Használati útmutató StarTech.com PCI2S1P2

Olvassa el alább 📖 a magyar nyelvű használati útmutatót StarTech.com PCI2S1P2 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/2
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: March 10, 2021
Product Diagram (PCI2S1P2)
Front View
Port Function
1Parallel Connector Connect to the on the Parallel Pins PCI Card
2Low-Prole Bracket
(Parallel) See Installing the Low-Prole Bracket(s)
3Parallel Port Connect a Parallel Peripheral Device
DB-25 Parallel (Female)
4Low-Prole Brackets
(Serial) See Installing the Low-Prole Bracket(s)
5Serial Ports Connect Serial Peripheral Devices
DB-9 Parallel (Male)
6 PCI Connector Connect the to the in the PCI Card PCI Slot
Computer
Package Contents
PCI Serial Parallel Combo Card x 1
Full-Prole Bracket (Installed) x 1
Low-Prole Brackets (for Serial Ports) x 2
Low-Prole Bracket (for Parallel Port) x 1
Quick-Start Guide x 1
2S1P PCI Serial Parallel Combo Card with 16C550 UART
Requirements
For the latest requirements, please visit:
www.startech.com/PCI2S1P2.
Computer with an available PCI slot (x4/8/16)
Needle-nose Pliers or 3/16 Nut Driver
Hardware Installation
Warning: PCI Cards can be damaged by static electricity. Make sure that the
Installer Computer Case is properly grounded before they open the or touch the PCI
Card. The should wear an when installing any computer Installer Anti-Static Strap
component. If an is not available, discharge any built-up static Anti-Static Strap
electricity by touching a large for several seconds. Only Grounded Metal Surface
handle the by its edges and do not touch the gold connectors. PCI Card
Installing the Low-Prole Bracket(s)
By default the is attached to the . Full-Prole Bracket Serial/Parallel Port(s)
Depending on the system conguration it may be necessary to remove the Full-
Prole Bracket(s) Low-Prole Bracket(s) to replace with the (included).
1. Remove the from both sides of each , using a Hexagonal Standos Port 3/16 Nut
Driver Needle-nose Pliersor a pair of .
2. Remove the and replace with the .Full-Prole Bracket(s) Low-Prole Bracket(s)
3. Install the removed in step 1. Thread the Hexagonal Standos Hexagonal
Standos Threaded Post 3/16 Nut Driver onto each and tighten, using a or a pair
of .Needle-nose Pliers
Installing the Card
1. Turn o the and any that are connected Computer Peripheral Devices
(e.g. printers, external hard drives, etc.).
2. Unplug the from the rear of the and disconnect any Power Cable Computer
Peripheral Devices that are connected.
3. Remove the from the . Cover Computer Case
Note: Consult the documentation that came with the for details about Computer
how to do this safely.
4. Locate an open and remove the corresponding from the PCI Slot Metal Cover Plate
rear of the . In most instances, the is attached Computer Case Metal Cover Plate
to the rear of the with a single . Save this for the next Computer Case Screw Screw
step.
6
3
2
5
4
1
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a lifetime warranty.
For further information on product warranty terms and conditions, please refer to .
www.startech.com/warranty
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
If product has an exposed circuit board, do not touch the product under power.
Mesures de sécuri
Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください
Misure di sicurezza
Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
Software Installation
Driver Installation
This product requires a driver to be installed on the . Download the Host Computer
latest from the StarTech.com website: Drivers
www.startech.com/PCI2S1P2.
Navigate to the tab to locate the . Follow the instructions Drivers/Downloads Drivers
included with the . Driver Files
5. Gently insert the into the open and fasten the to the rear PCI Card PCI Slot Bracket
of the , using the from step 4. Computer Case Screw
6. Locate a second open and remove the corresponding PCI Slot Metal Cover Plate
from the rear of the . In most instances, the is Computer Case Metal Cover Plate
attached to the rear of the with a single . Save this for Computer Case Screw Screw
the next step.
7. Fasten the to the rear of the , using the Bracket (Parallel) Computer Case Screw
from step 6.
8. Place the back onto the . Cover Computer Case
9. Reconnect all of the that were disconnected in step 2.Peripheral Devices
10. Connect a to the on the .Serial Device Serial Port PCI Card
11. Connect a to the on the .SPP/EPP/ECP Peripheral Device Parallel Port PCI Card
12. Reconnect the to the rear of the .Power Cable Computer

Termékspecifikációk

Márka: StarTech.com
Kategória: nincs kategorizálva
Modell: PCI2S1P2

Szüksége van segítségre?

Ha segítségre van szüksége StarTech.com PCI2S1P2, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva StarTech.com

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva