Használati útmutató Sony HDVF-EL30

Sony nincs kategorizálva HDVF-EL30

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Sony HDVF-EL30 (27 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/27
OLED VIEWFINDER
HDVF-EL30
HDVF-EL20
OPERATION MANUAL [English]
1st Edition
Table of Contents
2
Table of Contents
Precautions................................................ 3
Overview .................................................... 4
Functions of Parts and Controls.............. 6
Front panel .................................................7
Indicators on the screen .............................8
Attaching to the Camera........................... 9
Adjusting Focus and Screen.................. 10
Adjusting the Focus .................................10
Adjusting the Screen................................10
Attaching Accessories............................ 11
Attaching the hood
(HDVF-EL30 only) ........................11
Attaching a Microphone ..........................12
About the eye sensor.............................. 12
Switching the eye point .......................... 13
Adjusting the LCD monitor
(HDVF-EL30 only) ........................... 13
Adjusting the angle ..................................13
Adjusting the screen.................................13
Using the LCD monitor as the tally .........13
Using the Focus Assist Function .......... 14
COLOR PEAKING Function ..................14
PEAKING PLUS Function......................14
MAGNIFICATION Function..................16
Using the Menu........................................ 17
Basic Menu Operations............................17
List of Menu Items...................................19
Error Message ......................................... 23
Specifications .......................................... 23
Precautions 3
Precautions
Viewfinder Lenses
Do not leave the viewfinder lens faced toward a strong
light source, such as sunlight.
A concentration of strong light, such as sunlight via the
lens may burn out the OLED panel or cause a fire.
About the OLED panel
The OLED panel fitted to this unit is manufactured with
high precision technology, giving a functioning pixel
ratio of at least 99.99%. Thus a very small proportion of
pixels may be “stuck”, either always off (black), always
on (red, green, or blue), or flashing. In addition, over a
long period of use, because of the physical characteristics
of the organic light-emitting diode, such “stuck” pixels
may appear spontaneously. These problems are not a
malfunction.
These phenomena have no effect on the camera’s output
signals.
Burn-in
Due to the characteristics of the material used in the
OLED panel, permanent burn-in or reduction in
brightness may occur.
These problems are not a malfunction.
When still images are displayed in the same position on
the screen continuously or repeatedly, permanent burn-in
may occur.
Images that may cause burn-in
• Character or message displays that indicate settings or
the operating state
• On-screen displays such as center markers or safety
zones
• Masked images with aspect ratios other than 16:9
• Color bars or images that remain static for a long time
• When the HIGH EYEPOINT function is set to “ON.”
To reduce the risk of burn-in
• Use with the EYE SENSOR setting set to “ON”
This unit has an anti-burn-in function for the OLED
panel.
When your eye is away from the eyecup, an image with
the video signal level reversed may be displayed or the
image may be not displayed.
• Fill the entire screen with images
- Displays the image after switching HIGH
EYEPOINT to “OFF.”
- Turn the mask display of the connected camera to
“OFF” before displaying the image. For details, refer
to the operation manual of the camera.
• Turn off the character and marker displays
Press the MENU switch to turn off the character
displays. To turn off the character or marker displays of
the connected equipment, operate the connected
equipment accordingly. For details, refer to the
operation manual of the connected equipment.
• Turn off the power when not in use
Turn off the power if the viewfinder is not to be used for
a prolonged period of time.
About the LCD panel (HDVF-EL30 only)
• The LCD panel fitted to this unit is manufactured with
high precision technology, giving a functioning pixel
ratio of at least 99.99%. Thus a very small proportion of
pixels may be “stuck”, either always off (black), always
on (red, green, or blue), or flashing. In addition, over a
long period of use, because of the physical
characteristics of the liquid crystal display, such
“stuck” pixels may appear spontaneously. These
problems are not a malfunction.
These phenomena have no effect on the camera’s
output signals.
• Do not leave the screen facing the sun as it can damage
the screen. Take care when you use the unit outdoors.
• Do not push or scratch the screen. Do not place a heavy
object on the screen. This may cause the screen to lose
uniformity.
• An afterimage may appear when a still image is
displayed continuously. Turn the viewfinder off when it
is not used for a long time.
• When using the viewfinder in low temperature, the
