Használati útmutató Sonance Visual Performance VP69

Sonance hangszóró Visual Performance VP69

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Sonance Visual Performance VP69 (4 oldal) a hangszóró kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/4
Introduction
Thank you for purchasing Sonance Visual Performance®
Series Medium rectangle speakers. When properly installed your
new speakers will give you years of entertainment pleasure.
Box Contents
Each Sonance Visual Performance Series Medium rectangle
speaker box contains (2) Visual Performance Series speakers,
(2) paint plugs (installed on the fronts of the speakers),
(2) paintable grilles and (1) mounting cut-out template.
Speaker Placement
Home Theater Speaker Placement
Left, Center & Right Speakers
• Place the left & right speakers on either side of the video
screen, 6 – 10 feet (1.8m – 3m) apart and 3 – 4 feet
(0.9m – 1.2m) from the floor.
• If possible, locate the center speaker at the same height as the
left & right channel speakers.
• If you must place the center speaker above or below a video
screen, place it no more than 2 feet (0.6m) above or below the
center of the left and right speakers. This will maintain consis-
tent tonality between all three front channel speakers.
• The main listening position should be 8 – 12 feet
(2.4m – 3.7m) away from the speakers.
Use
Figure 1
as a guide.
Surround Speakers (5.1-Channel System)
Locate the surround channel speakers on the side walls 2 – 6 feet
(0.6m – 1.8m) behind the listening position, 5 – 7 feet
(1.5m – 2.1m) from the floor. Use
Figure 2
as a guide.
Surround Speakers (7.1-Channel System)
• LEFT & R : Place the left and right IGHT SURROUND PEAKERSS
surround speakers directly to the sides of the listening position,
at least 5 feet from the floor.
• SURROUND PEAKERSBACK S : Place the surround back speakers in
the rear wall, 3 – 6 feet (0.9m – 1.8m) apart and 5 – 7 feet
(1.5m – 2.1m) from the floor.
Use
Figure 3
as a guide.
I N S T R U C T I O N M A N U A L
V I S U A L P E R F O R M A N C E ® S E R I E S
M E D I U M R E CTA NGL E S P E A K E R S
S W :AFETY ARNING
THESE SPEAKERS HAVE AST OUNTF M ®TABS T HAT PREVENT T HE
SPEAKER FROM FALLING OUT OF THE MOUNT ING HOLE DURING THE
INSTALLATION PROCESS.
T F MH E E DG E S O F T H E A S T O U NT TA B S A R E V E RY S H A R P.
US E CA U T I ON W HE N H A ND L I N G T H E S P E A K E R.
18"
(0.5m)
From Side
Wall
18"
(0.5m)
From Side
Wall
2'
(0.6m)
max.
6' – 10'
(1.8m – 3m)
Apart
FIGURE 1: LEFT, C & RENTER IGHT HANNELC
H TOME HEATER PEAKER LACEMENTS P
5' – 7'
(1.5m – 2.1m)
2' – 6'
(0.6m – 1.8m)
F H T S SIGURE 2: 5.1-CHANNEL OME HEATER URROUND PEAKER
PLACEMENT
Right Surround
Speaker
Left Surround
Speaker
Left
Front
Speaker
Right
Front
Speaker
Video
Screen
Center
Speaker
Left
Surround Back
Speaker
Right
Surround Back
Speaker
F H T S PIGURE 3: 7.1-CHANNEL OME HEATER PEAKER LACEMENT
2
SONANCE VISUAL PERFORMANCE®MEDIUM RECTANGLE
Stereo (2-Channel) Placement
• Place the left and right speakers 6 – 10 feet (1.8m – 3m) apart,
with the main listening position as close to midway between
the speakers as possible.
• The speakers should be at least 2 feet (0.6m) away from the
side walls.
• The main listening position should be 4 – 10 feet (1.2m – 3m)
away from the speakers.
• In most cases pivoting the tweeter of each speaker directly
towards the main listening position will help maximize the
stereo soundstage.
Use the left and right speaker placement in
Figure 1
, on page 1,
as a guide.
Before Installation: Retrofit
1. Determine the location for the speaker (see
Speaker Placement
on page 1).
2. Perform an obstruction survey to be certain that there are no
studs, conduit, pipes, heating ducts, pocket doors or air returns
in the wall cavity that will interfere with the speaker.
3. Mounting space requirements:
Mounting space req uirements:
Mounting space req uirements:
Mounting space req uirements:Mounting space req uirements: 615⁄16” (176mm) wide by
10¾” (273mm) high cut-out and at least 3½” (89mm) mount-
ing depth. Medium ThinLine rectangle speakers require at
least 2½” (64mm) mounting depth.
4. Position the included cut-out template where the speaker is to
be located and pencil an outline on the wall. If you are unsure
about obstructions, drill a small hole in the center of the
outline and insert a coat hanger wire into the hole to feel-
around for possible obstructions.
5. Cut the mounting hole using a keyhole or drywall saw, and
run the speaker wires from the mounting hole to the amplifier
location.
NOT E : CO NSU LT LOC AL B U IL DI NG C OD E S B E FOR E R U N NI NG
SP E AK E R W IR E S TH ROU G H W AL LS.
