Használati útmutató Supermicro SuperServer 1028UX-LL3-B8

Supermicro szerver SuperServer 1028UX-LL3-B8

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Supermicro SuperServer 1028UX-LL3-B8 (1 oldal) a szerver kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/1
http://www.supermicro.com MNL-1702-QRG
Board Layout
SuperServer 1028UX Series Quick Reference Guide
Rear View
CPU Installation
Beep Codes
Front View & Interface
Heatsink Installation
1. Place the heatsink on top of the installed CPU.
2. Align the four screws to the socket.
3. Holding the heatsink in place, screw down as shown
(cross pattern, in order: A, C, B, D).
4. Note: Only use 6-8 lb/f of torque; otherwise, hand-tighten
each screw to avoid damaging the CPU.
Memory
Caution
Align CPU to socket;
install CPU straight down
NOTE:
Do not bend pin inside socket
!
SAFETY INFORMATION
IMPORTANT: See installation instructions and safety warning
before connecting system to power supply.
http://www.supermicro.com/about/policies/safety_information.cfm
WARNING:
To reduce risk of electric shock/damage to equipment,
disconnect power from server by disconnecting all power
cords from electrical outlets.
If any CPU socket empty, install protective plastic CPU cap
CAUTION:
Always be sure all power supplies for this system have
the same power output. If mixed power supplies are
installed, the system will not operate.
For more information go to :
http://www.supermicro.com/support
!
!
!
Power LED
Device Activity LED
LAN1 LED & LAN2 LED
Universal Information LED
Power Button
UID Button
Hard Drive Signal
Hard Drive Fail
Descrip iot nNo.
1
2
3
4
5
6
7
8
HDD 1
(S A3)AT
HDD 3
(S A3)AT
HDD 5
(S A3)AT
HDD 0
(S A3)AT
HDD 2
(S A3)AT
HDD 4
(S A3)AT
HDD 6
(S A3)AT
HDD 8
(S A3)AT
(S A3/AT
NVMe)*
Descrip iot n
No.
SXB1_1/1_2/1_3: PCI-E 3.0 (x16 + x16) Left Riser Card Slot
SXB2: PCI-E 3.0 (x8) Center Riser Card Slot
JBT1: CMOS Clear
S-SATA0~3: SATA 3.0 Ports (Intel SCU)
I-SATA0~5: SATA 3.0 Ports (Intel PCH)
JSD1/JSD2: SATA DOM (Device_on_Module) Power Connectors
SXB3_1/3_2/3_3: PCI-E 3.0 (x8 internal) Right Ultra Riser Card Slot
P1-DIMMA1(Blue)/P1-DIMMA2 slot
P1-DIMMB1(Blue)/P1-DIMMB2 slot
CPU1 (Install CPU1 first)
P1-DIMMD1(Blue)/P1-DIMMD2 slot
P1-DIMMC1(Blue)/P1-DIMMC2 slot
P2-DIMME1(Blue)/P2-DIMME2 slot
P2-DIMMF1(Blue)/P2-DIMMF2 slot
CPU2
P2-DIMMH1(Blue)/P2-DIMMH2 slot
P2-DIMMG1(Blue)/P2-DIMMG2 slot
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
HDD 7
(S A3)AT
HDD 9
(S A3)AT
(S A3/AT
NVMe)*
78
2 14 3
56
Descrip iot n
No.
19 3
1
2
3
4
5
6
7
8
9
28 67 4
2 PCI-E 3.0 p1-x16 (CPU1/CPU2) Expansion Slots
(Full-height 4.2”, Length 10.5”)
PCI-E 3.0 p1-x8 (CPU2) Expansion Slot
( Low Profile (2.536”), Half Length (6.6”))
VGA Port
UID Button (Unit Identifier Button)
COM Port
Dedicated LAN for IPMI
USB 3.0 Ports
LAN Ports (4)
Redundant Power Supply Module
5
Screw #B Screw #A
Screw #C Screw #D
* r N M els Fo od
X10DRU-X
I-SGPIO2
JF1
JL1
DESIGNED IN USA
JUSBA1
JBAT1
JBT1
JSD 2
JSD1
SP1
LED_H1
LED_G2
LED_G1
LED_H2
LED_F2
LED_E1
LED_E2
LED_F1
LED_C2
LED_C1
LED_D1
LED_B2
LED_A1
LED_A2
JIPMB1
FAN8
FAN7
FAN6
FAN5 FAN4 FAN3 FAN2 FAN1
JVRM2
JVRM1
JWD2
JPG1
JPB1
LED1
JUIDB2
SXB3_2
PSU2 PSU1
JGPW2
JGPW3
JGPW1
JPW22JPW23
JPW21
JGPW4
JPW19
JTPM1
SXB1_3
SXB3_3
SXB1_1
SXB3_1
P2-DIMMG2
P2-DIMMG1
P2-DIMMH1
P2-DIMMH2
CPU2
SXB1B
SXB1C
SXB1A
CPU1_PORT3CPU2_PORT2 USB3/4 (3.0)
JPME2
GPU PWR3GPU PWR2
CPU2_PORT1
SXB2
VGA
P2-DIMMF2
P2-DIMMF1
GPU PWR4
I-SATA4
P2-DIMME2
P2-DIMME1
I-SATA5
S-SATA0~3
COM1
I-SATA0~3
IPMI_LAN
USB 0/1(3.0)
CPU1_PORT2
P1-DIMMC1
P1-DIMMC2
P1-DIMMD2
P1-DIMMD1
CPU2_PORT3CPU1_PORT1
CPU1
P1-DIMMB2
P1-DIMMB1
P1-DIMMA2
GPU PWR1
P1-DIMMA1
BP PWR2 BP PWR1
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
SXB1_2
PLD1
C612
A1
LED_D2
LED2HDD_LED1
1
LED_B1
BMC
BMC_HB_LED1
JA1
8
910
11
1215 13
14
16
17
12 3 46 75
For memory to work properly, follow the tables below for memory installation.
Pro sors and their Co s ng mory M les ces rre pondi Me odu
CPU# Corresponding DIMM Modules
CPU 1 P1-DIMMA1 P1-DIMMB1 P1-DIMMC1 P1-DIMMD1
CPU2 P2-DIMME1 P2-DIMMF1 P2-DIMMG1 P2-DIMMH1
Pro sor and mory M le lat n for Optimal P fo anceces Me odu Popu io er rm
Number of
CPUs+DIMMs
1 CPU &
2 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1
1 CPU &
4 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1
2 CPUs &
4 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1
2 CPUs &
6 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1
2 CPUs &
8 DIMMs*
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1
/P2-DIMMH1
2 CPUs &
10~16 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1
/P2-DIMMH1 + Any memory pairs in P1, P2 DIMM slots
2 CPUs &
16 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1
/P2-DIMMH1, P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/P2-DIMMF2
/P2-DIMMG2/P2-DIMMH2
Beep Code/LED Error Message Description
1 beep Refresh Ready to boot
5 short beeps + 1 long beep Memory error No memory detected in the system
5 beeps No Con-In or No
Con-Out devices
Con-In: USB or PS/2 keyboard, PCI or Serial
Console Redirection, IPMI, KVM or SOL
Con-Out: Video Controller, PCI or Serial
Console Redirection, IPMI, SOL
1 beep per device Refresh 1 beep for each USB device
Rev 1.0a
Note:
1028UX-LL1 includes 2643 v3/v4, 1028UX-LL2 includes 2687W v3/v4 and 1028UX-LL3 includes 2689 v4
Pre-populated with 8 * 8GB memory DIMMs.
By default BIOS is set to force memory to highest frequency 2133/2400 (v3/v4) whether its 1DPC or 2DPC
CPU and Memory Population Configuration Table
(For memory to work properly, follow the instructions below)
Populating RDIMM/LRDIMM DDR4 Memory Modules
Type
Ranks
Per DIMM
and Data
Width
DIMM Capacity
(GB)
Speed (MT/s); Voltage (V); Slots per Channel (SPC) and
DIMMs per Channel (DPC)
2 Slots per Channel
1 DPC 2 DPC
E5-2600 V3 E5-2600 V4 E5-2600 V3 E5-2600 V4
4 GB 8 GB 1.2 V 1.2 V 1.2 V 1.2 V
RDIMM SRx4 8 GB 16 GB 2133 2400 1866 2133
RDIMM SRx8 4 GB 8 GB 2133 2400 1866 2133
RDIMM DRx8 8 GB 16 GB 2133 2400 1866 2133
RDIMM DRx4 16 GB 32 GB 2133 2400 1866 2133
LRDIMM QRx4 32 GB 64 GB 2133 2400 2133 2400
LRDIMM 3DS 8Rx4 64 GB 128 GB 2133 2400 2133 2400
ÌMNL-1702-QRG-10aÄÎ