moving image resolution deteriorates right after the
viewfinder is turned on.
Handling and maintenance of the screen
The surface of the screen is specially coated to reduce
image reflection. Make sure to observe the following
points as improper maintenance procedures may impair
the screen’s performance. In addition, the screen is
vulnerable to damage. Do not scratch or knock against it
using a hard object.
• Be sure to turn off the power of the connected
equipment before performing maintenance.
• The surface of the screen is specially coated. Do not
attach adhesive objects, such as stickers, on it.
• The surface of the screen is specially coated. Do not
touch the screen directly.
• Wipe the screen surface gently with a soft dry cloth to
remove dirt.
• Stubborn stains may be removed with a soft cloth
slightly dampened with a mild detergent solution.
• The screen may become scratched if a cloth is dusty.
• Never use strong solvents such as alcohol, benzene,
thinner, acidic or alkaline detergent, detergent with
abrasives, or chemical wipe as these may damage the
screen.
Overview
4
• Use a blower to remove dust from the screen surface.
Do not subject the screen to strong
impact
Strong impact on the screen may damage it, such as
deformation of the internal structure or outer appearance.
Electrolytic capacitor
The life expectancy of the electrolytic capacitor is about
5 years under normal operating temperatures and normal
usage (8 hours per day; 25 days per month). If usage
exceeds the above normal usage frequency, the life
expectancy may be reduced correspondingly.
Operation and storage environment
Store the viewfinder in a level and air-conditioned place.
Avoid using or storing in the following places:
• Places that are extremely hot or cold
• Places with a high level of humidity
• Places with strong vibrations
• Places with strong magnetic fields
• Places that are exposed to direct sunlight for long hours
or near a heating device
Dew condensation
If the unit is suddenly taken from a cold to a warm
location, or if ambient temperature suddenly rises,
moisture may form on the outer surface of the unit and/or
inside of the unit. This is known as condensation. If
condensation occurs, turn off the unit and wait until the
condensation clears before operating the unit. Operating
the unit while condensation is present may damage the
unit.
Disposal of the unit
Do not dispose of the unit with general waste.
Do not include the unit with household waste.
When you dispose of the unit, you must obey the law in
the relative area or country.
Overview
The HDVF-EL30/HDVF-EL20 OLED Viewfinder is a
color viewfinder for use with a Sony high-definition color
camera.
This viewfinder has the following features.
Advantages of OLED panel technology
The OLED panel makes use of an organic material, which
emits light when an electric current is applied. Being self-
emitting, the strength of luminescence can be controlled
by the amount of electric current. This brings about the
following three features:
Quick motion picture response:
The luminescent state of the OLED panel can be changed
instantaneously by changing the current flow in the
organic material. This enables a quick motion picture
response and production of images with minimal blurring
and ghosting. Furthermore, performance for shooting on
location is not influenced by changes in environmental
temperature.
High contrast and wide dynamic range:
The OLED panel does not emit light when black signal is
applied to the viewfinder, enabling a pure black screen to
be displayed. Furthermore, thanks to high peak brightness
the panel impressively displays brilliance and clarity of
various sparkling images, such as stars in a night sky
twinkling, night illuminations winking or glass glittering,
etc.
Rich color reproduction:
An OLED panel’s self-luminescence also allows for great
color reproduction across the entire spectrum in
practically any shade or brightness.
Focus Assist function
This viewfinder comes with an original Focus Assist
function to support accurate focusing.
• Peaking function
Edge enhancement can be performed in the horizontal/
vertical direction on the entire of the screen. Coloring
the edge enhancement part can improve visibility.
• Peaking Plus function
Edge enhancement can be performed on the object that
is specified using a color, area selected, or both.
• Image magnification (FOCUS MAG) function
Displays a part of the image expanded to twice the size.
You can adjust the focus easily.
To switch to preset adjustment settings
Brightness and contrast can be preset for selection
through an assignable switch or a menu operation.
Overview 5
Assignable switch
Two assignable switches are provided for the storage of
frequently used functions.
Tally lamps
The viewfinder comes with three tally lamps (red, green,
and yellow), which light up in response to tally signals.
Check the connected camera to identify whether the use
of the yellow tally lamp is supported.
You can use the LCD screen as an up-tally. (HDVF-EL30
only)
High-performance loupe
