Használati útmutató Vitek VTC-C960WS

Vitek nincs kategorizálva VTC-C960WS

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Vitek VTC-C960WS (32 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/32
VITEK
VTC-C960DS
VTC-C960WS
750 TVL 960H True Day/Night CCD
Cameras w/Effio-A/V Processing
• VTC-C960DS: 750 TVL 960H True Day/Night CCD Camera
w/Effio-A Processing
• VTC-C960WS: 750 TVL 960H WDR Day/Night CCD
Camera w/Effio-V Processing
• 1/3” High density Sony CCD (960H)
• High Resolution of 750 Horizontal Lines
• Small scale design to fit in 5” dome enclosures such as the
Pelco DF5 Housing
• E-WDR by ATR-EX (Adaptive Tone Reproduction) (VTC-
C960DS)
• True WDR (Wide Dynamic Range) (VTC-C960WS)
• Sensitivity of 0.0005 Lux
• XD-DNR (2D+3D DNR) Advanced Digital Noise Reduction
• True Day/Night by ICR - Infrared Cut Removal
• Built-in Motion Detection with a 24x16 Grid
• Privacy Mask function with up to 15 programmable mask
areas
• 12VDC / 24VAC Dual Voltage Operation
• Lenses Sold Separately
2
CAUTION: TO REDUCE THE RISK OF ELECTIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
3
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual appearance of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
Never open the device such as boards.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.
5
Key Features
General Description
• With ICR mechanism,
- Enhances its sensitivity about 10x at night time
- Can accepts the infrared light
• With Effio-V/A series Enhanced digital imaging system,
- Delivers the crystal clear images providing 750TVL resolution in conjunction
with SONY 960H High density CCD.
- is provided ‘TRUE WDR’ functionVTC-C960WS
- is provided ‘D-WDR by ATR-EX’ functionVTC-C960DS
- Color signal processing provides the optimum balance between the luminance
and chroma signals for high color reproducibility even for the detail scene which
contains very high spatial frequency.
- Incorporates 2D+3DNR signal processing.
This is an ultra-clear resolution camera which realizes over 750TVL resolution and
a crisp color reproduction with SONY 960H CCD and Effio-V(Effio-A) Enhanced
image signal processor.
• VTC-C960DS: 750 TVL 960H True Day/Night CCD Camera w/Effio-A Processing
• VTC-C960WS: 750 TVL 960H WDR Day/Night CCD Camera w/Effio-V Processing
• 1/3” High density Sony CCD (960H)
• High Resolution of 750 Horizontal Lines
• Small scale design to fit in 5” dome enclosures such as the Pelco DF5 Housing
• E-WDR by ATR-EX (Adaptive Tone Reproduction) (VTC-C960DS)
• True WDR (Wide Dynamic Range) (VTC-C960WS)
• Sensitivity of 0.0005 Lux
• XD-DNR (2D+3D DNR) Advanced Digital Noise Reduction
• True Day/Night by ICR - Infrared Cut Removal
• Built-in Motion Detection with a 24x16 Grid
• Privacy Mask function with up to 15 programmable mask areas
• 12VDC / 24VAC Dual Voltage Operation
• Lenses Sold Separately
6
Dimensions
L- Wrench:
1.5mm (1pc)
Dust Protection
Cap (1pc)
(unit : mm)
Operating
Instruction
Camera
1.73”
2.09”
1.89”
Ø1.81”
2.38”
2.89”
7
L-Wrench
Dust
Protection Cap
No.
1
2
3
4
DC Iris
Damp(-)
Damp(+)
Drive(+)
GND
Flange Lock screw
Front Case
Rear Case
Back focus
adjusting Flange
Mount Holes
(Top / Bottom)
REAR VIEW
Lens Connector
for Auto Iris lenses
PIN 1PIN 3
PIN 2PIN 4
① Video out connector(BNC)
② Power input terminal
③ OSD Control Joy stick
④ DC Auto Iris Lens connector
①
②
③
④
8
1. Remove the dust protection cap from the lens mount.
2. Screw the lens onto the camera firmly.
3. Plug the lens plug into the lens connector on the rear of camera case.
4. Mount the camera to the wall or ceilling with a corresponding mounting bracket
through the camera mount holes (1/4” thread insert) on its top or bottom.
CAUTION
Installation and commissioning Instructions
• Make sure the power is removed before the installation.
• Follow the order for applying power.
First connect the low voltage (DC12V or AC24V), then plug the AC adapter to AC
outlets to avoid an improper reset from power jitter and a damage from the surge
voltage when no load.
• Care should be taken the cable is NOT to be damaged, kinked or exposed in the