Before Installation: IR Plug
Sonance Visual Performance Series
Medium rectangle speakers have a
plug for installing an IR receiver into
the speaker’s front baffle (see
Figure
4
). In systems where the electronics
are placed in an inconvenient loca-
tion this allows remote controls to be
aimed at the front of the room instead
of at the electronics.
The IR plug is in the form of a bolt
and retaining nut. To remove the
plug, unscrew the nut (located behind
the baffle, see
Figure 5
) and remove
the bolt. The hole is designed to
receive a Sonance OptiLinQ®SMR1
or SMR1P Surface-Mount IR receiver.
Insert the IR receiver through the
front of the speaker baffle and use
the nut included with the receiver to
secure it to the baffle.
Installation
Sonance Visual Performance Series speakers feature exclusive
FastMount tabs and an integral Roto-Lock®mounting system for
quick mounting directly into existing walls.
WA R N I NG : T HE E D GE S O F T HE FA S T M OU N T TA B S
ARE VERY SHARP. USE CAUTION WHEN HANDLING
T HE S P E A K E R.
1. Remove the paint plug from the speaker.
2. Strip ¼” – ½” (6mm – 12mm) of insulation from each speak-
er lead. Twist the strands or tin the exposed wire with solder
to ensure that there are no stray strands. (Stray strands that
touch each other can cause a short-circuit that can damage
the amplifier.)
3. The speaker’s connector posts are spring-loaded. Push the top
of each connector post down to open the connector and insert
the exposed wires into the holes in the posts.
The speaker’s positive
post is labeled with a
red dot; the negative
post is labeled with a
black dot. Double-check
that you connected
amplifier “+” to speaker
“+” and amplifier “–” to
speaker “–”.
4. Make sure all the Roto-
Lock clamps are retract-
ed so that they are
tucked within the mount-
ing hole’s border. Insert
the speaker into the hole
in the wall (
Figure 6
).
The Roto-Lock system
can accommodate a
maximum wall material
thickness of 1¼”
(32mm).
The FastMount tabs will
prevent the speaker from
falling out of the mount-
ing hole, allowing you to
let go of the speaker to
pick-up tools or other
items (
Figure 7
).
N FOTE: THE ASTMOUNT TABS
ARE DESIGNE D F OR ONE -
TI M E U S E ON LY. IF THE
SPEAKE R IS R EM OVE D FR OM
TH E MO U NTI NG H OL E TH E
F MA S T O U N T TA B S W I L L
DISCON NE CT A ND REM AIN
IN SIDE THE WALL.
Roto-Lock Clamp
(retracted)
Roto-Lock Clamp
(retracted)
F SIGURE 6: INSERTING THE PEAKER
INTO THE OUNTING OLEM H
FastMount
Tabs
Roto-Lock Clamps
(retracted)
FIGURE 7: FAST OUNTM TABS AND
R -L COTO OCK LAMPS
FIGURE 4: IR PLUG
FIGURE 5: IR PLUG
RETAINING UTN
IR Plug
Retaining Nut
3
SONANCE VISUAL PERFORMANCE®MEDIUM RECTANGLE
5. Tighten the four screws
on the front of the speaker
baffle. The RotoLock
clamps will automatically
rotate into position and
begin clamping the
speaker (
Figure 8
).
When you notice resist-
ance on the screws the
speaker has been
clamped successfully.
IMPORTANT: Always
use low-torque settings;
NEVER over-tighten.
NOT E : AD J U S T I N G T H E
T E N S I O N O F T H E
R LOTO O C K C L A M P S S O
THAT THE SP EA KE R FRAM E IS F LAT WILL HE LP E NSU RE THAT THE
GR ILL E CONTACTS THE WAL L ALL THE WAY AROU ND THE SP EAKER
FOR A P ROP ER F IT.
6. The new micro-trim grille is held in place by several small,
powerful magnets on the speaker frame. Place the grille
against the speaker and the magnets will hold it firmly in
place. When properly installed, the grille trim should make
contact with the wall all the way around the speaker.
Painting the Grilles
Please refer to the accompanying
Painting Instructions
sheet for
painting instructions.
Speaker Adjustments
Pivoting Tweeter
All Visual Performance Series in-wall speakers have a pivoting
tweeter that allows you to direct sound towards or away from the
listening area, depending on how the speakers are being used:
• If you’re using the speakers in stereo or as the front left/center/
right speakers in a home theater, pivot the tweeter directly
towards the listening area. This will help the sound from the
speakers blend into a solid soundstage even if the speakers are
widely separated.
• If you’re using the speakers as surround channel speakers in a
home theater, you can create a more diffuse, spacious
surround effect by pivoting the tweeter towards a wall or
window, away from the listeners.
To pivot the tweeter, apply
light pressure to the plastic
ring around the outside edge
of the tweeter dome, as
shown in
Figure 9
. Take care
not to touch or apply
pressure to the tweeter dome
itself.
FIGURE 9: PIVOTING THE WEETERT
Roto-Lock
Screws
FIGURE 8: TIGHTENING THE
R -L SOTO OCK CREWS