The 4-group 7-element lens (including aspheric lens)
delivers pictures with low distortion and allows
adjustment over a wide range of visibility.
If the optional close-up lens (ø37) is mounted, you can
shift the visibility ratio to the far-sighted side.
Hood for the LCD panel (HDVF-EL30 only)
A small, light hood for the LCD panel is supplied. This is
useful when recording.
Functions of Parts and Controls
6
Functions of Parts and Controls
HDVF-EL30
HDVF-EL20
Viewfinder cable
Viewfinder cable
Front panel
(page 7)
Front panel
(page 7)
Microphone
holder LCD (HDVF-EL30 only)
Microphone
holder
Functions of Parts and Controls 7
a Plug
Connect to the VF connector on the camera.
b Stopper
Prevents the viewfinder from coming off the camera
when it is slid from side to side.
c Tally indicator (front)
Lights up when the camera receives the red tally signal.
The brightness can be adjusted with the TALLY switch
on the front panel. Set the TALLY switch to OFF when
not in use.
d MENU control
Turn the control to select a menu item, and then press the
control to confirm the selection. Use with the MENU
switch to set various functions.
When the menu is not displayed, pressing this control
shows the status information of the viewfinder on the
screen.
For details on operations, see “Using the Menu” on page
17.
e Tally indicator (rear)
Lights up when the camera receives the red tally signal.
This indicator can be covered when not in use.
f Eyecup
Blocks external light while you are shooting.
Over time the eyecup may become cracked. If this occurs,
it should be exchanged.
g Eye sensor
Controls the anti-burn-in function for the OLED panel.
• Do not cover or block the eye sensor.
• To prevent screen burn-in on the OLED panel, the
video signal level in the display may be inverted or the
image may not be displayed when your eye is not in
contact with the eyecup.
h Diopter adjustment ring
Turn this until the image is sharpest for your eyesight.
i ASSIGN (assignable) 1/2 switches
Can be used to store frequently used functions.
Storing a function is performed using “ASSIGN 1” or
“ASSIGN 2” in the FUNCTION menu (page 19).
j MENU switch
Displays the menu. Use with the MENU control to set
various functions.
When the menu is not displayed and this switch is pressed
and held for three seconds or more, “VR LOCK” appears.
This locks the BRIGHT, CONTRAST, and PEAKING
controls at their current settings, preventing accidental
operation. To unlock the controls, press this switch for
three seconds or more again so that “VR UNLOCK”
appears.
For details on operations, see “Using the Menu” on page
17.
Front panel
a PEAKING control
Sharpens the edges in the picture. This control has no
effect on the camera’s video output signals. Turning the
control clockwise increases the sharpness.
b CONTRAST control
Adjusts the picture contrast. This control has no effect on
the camera’s video output signals. Turning the control
clockwise increases the contrast.
HDVF-EL20
This control is disabled when “PRESET” in the PRESET
menu (page 21) is set to “ON.”
HDVF-EL30
This control is disable when “PRESET” is set to “ON”
and “PRESET SELECT” is set to “BOTH” in the
PRESET menu (page 21).
c BRIGHT (brightness) control
Adjusts the picture brightness. This control has no effect
on the camera’s video output signals. Turning the control
clockwise increases the brightness.
HDVF-EL20
This control is disabled when “PRESET” in the PRESET
menu (page 21) is set to “ON.”
HDVF-EL30
This control is disable when “PRESET” is set to “ON”
and “PRESET SELECT” is set to “BOTH” in the
PRESET menu (page 21).
Notes
Attaching to the Camera 9
Attaching to the Camera
When the viewfinder is attached, do not leave the camera
with the eyepiece facing the sun. Direct sunlight can enter
through the eyepiece and be focused in the viewfinder,
which may cause the OLED panel to burn out or cause a
fire.
1 Loosen the left-right positioning ring on the camera.
2 Insert the slide guide which is located on the front of
the camera into the slide rail which is located on the
back of the viewfinder.
3 Slide the viewfinder in the direction of the arrow.
4 Position the viewfinder by sliding it from side to
side, and tighten the left-right positioning ring on the
camera.
5 Connect the plug to the VF connector on the camera.
Always check to be sure that the plug is firmly inserted
into the camera’s VF connector.
To detach the viewfinder
To detach the viewfinder from the camera, conduct the
attachment procedure in reverse. When removing the
viewfinder from the camera, pull up the stopper.
Note about loading in carrying case
When loading the camera with viewfinder attached into a
carrying case, make sure that the camera and the
viewfinder fit into the case without having to be forced.
Applying undue pressure can result in damage to the
camera or viewfinder.
Note
Stopper
Left-right
positioning
ring
Slide rail
Slide guide
Plug
VF connector
Note
Adjusting Focus and Screen
10
Adjusting Focus and
Screen
Adjusting the Focus
Turn the diopter adjustment ring until the image is
sharpest for your eyesight.
To shift the visibility ratio to the far-
sighted side
Mount the optional close-up lens (ø37) to the thread
groove of the loupe.
Adjusting the Screen
For details on the menu operation, see “Using the Menu”
on page 17.
1 Set “PRESET” in the PRESET menu (page 21) to
“OFF.”
2 Turn the BRIGHT control to adjust the brightness of
the screen.
To make the picture brighter: Turn the control
clockwise.
3 Turn the CONTRAST control to adjust the screen
contrast.
To increase the contrast: Turn the control
clockwise.
4 Turn the PEAKING control to adjust edges in the
image.
To make edges in the image sharper: Turn the
control clockwise.
5 Set “CHROMA” in the FUNCTION menu (page 19)
to adjust the chroma level.
To adjust the OLED and LCD screen
separately (HDVF-EL30 only)
1 Set “PRESET” in the PRESET menu (page 21) to
“ON.”
2 Set “PRESET SELECT” in the PRESET menu to
“OLED” or “LCD.”
3 Adjust the brightness of the screen.
If “PRESET SELECT” is not set, turn the BRIGHT
control to adjust the picture brightness.
To make the picture brighter: Turn the control
clockwise.
If “PRESET SELECT” is set, set “PRST BRIGHT”
in the PRESET menu to adjust the picture brightness.
To make the picture brighter: Raise the setting
value.
4 Adjust the screen contrast.
If “PRESET SELECT” is not set, turn the
CONTRAST control to adjust the screen contrast.
To increase the contrast: Turn the control
clockwise.
If “PRESET SELECT” is set, set “PRST
CONTRAST” in the PRESET menu to adjust the
screen contrast.
To increase the contrast: Raise the setting value.
Thread groove
Diopter adjustment ring
Attaching Accessories 11
5 Turn the PEAKING control to adjust edges in the
image.
To make edges in the image sharper: Turn the
control clockwise.
6 Set “CHROMA” in the FUNCTION menu (page 19)
to adjust the chroma level.
Make sure the setting of “PRESET” in the PRESET menu
before performing the procedure above.
Depending on the setting, the BRIGHT and CONTRAST
controls may not be operated.
Attaching Accessories
Attaching the hood (HDVF-EL30
only)
1 Attach the hood inserting its claws in the left and
right grooves of the LCD monitor.
The hood can also be rotated up and down 180
degrees and attached.
By collapsing the hood while it is attached to the LCD
monitor, you can use it as the protection cover of the LCD
monitor.
When you retract the LCD monitor with the hood
attached, rotate the LCD monitor to the opposite side by
180 degrees so that the hood faces up.
When you retract the LCD monitor forcibly with the hood
attached, it may cause a malfunction or damage.
Note
Note
Hood
About the eye sensor
12
Attaching a Microphone
1 Loosen the screw of the microphone holder and open
the holder.
2 Attach the microphone to the microphone holder,
then close the holder and tighten the screw.
When necessary to use a slender microphone, attach
a microphone spacer (supplied with the microphone)
to the microphone beforehand.
3 Insert the microphone plug into the MIC connector
on the camera, or the MIC IN connector on the
camera adaptor.
When connecting the microphone to the camera
adaptor, you will need to set the microphone
selector.
For details, see the manual supplied with your camera
adaptor.
About the eye sensor
Controls the anti-burn-in function of the OLED panel.
For details on the menu operation, see “Using the Menu”
on page 17.
1 Set “EYE SENSOR” in the OLED menu to “ON.”
• Use with the EYE SENSOR setting set to “ON.” When
used with the setting set to “OFF,” permanent burn-in
may occur.
• Do not cover or block the eye sensor.
• To prevent screen burn-in on the OLED panel, the
video signal level in the display may be inverted or the
image may not be displayed when your eye is not in
contact with the eyecup.
Hood
Notes
Switching the eye point / Adjusting the LCD monitor (HDVF-EL30 only) 13
Switching the eye point
When your eye is away from the eyecup while recording,
set the HIGH EYEPOINT function to “ON.” The
effective screen is displayed with a reduced display and
you can see the whole screen easily.
1 Switch the eye point by pressing the ASSIGN switch
assigned with the HIGH EYEPOINT function.
You can set this in “HIGH EYEPOINT” of the
OLED menu (page 21).
• When the HIGH EYEPOINT function is set to “ON,”
the resolution of the effective screen decreases.
• When the HIGH EYEPOINT function is set to “ON”
and used for extended periods, burn-in may occur.
Adjusting the LCD
monitor (HDVF-EL30
only)
When you open the LCD monitor, it turns on. When you
retract it with the screen side facing down, it turns off.
Adjusting the angle
You can rotate the LCD monitor to the opposite direction
by 180 degrees (the direction in which the monitor faces
an object) and to the other direction by 90 degrees.
When you rotate the monitor to the opposite direction by
180 degrees, the image is flipped horizontally (mirror
image).
When you retract the monitor with it rotated to the
opposite direction by 180 degrees, the image is flipped
horizontally and vertically.
The image flip can be set manually by setting “MIRROR”
to “MANUAL” in the LCD menu (page 22).
Adjusting the screen
