Használati útmutató StarTech.com PEX4S953LP

StarTech.com nincs kategorizálva PEX4S953LP

Olvassa el alább 📖 a magyar nyelvű használati útmutatót StarTech.com PEX4S953LP (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: October 31, 2019

Product Diagram (PEX4S953 and PEX4S953LP)

Port Function

1Break-out Cable Port • Connect the to connect 4-Port DB9 Break-out Cable

up to 4 Serial Devices

2Stand-os

• Attach the to the Bracket PCI Express Serial Card

• Secure the to the 4-Port DB9 Break-out Cable

Break-out Cable Port

3Bracket • Attach the to the PCI Express Serial Card Computer

4PCI Express Bus

Connector

• Connect the to the PCI Express Serial Card

Computer Motherboard

5Jumpers • Congure the individual power Serial Connector

settings

6LP4 Power Connector • Used to connect an LP4 Power Source

4-Port PCI Express RS232 Serial Card - 16950 UART

Requirements

For the latest requirements please visit:

www.startech.com/PEX4S953 www.startech.com/PEX4S953LP. - or -

• PCIe Slot

• Needle-Nose Pliers

• (Optional) LP4 Power Source

Installation

WARNING!

PCI Express Serial Cards can be severely damaged by static electricity. Make sure

that you are properly grounded before you open the or touch the Computer Case

PCI Express Serial Card Anti-Static Strap . You should wear an when you install

any computer component. If an isn’t available, discharge any Anti-Static Strap

built-up static electricity by touching a large for several Grounded Metal Surface

seconds. Only handle the by its edges and don’t touch PCI Express Serial Card

the gold connectors.

Jumper Conguration

Note: This is specially designed to allow for power output PCI Express Serial Card

from the ninth pin of the for that support power Serial Connector(s) Serial Devices

over serial. conguration is a requirement when connecting Jumper Serial Devices

that require power through a .Serial Connector

The can be moved into one of three dierent positions in order to set the Jumper

power output voltage for the . The default setting for the Serial Connector Jumpers

is , no power. The must be connected after conguring theRI LP4 Power Connector

Jumper 5V 12V Jumper to or of power. To congure the , complete the following:

1. Ensure the isComputer Power O.

2. Locate the for and carefully remove the . Lift the Jumper Port One Jumper Jumper

straight up and o of the .PCI Express Serial Card

Notes: The is located on the right hand side, labeled as on the Jumper Port 1

. Printed Circuit Board

Always hold the by the edges.Card

3. Determine the power setting that is required for .Port One

4. Position the over the set of that correspond with the desired Jumper Pins Serial

Connector Power Setting Jumper. See to determine where the Figure 1 should be

positioned.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

Warranty Information

This product is backed by a lifetime warranty.

For further information on product warranty terms and conditions, please refer to .

www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: fr.startech.com

DE: de.startech.com

ES: es.startech.com

NL: nl.startech.com

IT: it.startech.com

JP: jp.startech.com

StarTech.com Ltd.

45 Artisans Cres

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Rd,

Brackmills

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

2500 Creekside

Parkwy

Lockbourne, Ohio

43137

U.S.A.

5. Remove the corresponding or from an Full-Height Low-Prole Slot Bracket

available . PCIe Slot

6. (Recongure the for Full-Height or Low-Prole installations) PCI Express Serial Card

Remove the two by twisting each one counterclockwise, using Stand-os Needle-

Nose Pliers Bracket Bracket Break-out Cable . Remove the . Slide the new over the

Port Stand-os Bracket. Insert the two through the and tighten by twisting each

one clockwise, using .Needle-Nose Pliers

7. To install the , carefully align the with the selected Card Card’s Bus Connector

PCIe Slot Motherboard. Card Card on the Push the down rmly to ensure the is

properly seated into the . PCIe Slot

8. (Optional - for power output from the ninth pin of the ) Connect Serial Connectors

the from the to the LP4 Power Connector Cable Computer’s Power Supply LP4

Power Connector Port PCI Express Serial Cardon the .

9. Replace the to secure the . Slot Bracket’s Holding Screw Card

10. Replace the and reconnect the . Computer’s Cover Power Cord

11. Insert the into the and secure 4-Port DB9 Break-out Cable Break-out Cable Port

by tightening the integrated .Thumbscrews

12. Download the latest .Drivers

Driver Installation

You can download the latest from the StarTech.com website: Drivers

www.startech.com/PEX4S953 www.startech.com/PEX4S953LP. - or -

Navigate to the to locate the . Follow the instructions included Support Page Drivers

with the . Driver Files

5. Push the straight down and into place.Jumper

Note: Push the all the way into position for proper contact. Jumper

6. Repeat these steps to congure the for , , and Jumpers Port 2 Port 3 Port 4.

Hardware Installation

1. Ensure the is .Computer Power O

2. Unplug the .Computer Power Cord

3. Remove the . Computer Cover

Note: For further information on how to remove the Computer Cover, refer to the

Manual Computer that came with the .

4. Remove the .Slot Bracket’s Holding Screw

Figure 1

Jumper

Termékspecifikációk

Márka:	StarTech.com
Kategória:	nincs kategorizálva
Modell:	PEX4S953LP

Szüksége van segítségre?

Ha segítségre van szüksége StarTech.com PEX4S953LP, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók nincs kategorizálva StarTech.com

StarTech.com MCM110SC2P Útmutató

26 Szeptember 2024

StarTech.com PLATE9M Útmutató

26 Szeptember 2024

StarTech.com RACKCONV1901 Útmutató

26 Szeptember 2024

StarTech.com PLATE9MB Útmutató

26 Szeptember 2024

StarTech.com ET91000LC2 Útmutató

26 Szeptember 2024

StarTech.com ET10GSFP Útmutató

26 Szeptember 2024

StarTech.com MCM1110SFP Útmutató

26 Szeptember 2024

StarTech.com ET91000SFP2 Útmutató

26 Szeptember 2024

StarTech.com ET91000LC Útmutató

26 Szeptember 2024

StarTech.com ET91000LCOAM Útmutató

26 Szeptember 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

Roland SD-20 Útmutató

16 Október 2024

SilverCrest SRG 1300 C3 Útmutató

16 Október 2024

IFM TY0058 Útmutató

16 Október 2024

Thule Kit 186039 Útmutató

16 Október 2024

Blumfeldt Solidflor Útmutató

16 Október 2024

Dimplex QRAD200E Útmutató

16 Október 2024

DAS Audio AX-112-5 Útmutató

16 Október 2024

Ferplast Ergocomfort Freetime Útmutató

16 Október 2024

AEG MECK52 Útmutató

16 Október 2024

Black Diamond BD1121530000ALL1 Útmutató

16 Október 2024