hazardous area.
• Do not expose the camera directly to a strong light source such as the sun or spot
light.
Setting the back focus adjustment
The proper back focus adjustment is essential for the motorized zoom lens to get the
all time sharp focus when zooming in and out by the remote control.
For easier and better adjustment, this camera provides FOCUS ADJUST menu which
prevents from the mistake of the focus adjustment.
With enabling FOCUS ADJUST menu, follow the procedure to get the best back focus
adjustment.
1. Set the lens for the zoom position to WIDE and the focus position to INFINITE(∞).
2. Shoot the object departing from about 10Meters.
3. Adjust ’Back focus adjusting Flange’ until the optimum focus is achieved.
4. Set the lens for zoom position to TELE and adjust the lens focus for best focus.
5. Set the lens for zoom position to WIDE again, check if the focus adjustment was
the best. If not, re-adjust ‘Back focus Flange’ slightly.
6. After the setting, tighten the ‘Flange lock screw’ with L-wrench supplied.
Start up
When the camera is powered properly, it starts up with initializing the internal
parameters.
9
Using OSD Controller
Setup menu can be accessed and controlled by OSD control joy stick on the rear
of the camera unit.
Five commands are available with the joy stick.
The design of rear panel could be different according to the camera models.
Description of the joystick operation
1) SET Key (●) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down.
2) UP/DOWN Key ( ) : Choose the desired sub-menu and to move the▲/▼
cursor up or down.
3) LEFT/RIGHT Key ( : Set up the value of the selected menu. Used to◄/►)
adjust the desired menu selection and to move the cursor left or right.
10
• / : Selects previous page or next page.
• EXIT : Enters ‘EXIT’ menu.
• RETURN : Returns to the previous menu.
OSD menu Startup
OSD menu Table
Press the ‘OSD menu SET key’ down to access the setup menu mode.
SETUP MENU
ADVANCED MENU
CONFIGURATION
SCENE SELECT FULL AUTO/ INDOOR/ OUTDOOR/ BACKLIGHT/ ITS/ CUSTOM
SHUTTER/AGC 100
42DB
OFF
1/50(1/60)
42DB
1/50(1/60)
42DB
127
30
200
INDOOR
10
AE LEVEL
AUTO
AGC MAX
AGC MAX
SENS UP
MANUAL
FIX
ATW
OFF
HLC
WHITE BAL
HLC / BLC
SHUTTER
AGC MAX
SHUTTER
SPEED
DELAY CNT
ATW FRAME
ENVIRONMENT
CLIP LEVEL
SETUP MENU
1 / 2
SCENE SELECT
PICT ADJUST
EZOOM
DIS
PRIVACY MASK
MOTION DET
SYS SETTING
OFF
OFF
OFF
EXIT
FULL AUTO
SETUP MENU
2 / 2
LANGUAGE
VERSION
MAINTENANCE
EXIT
ENGLISH
1.0
11
OFF
INT
3
80
120
AUTO
---
3
DAY/NIGHT
ON/OFF
SET1/2/3
480
290
MID
LEVEL
AUTO
WDR for VTC-C960WS, ATR-EX for VTC-C960DS
PICT ADJUST
EZOOM
DIS
IR OPTIMIZER
LENS SHD COMP
DEFOG
FLK LESS
ANTI CR
BRIGHTNESS
CONTRAST
SHARPNESS
HUE
COLOR GAIN
OFF
ON
OFF / ON
AREA SEL
DISPLAY
POSITION
COLOR
128
32
8
64
128
MAG
PAN
TILT
1/15
OFF
0
512
256
WDR / ATR-EX
DNR
DAY/NIGHT
3
BURST
CNTL SIGNAL
DELAY CNT
DAY->NIGHT
NIGHT->DAY
MODE
IR AREA
LEVEL
IR LED
COLOR NIGHT
PATTERN
POSH
POSV
LEVEL
GAIN CNTL
GAIN CNTL
MODE
MODE
ON
OFF (default)
OFF
ON
OFF
ON
OFF
AUTO
ON
AUTO / OFF / ON
SCENE SELECT
PRIVACY MASK
12
PRIVACY MASK
MOTION DET
SYS SETTING
LANGUAGE
VERSION
MAINTENANCE
EXIT
TRANSP
MOSAIC
111
0
OFF
AREA SEL
AREA MODE
TOP
BOTTOM
LEFT
RIGHT
TYPE
MODE
ADJUST
SPEED
OFF
ON
LENS
CAMERA ID
1.01
W.PIX MASK
CAMERA RESET
SAVE / NOT SAVE / CANCEL / BACK
DETECT SENSE
INTERVAL
BLOCK DISP
MASK AREA
MONITOR AREA
AUTO
FLIP
LCD / CRT
MANUAL COMP
AUTO COMP
DATA CLEAR
LEVEL1 / LEVEL2 / AUTO
YES / NO
1/4
OFF
DC
AUTO
30
REGISTRATION
REG. POINT
CURSOR COLOR
BLINK
REG. NUMBER
OFF / V / H / HV
CRT
English/ Spanish/ Russian/ Portuguese/ German/ French/ Chinese/ Japanese
13
OSD menu Setup
Press the OSD menu SET key down to access the setup menu mode.
Sets the SHUTTER/AGC level to AUTO, MANUAL or FIX.
These options have been pre-configured at the factory for optimal performance.
You can chose one of FULL AUTO, INDOOR, OUTDOOR, BACKLIGHT, ITS and
CUSTOM according to the environments.
Each SCENE preset offers how to set SHUTTER +AGC, WHITE BAL, HLC/BLC,
WDR/ATR-EX2, DNR, DAY/NIGHT, IR OPTIMIZER, LENS SHD COMP, DEFOG,
