Használati útmutató Techno Line WS 9252

Techno Line Időjárás állomás WS 9252

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Techno Line WS 9252 (6 oldal) a Időjárás állomás kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/6
Please read the instructions carefully and keep the manual well for future reference.
1. Remove the battery door of the main unit and transmitter.
2. Install 2 new AA size batteries for both main unit and transmitter, according to the polarity mark on
the battery compartment.
3. Replace the battery door.
4. After the batteries are installed, all LCD segment will be shown.
5. Press the “RESET” key of main unit first, and press the “RESET” key of transmitter.
6. It will automatically receive 433 MHz signal from transmitter for channel test in 8 seconds.
7. After 5 minutes channel test, it will turn to RC signal reception automatically.
8. Radio controlled function, the current time & date automatically synchronized with the time signal
transmitted from Germany(DCF77).
1. The unit can operate up to 3 remote transmitters.
2. Position the unit and transmitter within the effect transmission range: 50 meters in usual ive
circumstances.
3. In some cases, you may not receive the signal immediately, you can reset the unit and transmitter
again as described above.
1. LCD display
- Display of the time, alarm time, outdoor & indoor temperature & humidity and weather forecast.
2. SNOOZE / LIGHT key
- Press it to turn on backlight for 5 seconds.
- When the alarm is sounding, press it to stop the current alarm and activate snooze.
3. ALARM SET key
- Press it to display alarm time for 5 seconds. During alarm time displayed, press it to turn on/
off alarm function.
- Press and hold it for 3 seconds to enter alarm setting mode.
- In alarm setting mode, press it to step the setting item, and press it to save and exit the setting.
4. CH/+ key
- In normal mode, Press it to select channel 1 to channel 3.
- Press and hold it for 3 seconds to turn to channel auto-change mode. Press it again to return to
normal mode.
- In setting mode, press it to adjust the value of the flashing digit upwards. And press it without
releasing to speed up the setting.
5. MEM/- key
- In normal mode, press it to check the max./min. indoor and outdoor temperature record for 5
seconds.
- Press and hold it for 3 seconds to delete the max./min. temperature record.
- In setting mode, press it to adjust the value of the flashing digit downwards. And press it without
releasing to speed up the setting.
6. DISPLAY SET key
- In normal mode, press and hold it for 3 seconds to enter time setting mode.
- ime setting mode, press it to step the setting item, and press and hold it for 3 seconds to save and In t
exit the setting.
7. °C/°F slide switch
- Select temperature unit between °C/°F.
8. SENSOR key
- Press it to start 433 MHz channel test for main unit & transmitter.
- During the channel test, press and hold it for 3 seconds to manual turn off.
9. RCC key
- Press it to manual receive RC signal.
- During the RC reception, press and hold it for 3 seconds to turn off synchronisation.
10. RESET key
- In case of m -function, press it by using a metal wire to reset all the values. al
11. Battery door
1. LED indicator
- Flashes when the remote unit transmitting a reading.
- Display of the channel, temperature and humidity.
2.LCD display
3. CHANNEL slide switch
- Assign the transmitter to Channel 1, 2 or 3.
4. RESET key
- Press it to reset the transmitter.
5. Wall-mounting holder
- Use it to support the transmitter on the wall.
6. Battery compartment
The signal indicator flashing means time signals are being received. If the RC weather station receives
signal successfully, a sync-time symbol “ ” appears on the LCD. The unit has already received the
time signal. Otherwise, the signal strength symbol will disappear from the LCD display.
You may press “RCC” key to receive the time signal manually. The receive mode will be off
automatically after 6-16 minutes. Receive mode consumes more battery power that may reduce
battery lifetime.
The weather station has been programmed to automatically switch when daylight saving time is in
effect. Your weather station will display “DST” on the LCD during the summer.
If the weather station does not receive the time signal successfully, you can set the time manually. As
soon as the transmitter is received again, the clock will automatically synchronize with the received
time.
1. In normal mode, press and hold “DISPLAY SET” key for 3 seconds until the Hour format digit
flashing.
2. Press - “+” / “ ” key to select 12/24 hour format.
3. Press “DISPLAY SET” key again to step the setting item to Hour with the Hour digit flashing.
4. Press “+” / “ ” key to adjust the value of the- flashing digit.
5. Do the above operation in this sequence: 12/24 Hr > Hour > Minute > Second > Time difference.
6. Press and hold “DISPLAY SET” key for 3 seconds to save and exit the setting.
If your local time is different from the RC received time, you can set the desired time difference. The
available time difference is from -23 hours to +23 hours. After setting the desired time difference, the
weather station will show the time that RC received time plus/minus the time difference.
1. In normal mode, press and hold “ALARM SET” key for 3 seconds until the Hour digit flashing.
2. Press “+” / “ ” key to adjust the value of the- flashing digit.
3. Press “ALARM SET” key again to step the setting value to Minute with the Minute digit flashing.
4. Press “+” / “ ” key to adjust the value of the- flashing digit.
5. Press “ALARM SET” key to save and exit the setting.
1. In alarm mode, the “AL” icon will display on the LCD.
2. The alarm function will turn on automatically once you set the alarm time.
1. Set the desired alarm time as described in the above section.
2. Or press “ALARM SET” key to display the alarm time, press it again to turn on alarm function with
the alarm icon “ ” displayed on the LCD.
3. When weather station reach the alarm time, alarm sound ll start. Where, it can be stopped by wi
following operation:
a). Auto-stop after two minutes alarming if without any operation and it will re-alarm by the next day.
b). By pressing “SNOOZE” key to enter snooze that the alarm will sound again after 5 minutes.

Termékspecifikációk

Márka: Techno Line
Kategória: Időjárás állomás
Modell: WS 9252

Szüksége van segítségre?

Ha segítségre van szüksége Techno Line WS 9252, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Időjárás állomás Techno Line

Techno Line

Techno Line WS 9632 Útmutató

5 Január 2025
Techno Line

Techno Line WS 9620 Útmutató

28 December 2024
Techno Line

Techno Line WS 9310 Útmutató

28 December 2024
Techno Line

Techno Line WS 9135 Útmutató

28 December 2024
Techno Line

Techno Line WS 6870 Útmutató

28 December 2024
Techno Line

Techno Line WS 9450 Útmutató

28 December 2024
Techno Line

Techno Line WS 9257 Útmutató

28 December 2024
Techno Line

Techno Line WS 9125 Útmutató

28 December 2024
Techno Line

Techno Line WS 9060 Útmutató

28 December 2024
Techno Line

Techno Line MA 10920 Útmutató

28 December 2024

Útmutatók Időjárás állomás

Legújabb útmutatók Időjárás állomás

TFA

TFA 35.1044.55.IT Útmutató

31 Március 2025
Bresser

Bresser Translucidus NV Útmutató

27 Március 2025
Bresser

Bresser ClimaTemp TB Útmutató

27 Március 2025
Ventus

Ventus K0382 Útmutató

14 Január 2025
Alecto

Alecto WS-1200 Útmutató

13 Január 2025
TFA

TFA 20.1082.17 Útmutató

13 Január 2025
Oregon Scientific

Oregon Scientific BAR310HG Útmutató

12 Január 2025
Oregon Scientific

Oregon Scientific BAR 898 Útmutató

12 Január 2025
Auriol

Auriol AHFL 433 B2 Útmutató

12 Január 2025
Davis

Davis Weatherlink Touch Console Útmutató

11 Január 2025