 100mA outputs. Note: using the high current output on a low current draw
pedal will work ne and not hurt the pedal. Refer to your pedals manual for its
specic requirements.
WARRANTY
The Phoenix comes with a limited lifetime warranty for workmanship and
components. Warranty does not include misuse or accidents resulting in
damage. Warranty is not transferable or assignable and will only be issued
to the original owner. Valid with receipt showing date of purchase. Contact
repairs@walrusaudio.com to receive an RMA number before returning product.
WARNING
Before connecting your effects pedal to the Phoenix, you must rst verify the
power requirements for your pedal. Input Voltage Requirements - 120V (60Hz).
This product will be destroyed if any other input voltage is used, voiding the
warranty. If the backplate is opened, the warranty is immediately voided. For
repairs, troubleshooting or questions, contact us at repairs@walrusaudio.com.
Do not attempt to x defective unit yourself. Contact Walrus Audio at repairs@
walrusaudio.com for help.
Flip switch up for 18V, down for 9V.
Flip switch up for 12V,
down for 9V.
Standard 2.1mm
9VDC plug for
most effects pedals
Standard 2.1mm
9VDC Jack
Negative-to-Ground
AUS UK JAP UK
230VAC INPUT
Plug male end of included power cord into
a 230VAC power source. Once plugged in,
the LED light will come on indicating that
the power supply is now on.
BACK

Termékspecifikációk

Márka: Walrus Audio
Kategória: nincs kategorizálva
Modell: Phoenix

Szüksége van segítségre?

Ha segítségre van szüksége Walrus Audio Phoenix, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva Walrus Audio

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva