Használati útmutató Summit FF7LBIMED

Summit hűtőszekrény FF7LBIMED

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Summit FF7LBIMED (16 oldal) a hűtőszekrény kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/16
If you need service or call with a question, please have this information ready. We
advise you to keep this Owners Manual in your possession.
Model: Options added:
Serial number:
Date of Purchase ______________________ Where Purchased___________________
Felix Storch, Inc.
SUMMIT APPLIANCE DIV.®
USE AND CARE GUIDE
• FF6 Series
• FF7 Series
• FS62 Series
• SCR600 Series
• CT66 Series
• SWC6G Series
• CT67 Series
• FF8 Series
AL650 series
AL750 series
ALF620 series
24 inch wide all refrigerators
24 inch wide all-freezers
24 inch wide wine cellars
24 inch wide refrigerator-freezers
Felix Storch, Inc.
SUMMIT APPLIANCE DIV.
Page 2
Your safety and the safety of others are very important to us.
We have provided many important safety messages in this manual and on your
appliance. Always read and obey all safety messages.
You can be killed or seriously injured if you do not follow these instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the
chance of injury, and tell you what can happen if the instructions are not followed.
• Plug into a grounded 3 prong outlet.
• Do not remove ground prong, nor use a 3/2 adapter
• Do not use an extension cord.
• Use care not to plug into outlets controlled by wall switches.
• Disconnect power before servicing.
• After servicing, replace all parts and panels before operating.
• Use nonflammable cleaners.
• Keep flammable materials and vapors, such as gasoline, away from appliances.
• Use two or more people to move and install appliance.
• Drawer refrigerators are provided with anti-tip brackets. Always install prior to use.
Proper Disposal of Your Old Appliance
Old appliances can represent a suffocation hazard to children
• Remove doors from your old appliance.
• Leave shelves in place.
• If an old appliance contains refrigerants; it must be recycled by a licensed service or
disposal company.
APPLIANCE SAFETY
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: To reduce the risk of fire, electric shock, or injury when
using your refrigerator/freezer, follow these basic precautions:
Felix Storch, Inc.
SUMMIT APPLIANCE DIV.
Page 3
Excessive Weight Hazard! * Use two or more people to move and install your appliance.
Failure to do so can result in back or other injury.
ALLOW APPLIANCE TO SIT UPRIGHT FOR 24 HOURS BEFORE TURNING ON, TO ALLOW THE
COMPRESSOR LUBRICANT TO DRAIN.
1. Remove Packaging Materials
2. Remove tape and glue residue from surfaces before turning on the appliance. Rub a small
amount of liquid dish soap over the adhesive with your fingers. Rinse with warm water and dry.
3. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to
remove tape or glue. These products can damage the surface of your appliance.
4. When Moving Your Appliance:
Your appliance is heavy. When moving the appliance for cleaning or service, be sure to protect
the floor. Always pull the appliance straight out when moving it. Do not wiggle or “walk” the
appliance when trying to move it, because floor damage can occur.
5. Clean Before Using
After you remove all of the packaging materials, clean the inside of your appliance before using
it. See the cleaning instructions in “Appliance Care.”
6. All upright models have level legs in the front and many also have them in the rear. Level as
necessary for best operation.
7. If your appliance has casters, after moving into place, lock the brakes on those casters
supplied with brakes. Always unlock before moving the appliance for cleaning.
Keep flammable materials and vapors, such as gasoline, away from appliances. Failure to do so can result in
explosion, or fire.
IMPORTANT: Do not install the appliance near an oven, radiator, or other heat source, nor in a
location where the temperature will fall below 45°F (7°C). Do not place in direct sunlight.
Check the strength of the floor before installing your appliance. It should hold the weight of a
fully loaded appliance. Allow at least 1” (2.5 cm) of airspace at the top and on both sides of the
appliance and 1” (2.5 cm) between the back of the appliance and the wall. If the appliance is
going to be placed against a wall, if possible, leave extra space on the hinge side so the door can
open wider than its width (to make it easier to remove shelves or storage bins).
NOTE: This appliance may be installed side by side with another appliance. Allow for a 3’’ (7.5
cm) clearance at the top and sides, and a ¼” (0.64 cm) clearance between the appliances.
The greater the airflow and ventilation you provide for your appliance—the higher its energy efficiency and
performance will be.
INSTALLATION INSTRUCTIONS
LOCATION REQUIREMENTS
UNPACKING
Felix Storch, Inc.
SUMMIT APPLIANCE DIV.
Page 4
CHOOSING THE RIGHT PLACE
Place the appliance in a dry and regularly ventilated place. It is nce always be operated in an recommended that this applia
ambient temperature of at least 60°F and under 85°F. The appliance may be exposed to lower or higher temperatures but only for a
short period of time and the temperature should never be lower than 45°F. Never place the appliance near heat emitting devices
(e.g. cooker, radiator, water heater or similar devices) and do not expose it to direct sunlight.
RECOMMENDED GROUNDING METHOD
A 115 Volt, 60 Hz. AC only 15- or 20- amp fused or circuit breaker, grounded electrical supply is required. It is recommended that a
separate circuit serving only your appliance be provided. Use outlets that cannot be turned off by a switch or pull chain. Connect
this appliance to a 3 prong power supply socket outlet (which has a ground terminal). If you only have a two prong outlet have it