FLK LESS, and ANTI CR functions to get the best image for the SCENE SELECT.
If the selected preset does not seem to be the best choice, the further adjustments
are available in each preset.
1. SCENE SELECT
1-1. SHUTTER/AGC
Video level is automatically controlled to follow the settings of AE LEVEL, AGC
MAX, SENS UP. In this mode, ‘DC Auto Iris Lens’ and ‘Fixed Lens’ are available.
1-1-1. AUTO:
Video level is manually controlled by the settings of SHUTTER, AGC MAX.
In this mode, ‘DC Auto Iris Lens’ is only available.
1-1-2. MANUAL:
SETUP MENU
1 / 2
SCENE SELECT
PICT ADJUST
EZOOM
DIS
PRIVACY MASK
MOTION DET
SYS SETTING
OFF
OFF
OFF
EXIT
FULL AUTO
ADVANCED MENU
1 / 2
SHUTTER/AGC
WHITE BAL
HLC/BLC
WDR/ATR-EX
DNR
DAY/NIGHT
IR OPTIMIZER
RETURN
AUTO
ATW
OFF
WDR
NIGHT
ON
> FULL AUTO: Optimized for the general scene.
> INDOOR: Optimized of indoor environment.
> OUTDOOR: Optimized of outdoor environment.
> BACKLIGHT: Optimized for backlight condition such as near the window in daylight.
> ITS: Optimized for the environment on traffic roads.
> CUSTOM: Setting for user customized environment.
14
Automatically tracks the changes of color temperature and continuously adjusts
the white balance. The white balance range is 1,800°K~10,500°K.
Note: If you set to ‘CUSTOM’ mode in ‘SCENE SELECT’ menu, the ‘WHITE BAL’
sub-menu will be appeared ‘ATW/ PUSH/ USER1/ USER2/ MANUAL/
PUSH LOCK’ functions that you can select one.
Other modes in ‘SCENE SELECT’ menu, the ‘WHITE BAL’ sub-menu is only ‘
ATW’ function.
Can set the WHITE BALANCE mode.
1-2. WHITE BAL
ATW
SPEED
DELAY CNT
ATW FRAME
ENVIRONMENT
200
RETURN
INDOOR
020
200
Sets the AWB(Automatic White Balance) compensating speed. Lower value makes
AWB faster. * Too fast AWB may make the color oscillation.
• SPEED (default: 200):
1-2-1. ATW (Auto Trace White Balance):
Video level is fixed in any conditions by the setting of SHUTTER, AGC MAX.
1-1-3. FIX:
Adjusts the AWB compensation delay to next update of AWB.
The smaller value will update AWB more frequently (faster).
• DELAY CNT (default: 20):
Determines the ATW range with respect to the fundamental range. Higher value
extends the ATW range at lower and higher color temperature.
• ATW FRAME (default: 200):
Selects INDOOR, SUNNY, SHADE or AUTO
Their ATW is optimized for the limited application and can not cover
• ENVIRONMENT (default: INDOOR):
15
1-3. HLC/BLC
> INDOOR : Optimized for Indoor installation and more easily compensates ATW
for low color temperature such as incandescent lights.
> SUNNY : Optimized for outdoor sunlight applications and more easily compensates
ATW for high color temperature such as sunlight.
> SHADE : Optimized for shade area compensation.
> AUTO : Optimized for general scene.
Disables HLC and BLC functions.
1-3-1. OFF:
HLC (Highlight Cut out) :
This function is used to black out highlighted areas, in order to enable a clear visual
image of objects, such as the license plates of an oncoming vehicle or other objects
that may be obstructed by headlamps.
HLC OFF HLC ON
BLC OFF BLC ON
BLC (Backlight Compensation) :
This function is used to brighten an image in the foreground with a highly light area
behind it such as sunlight, limiting the affect of silhouette.
16
Sets enabling/disabling ATR compensation for the better dynamic range (D-WDR)
of the image.
ATR feature improves the dynamic range and the visibility of the image by providing
the optimal gradation compensation of the image in one field. This is achieved by
two ways of image processing, luminance compression and contrast enhancement,
so that the tone can be enhanced at highlight and dark area.
Defines the threshold level for HLC. Lower value masks more.
• CLIP LEVEL (default: 10):
HLC clips out the highlight area and masks it as black color.
Video will be clipped out and masked for the area which exceeds CLIP LEVEL.
1-3-2. HLC:
1-4-1. WDR(Wide Dynamic Range): (VTC-C960WS)
1-4-2. ATR-EX (Adaptive Tone Reproduction-EX): (VTC-C960DS)
• CONTRAST (default: MID): It can be selected only in ‘CUSTOM’ scene preset.
• CLEAR FACE (default: MID): Selects one of ‘LOW/MID/HIGH’
1-4. WDR/ATR-EX
This function is extended the gain range of the screen that is mostly useful if camera
takes a simultaneous picture of both indoor and outdoor nearby window. It improves
contrast of the picture in outdoor scenery as well as indoor.
Video outputs image processed from two images by dual shutter (long and short shutter)
in a field to provide the best dynamic range. Highlight area is compensated by the short
shutter and dark area is compensated by the long shutter.
Final video may have less contrast compared to the conventional camera which does
not have WDR function.
1-5. DNR
DNR(Digital Noise Reduction) function improves picture quality by filtering out signal
noise which is generated under the low light conditions. It is 3DNR(3-dimensional noise
reduction) which reduces the noise by the multi frames. Noise Reduction is effective
at low light. Setting high level is strength of noise reduction but the result may occur in
loss of sharpness and the tail effect of a comet.
Sets BLC function enables or disables
1-3-3. BLC:
Note: BLC is available only in ‘CUSTOM’ scene preset.
Note: WDR is fixed except ‘CUSTOM’ scene preset.
Selects one of ‘WDR/ATR-EX/OFF’ is only in ‘CUSTOM’ scene preset.
17
AUTO mode in DAY/NIGHT is used only for a camera which does not have a light
sensor. Camera switches DAY from/to NIGHT automatically along with the amount
of light through the lens.
DAY/NIGHT is switched by amount of light through the lens.
Selects one of ‘INT/EXT1/EXT2’
• CNTL SIGNAL (default: INT):
1-6-1. AUTO
DAY→NIGHT is a threshold level which determines to switch from DAY to NIGHT.
Lower(Higher) value makes the camera switch from Day to Night at lower(higher)
illumination. If it stays in Day(Color) mode at night time, increase DAY→NIGHT
threshold value until it just switches to Night.
* Examine and verify Day/Night operation according to IMPORTANT ACTIVITY
• DAY -> NIGHT (default: 80)
D/N AUTO SETUP
BURST
CNTL SIGNAL
DELAY CNT
DAY->NIGHT
NIGHT->DAY
003
RETURN
OFF
INT
080
120
BURST determines whether a color burst signal keeps output or eliminated when
camera switches to B/W.
If set to ON, B/W video signal contains color burst signal and is compatible with
the color equipment but shows the same resolution as color video.
If set OFF, the color burst signal is removed from B/W video and shows better
resolution but rarely the compatibility problem may occur with the color equipment.
• BURST (default: OFF)
DELAY CNT is time in second while camera maintains its status before Day↔
Night switches. DELAY can avoid the unwanted/frivolous switching by a short
term lights such as light from the passing car.
• DELAY CNT (default: 3)
1-6. DAY/NIGHT
This function is used to control the setting during day-time and night-time operation.
18
1-6-2. DAY :
1-6-3. NIGHT :
• Verify ‘DAY/NIGHT’ after completing all settings of lens for zoom and focus.
• If the gap between DAY->NIGHT and NIGHT->DAY is too small, camera may repeat
switching DAY from/to NIGHT. If NIGHT->DAY is decreased from the Factory default,
the same amount is recommended for DAY->NIGHT to avoid repeating
DAY<->NIGHT unintentionally.
CAUTION
DAY->NIGHT and NIGHT->DAY operations must be examined and verified at
the final installation.
Block the lens for a few seconds for NIGHT mode and release and let it return to
DAY mode. If camera stays at NIGHT mode more than 10sec, decrease NIGHT->
DAY THRES a little and repeat the fore-mentioned steps. If the scene is too dim
or lens iris was adjusted too low(near close), it may not return to DAY.
IMPORTANT ACTIVITY
• BURST (default: OFF) :
NIGHT→DAY is a threshold level which determines to switch from NIGHT to DAY.
Lower(Higher) value makes the camera switched from Night to Day at lower
(higher) illumination. If it stays in Night(B/W) mode at day time, decrease NIGHT->
DAY threshold value until it just switches to Day
* Examine and verify Day/Night operation according to IMPORTANT ACTIVITY
• NIGHT -> DAY (default: 120)