Termékspecifikációk

Márka: Supermicro
Kategória: szerver
Modell: SuperServer 1028UX-LL3-B8

Szüksége van segítségre?

Ha segítségre van szüksége Supermicro SuperServer 1028UX-LL3-B8, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók szerver Supermicro

Supermicro

Supermicro SBA-4119S-T2N Útmutató

12 Január 2025
Supermicro

Supermicro A+ Server 1024US-TNR Útmutató

12 Január 2025
Supermicro

Supermicro SuperServer 2028U-TNRT+ Útmutató

11 Január 2025
Supermicro

Supermicro SuperServer 2028TR-HTFR Útmutató

9 Január 2025
Supermicro

Supermicro SuperBlade SBI-4129P-C2N Útmutató

29 December 2024
Supermicro

Supermicro SuperServer F619P2-RC1 Útmutató

29 December 2024
Supermicro

Supermicro SuperServer E300-9A-4C Útmutató

29 December 2024
Supermicro

Supermicro SuperServer 5029AP-TN2 Útmutató

29 December 2024
Supermicro

Supermicro SuperServer 5038K-I-NF3 Útmutató

29 December 2024
Supermicro

Supermicro SuperServer 5019A-FTN10P Útmutató

29 December 2024

Útmutatók szerver

Legújabb útmutatók szerver

Seagate

Seagate DS215+ Útmutató

9 Április 2025
Ibm

Ibm PureFlex System x240 Útmutató

3 Április 2025
Asus

Asus Z11PR-D16 Útmutató

2 Április 2025
Teradek

Teradek Cube 655 Útmutató

29 Március 2025
Teradek

Teradek Cube 505 Útmutató

29 Március 2025
Teradek

Teradek VidiU Pro Útmutató

29 Március 2025
Synology

Synology RS2414+ Útmutató

24 Március 2025
Synology

Synology DiskStation DS713+ Útmutató

24 Március 2025
MSI

MSI D3052 Útmutató

15 Január 2025
MSI

MSI G3101 Útmutató

15 Január 2025