replaced by a qualified technician with an outlet that meets the local codes. DO NOT USE AN EXTENSION CORD. Required
nominal voltage and frequency are indicated on the rating plate. The connection to the power supply and grounding has to be
made according to current standards and regulations. The appliance resists temporary voltage tolerance from -15 to 10%.
ON OUTDOOR MODELS ONLY
NEVER USE INDOOR RATED APPLIANCES OUTDOORS. Summit manufactures refrigerators and freezers specifically for outdoor
use and these are the only ones that should be used outdoors.
Electrical Shock Hazard. Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.
Many outdoor outlets are controlled by wall switches. Turning off power and on again may cause the GFCI switch to trip.
A GFCI (ground fault circuit interrupter) is built into every line cord. Do not defeat or bypass this important safety feature. The line
cord supplied with this appliance is specially designed for outdoor use. Use only a factory supplied replacement cord with a GFCI
(ground fault circuit interrupter) in the event the cord becomes damaged.
You may purchase these cords from either our sales or service department at 718-893-3900 (sales) or 718-328-8700 (service).
It can also be ordered online from www.summitapplianceparts.com
ENERGY SAVING TIPS
• The more airflow you can provide around an appliance, the less energy it will use.
• If your appliance needs defrosting, keep ice build-up to less than 1/2 inch.
• Keep doors or drawers open a minimum of time, and shut securely.
1. Locate the two front leveling legs taped among the packing materials. In most models these legs are already mounted into the
underside of the appliance.
2. Screw these legs into the front holes on the bottom of the appliance. The back of the appliance rests on two fixed supports.
(Built-in models also have rear level legs that can provide more precise leveling).
3. Adjust the front legs just enough to lift the cabinet up off of the floor.
4. Place a leveling tool on top of the appliance: first side to side, then front to back. Turn leg counterclockwise to raise a corner.
Turn leg clockwise to lower a corner.
5. Repeat Step 4 until appliance is level.
6. After appliance is fully loaded, recheck with level as in Step 4.
7. If your appliance is equipped with casters, the two front casters have brakes to prevent rolling. Keep brakes locked, and unlock
for moving only.
INSTALLATION INSTRUCTIONS
LEVELING YOUR APPLIANCE
Felix Storch, Inc.
SUMMIT APPLIANCE DIV.
Page 5
In order to ensure proper temperature, you need to permit proper airflow in the appliance. Do not block any air
vents. If the vents are blocked, airflow will be prevented, and temperature and moisture problems may occur.
Always position contents to allow some airflow between shelves or baskets.
Allow the appliance to cool at least 6 to 8 hours before adding contents. Allow 24 hours for temperature to
stabilize.
NOTE: When the appliance is first started, the compressor will run constantly until the appliance is cold, It may
take up to 6 or 8 hours (or longer), depending on room temperature and the number of times the appliance door is
opened. After the appliance is cooled, the compressor will turn on and off as needed to keep the appliance at the
proper temperature.
The outside of your appliance may feel warm. This is normal. The appliance’s design and main function is to
remove heat from packages and air space inside the appliance. The heat is transferred to the room air, making the
outside of the appliance feel warm. In some models the condenser that gets warm is inside the side walls, making
these walls warm to the touch.
REVERSING THE DOOR SWING (Selected models)
If you find the direction of opening the door on your appliance inconvenient, on some models you can change it.
Holes on the opposite side have already been prepared in the factory. On models with our wrapped stainless steel
door and 12 inch pro handle, (suffix SSTB, SSVH or CSS or with optional handles “TB” or “SH” ) you must order
these with either a right hand or left hand door swing in advance. These doors cannot be reversed. Models with a
suffix SSHH, BIFR, BIIF, and CSSHH can be reversed.
TO REVERSE YOUR DOOR
• Take off the upper hinge cover from the door and remove the screws that hold the top hinge.
• Lift the hinge straight up to free the hinge pin from the socket in the top of the door.
• Lift the door up away to free its bottom socket from the hinge pin.
• Remove the screws to the bottom hinge.
• Remove the decorative caps from opposite side and plug the holes from original side with the decorative caps.
• Move the bottom hinge to the opposite side and tighten the screws. Use any lock washers or nuts if they were
installed in the original installation.
• Replace door onto the hinge pin on the bottom hinge. Place top hinge pin into door. Insert screws into the top
hinge and tighten.
If you notice the door not hanging straight—loosen the top hinges, adjust the door until it is level and tighten the
screws.
APPLIANCE USE
Felix Storch, Inc.
SUMMIT APPLIANCE DIV.
Page 6
APPLIANCE OPERATION
Base Grill (some models only)
To Remove and Replace the Base Grill:
1. Open the appliance door and remove the base grill by pulling down and out from the top.
2. Replace the base grill by putting the clips in the openings in the appliance panel. Push in until the base grill snaps into place.
An optional stainless steel grill is available for some models (Models beginning with FF6, FF7, CT66, CT67, SCR600, FS62,
AL6, AL7, ALF6 and SWC6G ). You can order at www.summitapplianceparts.com
Changing the light bulb (some models only)
NOTE: Not all appliance bulbs will fit your appliance. Be sure to replace the bulb with one of the same size, shape, base size
and wattage. You can purchase bulbs from www.summitapplianceparts.com