Sets the BURST option ON/OFF to output burst signal in B/W mode.
The camera is always in B/W mode.
The camera is always in Color mode.
19
• DAY/NIGHT : Follows the setting of DAY/NIGHT function.
• OFF : Turns IR LED off.
• FIX : Fixes the brightness of IR LED in any condition.
IR OPTIMIZER SETUP
MODE
IR AREA
LEVEL
IR LED
COLOR NIGHT
IR SHADE COMP
002
RETURN
AUTO
---
DAY/NIGHT
OFF
OFF
SET1
MID
IR LED AUTO
LEVEL MIN
LEVEL MAX
006
RETURN
255
IR SHADE COMP SETUP
PATTERN
POSH
POSV
LEVEL
006
RETURN
255
1-7. IR OPTIMIZER
1-7-1. MODE : AUTO
Reducing the over-saturation is automatically adjusted along with the location of
the subject.
1-7-3. LEVEL (default: 002):
1-7-2. IR AREA :
Sets the IR OPTIMIZER AREA and the function works selected area in
‘CUSTOM’ preset only.
This function is used to adjust the overall brightness when IR OPTIMIZER is
working. If the LEVEL is too high, the over-saturation could occur.
1-7-4. IR LED: Sets the IR LED ON/OFF controlling
1-7-5. COLOR NIGHT (default: OFF): Displays night video in color.
1-7-6. IR SHADE COMP (default: OFF):
This function is used to compensate
for IR shade of the side area on screen
when IR LED is ON. You can adjust
the shading PATTERN, POSITION
and LEVEL.
If the LEVEL is high, the screen noise
could be increased at the side area.
This function is effective built-in LED models in NIGHT mode only.
If subjects which can cause overexposure are located near the monitored area, you
can adjust IR OPTIMIZER level or area.
20
LENS SHD COMP
PATTERN
POSH
POSV 290
RETURN
SET1
480
PICT ADJUST
BRIGHTNESS
CONTRAST
SHARPNESS
HUE
COLOR GAIN
128
32
08
064
128
RETURN
1-8. LENS SHD COMP (default: OFF)
This function is used to caculate the compensation data for lens shading.
Convex shape of the lens causes the light to enter the camera unevenly and typically
makes the center of the screen brighter than the rest. It is used to compensate for this
undesirable effect and make the screen more even.
Set to ‘ON’, you can adjust the shading PATTERN and POSITION.
1-9. DEFOG (default: ON)
1-10. FLK LESS (default: AUTO)
1-11. ANTI-CR (default: AUTO)
2. PICT ADJUST
This function is used to carry out defog function. Sets LEVEL to eliminate amount of
fog on screen.
If the DEFOG is set to ON, the WDR/BLC function will be deactivated.
This function is used to remove the flickering on screen due to differences in light and
electric frequencies.
This mode can minimize the problems related to color rolling caused by differences
between the flicker of fluorescent lights and the frequency of the camera.
21
Increases or decreases the brightness of the picture.
This is different from that of DC iris lens and simply increases or decreases the digital
gain of video. Do not increase this too much, the dynamic range for the highlight area
will decrease.
2-1. BRIGHTNESS (default: 120):
2-2. CONTRAST (default: 033):
MAG is the magnification ratio of the electronic zoom. Sets from x000 to x255.
3-1. MAG (default: 000):
When MAG is greater than 0, the electronic pan is available.
000 is the left most pan and 1023 is the right most pan.
3-2. PAN (default: 512):
When MAG is greater than 0, the electronic tilt is available.
000 is the upper most tilt and 511 is the lower most tilt.
3-3. TILT (default: 256):
Increases or decreases the sharpness of the picture.
Too much sharpness can make image harsh and show more noise as well as line
flicker at the edge of object in the picture.
2-3. SHARPNESS (default: 008):
2-4. HUE (default: 064): Adjusts hue for NTSC version only.
2-5. COLOR GAIN (default: 128): Increases or decreases the color saturation.
Sets the maximum digital zoom magnification. E.ZOOM function enlarges the pixel
itself, which can cause deterioration of the picture quality.
3. EZOOM
This function is used to reduce and stabilizes the shaky image from a camera installed
in the vibrated area. FOV(Field of view) will be reduced if set to ON.
4. DIS (Digital Image Stabilization)
Adjusts the strength of the image contrast. If set to too high, the dark area may loss
detail and the high luminance area may saturate.