For details on adjusting the screen, see “Adjusting the
screen” (page 10).
Using the LCD monitor as the tally
You can use the LCD monitor as the tally.
For details on the menu operation, see “Using the Menu”
on page 17.
1 Select “TALLY” in “DISPLAY MODE” in the LCD
menu.
2 Set “CAMERA NUMBER” in the LCD menu.
Notes
Normal
When HIGH EYEPOINT is set to “ON”
90°
1 0°8
Using the Focus Assist Function
14
When “CAMERA LINK” is set to “ON” in the LCD
menu, the same number as the camera number is set as
CAMERA NUMBER.
This function is not compatible depending on the
connected camera.
For details of compatible models, contact your Sony
service representative.
3 Set the brightness in “TALLY DIM” in the LCD
menu.
4 By rotating the LCD monitor by 180 degrees to the
opposite positon, the screen is switched to the tally.
Using the Focus Assist
Function
For details on menu operations, see “Using the Menu”
on page 17.
COLOR PEAKING Function
When the COLOR PEAKING function is set to “ON,” the
peaking signal is displayed with the colors changed.
1 Set “COLOR PEAKING” to “ON” in the PEAKING
menu.
2 Select the displaying color with “COLOR” in the
PEAKING menu.
3 Adjust the chroma level of the video signal with
“CHROMA” in the PEAKING menu.
When “ORIG” is selected in “COLOR,” the video
signal is displayed in monochrome. The chroma
level of the video signal cannot be adjusted.
Color peaking is a function that extracts the high-
frequency components of the video signal and applies
color to those parts. This may be less effective when noise
components are emphasized by VF DETAIL and
MASTER GAIN settings on the camera side, because
then color is applied to the whole screen.
If you plan to use the color peaking function, it is
recommended that the VF DETAIL and MASTER GAIN
settings on the camera side be set as follows.
• VF DETAIL: OFF, or set to a value that does not
emphasize noise.
• MASTER GAIN: Set to a value near 0 dB.
PEAKING PLUS Function
This function can be used to sharpen the edges of an
image that is specified using the color, area selected, or
both. You can also enhance the edges of the entire image.
This function has no effect on the camera’s video output
signals.
To sharpen edges by specifying the color
1 Press the ASSIGN switch that is assigned the
PEAKING PLUS function to switch to the
PEAKING PLUS mode.
The PEAKING PLUS indicator lights up.
Note
Note
Using the Focus Assist Function 15
You can also set to this mode using “PEAKING
MODE” from the PEAKING PLUS menu (see page
20).
2 Select “COLOR” under “COLOR/AREA SEL” of
the PEAKING PLUS menu.
3 Press and hold the ASSIGN switch that is assigned
the PEAKING PLUS function for one second or
more (the detection area marker appears in the center
of the screen), align the color to be corrected in the
detection area marker, and then release the switch.
The color that is to be corrected will be detected.
: Effective edge enhancement area
4 Adjust the effective edge enhancement area of the
color using the following menus in the PEAKING
PLUS menu.
• HUE PHASE: Hue center position
• HUE WIDTH: Hue range
• SAT WIDTH: Saturation range
– direction:
Narrows the effective range
+ direction:
Widens the effective range
5 Adjust the amount of correction with the PEAKING
control.
Only the edges of the object that coincides with the
color detected in step 3 will be sharpened.
Turn the control clockwise to make the edges
sharper.
To sharpen edges by specifying the
display area
1 Press the ASSIGN switch that is assigned the
PEAKING PLUS function to switch to the
PEAKING PLUS mode.
The PEAKING PLUS indicator lights up.
You can also set to this mode using “PEAKING
MODE” from the PEAKING PLUS menu (see page
20).
2 Select “AREA” under “COLOR/AREA SEL” of the
PEAKING PLUS menu.
3 Select an area under “POSITION” of the PEAKING
PLUS menu.
: Effective edge enhancement area
If the “POSITION” setting is changed, the “MAG
POSITION” setting in the MAGNIFICATION menu
will be changed too.
4 Adjust the amount of correction with the PEAKING
control.
Only the edges of the object within the area selected
in step 3 will be sharpened.
Turn the control clockwise to make the edges
sharper.
To specify both color and area
1 Press the ASSIGN switch that is assigned the
PEAKING PLUS function to switch to the
PEAKING PLUS mode.
The PEAKING PLUS indicator lights up.
You can also set to this mode using “PEAKING
MODE” from the PEAKING PLUS menu (see page
20).
2 Select “BOTH” under “COLOR/AREA SEL” of the
PEAKING PLUS menu.
3 Select an area under “POSITION” of the PEAKING
PLUS menu.
Detection
area
marker
CENTER UPPER LOWERRIGHT LEFT
CENTER UPPER LOWERRIGHT LEFT
Using the Focus Assist Function
16
If the “POSITION” setting is changed, the “MAG
POSITION” setting in the MAGNIFICATION menu
will be changed too.
4 Press and hold the ASSIGN switch that is assigned
the PEAKING PLUS function for one second or
more (the detection area marker appears in the center
of the screen), align the color to be corrected in the
detection area marker, and then release the switch.
The color that is to be corrected will be detected.
: Effective edge enhancement area