1. Unplug appliance or disconnect power.
2. Remove the light shield. Most models do not require tools.
3. Replace the light bulb with an appliance bulb of the same wattage.
4. Replace the light shield.
5. Plug in appliance or reconnect power.
Loss of Power
After the power is restored, unplug the appliance for 30 minutes, to allow the refrigeration system to equalize. During this time
keep the door closed whenever possible.
REMEMBER: A full appliance stays cold longer than a partially filled one.
Moving Care
1. Remove all containers.
2. Unplug the appliance.
3. Clean it thoroughly.
4. Tape the appliance shut and tape the electrical cord to the cabinet.
When you get to your new location, refer to the “Installation Instructions” and “Appliance Use” sections for informa-
tion on installation and setting the controls.
When transporting appliances, it is recommended that you transport it upright.
If it is necessary to lay it down, lay on its side—never the front or back—and be sure to
check for water in the pan on top of the compressor before moving.
Felix Storch, Inc.
SUMMIT APPLIANCE DIV.
Page 7
APPLIANCE CARE
Cleaning Your Frost-Free Refrigerator
Use nonflammable cleaners.
Frost-free means that you do not have to defrost your appliance. Frost is removed by air moving and collecting any moisture
and depositing it on the cooling coil. The cooling coil periodically warms up enough to melt the frost, and the water then flows
down to the drain pan (located behind the base grill) where it is evaporated.
Complete cleaning should be done at least once a year.
1. Unplug appliance or disconnect power.
2. Remove all substances.
3. Wash the inside walls with a solution of mild detergent in warm water or 2 tbs (26 mg) baking soda to 1 qt (0.95 L) warm
water.
• Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes,
concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or
gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools. These can scratch or damage materials.
4. Rinse well and wipe dry with a clean soft cloth.
5. Use the appropriate cleaning method for your exterior finish.
Painted metal: Wash exteriors with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or
harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth. For additional protection against
damage to painted metal exteriors, apply appliance wax (or auto paste wax) with a clean, soft cloth. Do not wax plastic parts.
6. Plug in appliance or reconnect power.
7. Replace all containers.
Stainless steel: Clean stainless steel with special stainless steel cleaners only. Do not use bleach or any abrasive cleaners.
Cleaning your cycle defrost or manual defrost refrigerator
Cycle defrost models utilize a system, where ice builds up on the rear wall and melts when the compressor is off. Manual
defrost models continually build ice on inner walls.
NEVER USE A METAL OBJECT TO REMOVE ICE FROM THE REAR WALL. IF NEEDED, USE A PLASTIC ICE-
SCRAPER OR A HAIR DRYER.
Clean surfaces, using the same instructions as for frost-free models.
For CSS Models (completely stainless steel) or models with stainless steel doors and
handles; please use only cleaners especially made for stainless steel.
Felix Storch, Inc.
SUMMIT APPLIANCE DIV.
Page 8
TEMPERATURE SELECTION
YOUR APPLIANCE MAY HAVE A MECHANICAL (DIAL) OR DIGITAL THERMOSTAT.
INSTRUCTIONS FOR BOTH FOLLOW:
MECHANICAL THERMOSTAT INSTRUCTIONS
The refrigerator is controlled with a thermostat knob located inside the unit, towards the upper right-hand corner. Turn the knob clockwise from the
STOP (0) position toward the higher numbers for colder temperatures.
Temperature Controls
•Higher settings on the knob (higher numbers) mean lower temperatures (colder) in all compartments of the appliance.
On the coldest settings temperatures in some spots of the interior of the appliance may even drop below 32°F. Use
higher thermostat settings only when required or recommended. When the ambient temperature is normal, we
recommend the medium setting.
•Changes of the ambient temperature affect temperature in the interior of the appliance so choose a correct setting of the
thermostat knob, depending on your ambient conditions.
•In the STOP (0) position the appliance does not operate (the cooling system is switched off), yet power supply is not interrupted (the light is on, when
you open the refrigerator door).
•The temperature in the refrigerator and in the freezer compartment also depend on how often you open the door.
- In all small refrigerators and freezers without interior fans, temperatures are coldest near the bottom, and occasionally near the rear. Place contents
accordingly. It is best not to operate these units mostly empty. If temperatures are erratic, try putting some water bottles or freezer packs inside
to create a load for the compressor.
DIGITAL THERMOSTAT INSTRUCTIONS
If you find that it is necessary to change the temperature setting for your digital thermostat controlled appliance, please refer to the
following instructions. The front panel of the thermostat is illustrated here:
To see the SETPOINT:
Push and immediately release the SET key -the display will show the SET point value. Wait 5 seconds and the probe value will
display again.
To change the SETPOINT:
Push and hold the key for more then 3 seconds to change the value; The value of the SET set point set point will be displayed, and
the “snowflake” LED will start blinking.
To change the SET value:
Push the up or down arrows to the desired setting; the new setting will be memorized after 15 seconds, provided no other
keys are pushed.
Note: The minimum and maximum range of your thermostat is preset and locked by us; so it cannot easily be accidentally moved
between freezer and refrigerator temperatures. To reset this range lock, either call us or find information on our website under