Termékspecifikációk

Márka: Vitek
Kategória: nincs kategorizálva
Modell: VTC-C960WS

Szüksége van segítségre?

Ha segítségre van szüksége Vitek VTC-C960WS, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók nincs kategorizálva Vitek

Vitek

Vitek VTC-C594DN Útmutató

8 Október 2024
Vitek

Vitek VT-TPTZ10HR-2T Útmutató

7 Október 2024
Vitek

Vitek VTM-LCD155P Útmutató

7 Október 2024
Vitek

Vitek VTC-T4T3HR2MD Útmutató

6 Október 2024
Vitek

Vitek VTC-C01P Útmutató

27 Szeptember 2024
Vitek

Vitek VT-1205A-D4B Útmutató

17 Szeptember 2024
Vitek

Vitek VTC-BM3FP Útmutató

14 Szeptember 2024
Vitek

Vitek VTC-THB5RV Útmutató

14 Szeptember 2024
Vitek

Vitek VTD-VH412VP4 Útmutató

13 Szeptember 2024
Vitek

Vitek VTD-HOCRAZ Útmutató

11 Szeptember 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

Moen

Moen Belfield YB6418BN Útmutató

3 Április 2025
Moen

Moen Belfield YB6424BN Útmutató

3 Április 2025
Scotsman

Scotsman MDT5N25 Útmutató

3 Április 2025
Scotsman

Scotsman FME2404 Útmutató

3 Április 2025
Schwaiger

Schwaiger ISPK0100 Útmutató

3 Április 2025
Schwaiger

Schwaiger PE900 531 Útmutató

3 Április 2025
Schwaiger

Schwaiger 661521 Útmutató

3 Április 2025
Schwaiger

Schwaiger HSA600 532 Útmutató

3 Április 2025
Schwaiger

Schwaiger LADV2025 Útmutató

3 Április 2025
Schwaiger

Schwaiger 658668 Útmutató

3 Április 2025