5 Adjust the effective edge enhancement area of the
color using the following menus in the PEAKING
PLUS menu.
• HUE PHASE: Hue center position
• HUE WIDTH: Hue range
• SAT WIDTH: Saturation range
6 Adjust the amount of correction with the PEAKING
control.
The edges of the object that coincides with the color
detected in step 4 are sharpened within the area
selected in step 3.
Turn the control clockwise to make the edges
sharper.
To enhance the edges of the entire image
1 Press the ASSIGN switch that is assigned the
PEAKING PLUS function to switch to the STD
(standard) mode.
The PEAKING PLUS indicator is turned off.
You can also set to this mode using “PEAKING
MODE” from the PEAKING PLUS menu (see page
20).
2 Adjust the amount of correction with the PEAKING
control.
Turn the control clockwise to make the edges
sharper.
MAGNIFICATION Function
This function enables you to adjust the focus easily by
enlarging the image vertically and horizontally to two
times the size.
For enlarging the image, press the ASSIGN switch
assigned with the MAGNIFICATION function. Every
press switches between the normal display and enlarged
display.
To select the enlarged display part
You can select one of the following as the enlarged
display part; center of the monitor (factory setting),
upper, right, lower, left.
1 Press and hold the ASSIGN switch assigned with the
MAGNIFICATION function for about one second.
The camera enters to the enlarged display part
selecting mode, and the MAG indicator and MAG
position indicator (page 8) are displayed.
At the same time the screen is switched to the
enlarged display.
2 Press and hold the ASSIGN switch assigned with the
MAGNIFICATION function. When the MAG
position indicator shows your favorite position,
release the switch.
The camera switches the enlarged part in the
following order;
While pressing and holding the switch the enlarged
display is kept. The enlarged display switches among
upper, right, lower, left and center about every
second.
If the “MAG POSITION” setting is changed, the
“POSITION” setting in the PEAKING PLUS menu
(page 20) also changes.
You can set the enlarged display in the
MAGNIFICATION menu (page 21).
To return to normal display
The two manners of returning to the normal display,
under “AUTO RELEASE” settings in the
MAGNIFICATION menu (page 21), are as follows.
“AUTO”: Returns to the normal display automatically in
a specified time after magnifying the image using the
ASSIGN switch.
“MANUAL”: Press the ASSIGN switch again to return
to the normal display.
CENTER UPPER LOWERRIGHT LEFT
Using the Menu 17
Using the Menu
Many of the viewfinder’s functions can be set by a menu
operation.
Basic Menu Operations
1 Enter the menu.
Press the MENU switch.
A menu page appears in the viewfinder display.
Example
The viewfinder menu can be displayed at the same
time a picture from the camera is being displayed.
The camera picture or menu darkens so that it
appears dimly behind the viewfinder menu.
2 Select a menu page.
While the ? mark appears to the left of the page
number (page select mode), turn the MENU control.
The menu changes to another page.
When the desired menu page appears, press the
MENU control.
The
c mark appears to the left of a menu item on the
selected menu page (item select mode).
• To select another menu page, press the MENU
switch to return to the page select mode.
• If the ? mark appears to the left of the setting (value
setting mode), press the MENU switch to change
to item select mode. Press the MENU switch again
to change to page select mode.
3 Select menu items.
With the
c mark positioned to the left of a menu item
on the selected menu page (item select mode), turn
the MENU control to move the c mark to the desired
menu item.
To move the c mark downward, turn the control
clockwise. To move the c mark upward, turn the
control counterclockwise.
Position the c mark to the left of the desired menu
item, and then press the MENU control.
A ? mark appears to the left of the setting and the
settings screen is activated (value setting mode).
To select another menu item, press the MENU
switch to return to item select mode.
4 Change the value of a setting.
With the ? mark positioned to the left of the setting
(value setting mode), turn the MENU control to
change the value.
If the setting is a numerical value, turn the MENU
control clockwise to increase the value, and
counterclockwise to decrease the value.
Turning the control quickly changes the value
rapidly, and turning it slowly allows you to make
fine adjustments.
5 Enter the setting.
Press the MENU control.
M E N UV
?
K N EE M O N C H R O M EO
:
:
AS S I G N .
. 1
AS S I G N 2
:
:
:
:
OM N O
M A G
P E A I N G P L U S S
WK EDOM 1
C H R M AO 0
FO F
FO F
0 1 F U N C T I O N
F
O N
O ND DI MD IN
:
:
:
YT L LA O RN II A TC
Y /T L LA
DI NY /T L LA
DL EO
0?
5
:C D L 5
2M E N UV F
? mark
cO N
O ND DI MD IN
:
:
:
YT L LA O RN II A TC
Y /T L LA
DI NY /T L LA
DL EO
0
5
:C D L 5
2M E N UV F
c mark
? O N
O ND DI MD IN
:
:
:
YT L LA O RN II A TC
Y /T L LA
DI NY /T L LA
DL EO
0
5
:C D L 5
2M E N UV F
Value setting mode