troubleshooting.
melting snowflake snowflake
Up & Down arrows
Felix Storch, Inc.
SUMMIT APPLIANCE DIV.
Page 9
IF YOUR MODEL HAS A FRONT LOCK (SELECTED MODELS)
Your lock has a feature called automatic key eject. To lock or unlock the appliance, you must push and hold the key in the lock
while turning. The lock is spring loaded, so the key cannot be left in the lock.
If the key is lost, contact your dealer or SUMMIT APPLIANCE to purchase a replacement. Always give the model and serial
number of your appliance when requesting a replacement key. Keys for most models can be ordered online at
www.summitapplianceparts.com
NEVER KEEP KEYS WITHIN THE REACH OF CHILDREN
KEYPAD LOCK (optional on most models)
Factory set default password: The factory set default password is 0123. If the default password is lost,
press the key (located inside the battery box) for 30 seconds then wait for the warning sound which
signifies the factory set default password has been restored.
To set the password: While door is open press the key (located inside the battery box) until it jingles,
enter the 0123 password then # within 10 seconds to confirm. Enter the password (1-16 digits) then press #
again to confirm. A total of 10 passwords can be set. Note: each password starts from the number 0 to 9 in order. The first
password starting with 0 is the default password. For example, use 1xxx, then 2xxx etc. for 10 users.
Changing password: While the door is open, press the key (located inside the battery box) until it jingles, enter the old
password and press # within 10 seconds to confirm. Enter new password then press # to confirm. Note: the first digit cannot be
changed.
To open the door: While the door is closed, press the key, enter the password then press again to confirm.
To lock door manually: Press #.
Function setting of automatic lock: To set the auto-lock to lock on a preset time interval press the key (inside the battery
box); enter a number (the time interval in seconds from 10-99) then press # to confirm. The auto-lock time can be set between
10-99 seconds after opening the door. If the time is set less than 10 seconds, the door will not lock automatically, only manually.
Deleting the door-opening passwords: Press the key, enter default password followed by 0000, then press # and all the
door-opening passwords will be deleted except for the default password.
Note: To access the battery box you need to remove only the two small screws, on the top and bottom of that cover. Do not
remove the 4 screws holding the keypad and cover to the appliance door.
Felix Storch, Inc.
SUMMIT APPLIANCE DIV.
Page 10
ALARM INSTRUCTIONS (alarms are optional on most models)
SETTING THE HIGH/LOW ALARM
1. Press the MODE button until unit is in the ALARM DISPLAY MODE indicated by the display of
current temperature and HI and LO alarm settings.
2. To set the HIGH temperature alarm limit press the HI button, to advance the display in 1° incre-
ments, until the desired high temperature is displayed. Press and hold the HI button to rapidly ad-
vance the display in 5° increments.
3. To set the LOW temperature alarm limit press the LO button, to advance the display in 1° incre-
ments, until the desired low temperature is displayed. Press and hold the LO button to rapidly ad-
vance the display in 5° increments.
ALARM
The unit will sound the alarm in both NORMAL DISPLAY MODE and ALARM DISPLAY MODE
DISPLAY MODE. Slide the ALARM ON/OFF switch to ON. When the current temperature display rises above the HI set point, or falls
below the LO set point, the alarm will sound for 1 minute and issue a 3 second repeater beep every minute thereafter, for up to 12 hours.
The alarm will continue to sound even if the current temperature display returns to an “in range” condition.
To temporarily silence the alarm press either the HI or LO button on the back of the unit. The unit is still active and the alarm will sound
again if the temperature goes out of range. To permanently silence the alarm, slide the ALARM ON/OFF switch to OFF position.
OPERATION MODES
SUMMIT alarms have two operating modes: NORMAL AND DISPLAY
DISPLAY MODE and ALARM DISPLAY MODE. To change from one mode to another press the MODE button once.
NORMAL DISPLAY MODE - is indicated by the display of current temperature and the MIN (minimum) and MAX (maximum) tempera-
tures. These temperatures relate to external (probe) temperature if the probe is plugged in, and to ambient temperature if the sensor
probe is removed.
ALARM DISPLAY MODE - is indicated by the display of current temperature and the HI and LO alarm settings. These temperatures re-
late to external (probe) temperature if the probe is plugged in, and to ambient temperature if the sensor probe is removed.
RESETTING THE UNIT
Use a pointed object to push the RESET button on the back of the unit. It is necessary enever a change is m to reset the unit wh ade to
°C/°F temperature, FAST/NORMAL sampling rate, or the probe sensor is plugged in or removed.
NOTE: HI/LO temperature alarm settings and MIN/MAX memories will be cleared after resetting the unit.
SELECTING THE SAMPLING RATE
To select normal sampling rate (60 seconds) or fast sampling rate (10 seconds) slide the switch on back of unit to NORMAL or FAST
NOTE: The unit must be reset after changing the sampling rate. Using the NORMAL sampling rate will extend battery life.
RESETTING MIN/MAX MEMORIES
There are two ways to reset the memories:
I. To reset both minimum and maximum memories - press MEMORY CLEAR button. 2. To reset individual minimum and maximum
memories - press either the MIN or MAX button (on back of unit) once to reset the respective memory. The other memory will remain un-
affected. NOTE: You must be in Normal Display Mode to reset the memories.