Termékspecifikációk

Márka: Sony
Kategória: nincs kategorizálva
Modell: HDVF-EL30

Szüksége van segítségre?

Ha segítségre van szüksége Sony HDVF-EL30, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók nincs kategorizálva Sony

Sony

Sony Clié PEGA-UC60K Útmutató

13 Január 2025
Sony

Sony SU-WB1 Útmutató

12 Január 2025
Sony

Sony MKS-6550 Útmutató

11 Január 2025
Sony

Sony MSAC-HGA8 Útmutató

23 December 2024
Sony

Sony CKS-NWS610 Útmutató

23 December 2024
Sony

Sony CKM-NWE010 Útmutató

23 December 2024
Sony

Sony CLP-NWU30 Útmutató

23 December 2024
Sony

Sony LCM-CSVH Útmutató

23 December 2024
Sony

Sony LCS-VCC Útmutató

23 December 2024
Sony

Sony ACC-V1BP Útmutató

17 December 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

AEG

AEG AirFry A9OOAFWM Útmutató

1 Április 2025
Atlona

Atlona AT-HDR-EX-70C-TX Útmutató

1 Április 2025
Parallels

Parallels Plesk Panel 11.5 Útmutató

1 Április 2025
Sunny

Sunny Fresh Art Easel Útmutató

1 Április 2025
Crestron

Crestron CAEN-1X1 Útmutató

1 Április 2025
Crestron

Crestron CAEN-4X2 Útmutató

1 Április 2025
Hamlet

Hamlet HXD25TCU31 Útmutató

1 Április 2025
Crestron

Crestron CAEN-7X1 Útmutató

1 Április 2025
Crestron

Crestron CAEN-7X2 Útmutató

1 Április 2025
Crestron

Crestron CAEN-2X1 Útmutató

1 Április 2025