Termékspecifikációk

Márka: Summit
Kategória: hűtőszekrény
Modell: FF7LBIMED

Szüksége van segítségre?

Ha segítségre van szüksége Summit FF7LBIMED, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók hűtőszekrény Summit

Summit

Summit SPRF34D7 Útmutató

30 Március 2025
Summit

Summit BAR631BK Útmutató

30 Március 2025
Summit

Summit FF6W7BZADA Útmutató

29 Március 2025
Summit

Summit FDRD152PL Útmutató

11 Január 2025
Summit

Summit ASDR2414 Útmutató

11 Január 2025
Summit

Summit SCR1156CSS Útmutató

10 Január 2025
Summit

Summit AccuCold FF511LBISSHH Útmutató

27 December 2024
Summit

Summit FF28L Útmutató

27 December 2024
Summit

Summit FF7LBL Útmutató

27 December 2024
Summit

Summit = SPR626OS2D Útmutató

27 December 2024

Útmutatók hűtőszekrény

Legújabb útmutatók hűtőszekrény

Miele

Miele K 12820 SD ED Útmutató

4 Április 2025
Liebherr

Liebherr Ksl 3130 Útmutató

4 Április 2025
Costway

Costway EP24436US Útmutató

4 Április 2025
Costway

Costway EP22756US Útmutató

4 Április 2025
Privileg

Privileg PCI6600 Útmutató

3 Április 2025
Vintec

Vintec AL-V40BVC Útmutató

3 Április 2025
Liebherr

Liebherr RO 510 Útmutató

3 Április 2025
Lynx

Lynx LN15REF Útmutató

3 Április 2025
Electrolux

Electrolux ERT 15004 W Útmutató

2 Április 2025
Sub-Zero

Sub-Zero DET3650CIIDR Útmutató

2 Április 2025