Termékspecifikációk

Márka: Sonance
Kategória: hangszóró
Modell: Visual Performance VP69

Szüksége van segítségre?

Ha segítségre van szüksége Sonance Visual Performance VP69, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók hangszóró Sonance

Sonance

Sonance Mariner MX52 Útmutató

2 Január 2025
Sonance

Sonance Visual Performance VP65 SST Útmutató

16 Október 2024
Sonance

Sonance Landscape LS6T SAT Útmutató

7 Október 2024
Sonance

Sonance Visual Performance VP87 Útmutató

6 Október 2024
Sonance

Sonance Mariner MX66 Útmutató

11 Szeptember 2024
Sonance

Sonance MAG06V3 Útmutató

2 Szeptember 2024
Sonance

Sonance Visual Performance Útmutató

31 Augusztus 2024
Sonance

Sonance Garden SGS Subwoofer Útmutató

11 Augusztus 2024
Sonance

Sonance Visual Performance VP61 Útmutató

8 Augusztus 2024
Sonance

Sonance IS4 Útmutató

7 Augusztus 2024

Útmutatók hangszóró

Legújabb útmutatók hangszóró

Lenco

Lenco PA-101 Útmutató

5 Január 2025
Majority

Majority D100 Útmutató

5 Január 2025
Audibax

Audibax Roma 120 Go Útmutató

5 Január 2025
Audibax

Audibax Detroit 200 Go BT Útmutató

5 Január 2025
Audibax

Audibax Detroit 1000 DSP Útmutató

5 Január 2025
Audibax

Audibax Denver 10 Útmutató

5 Január 2025
Audibax

Audibax GA04 Útmutató

5 Január 2025
Audibax

Audibax Oasis 6T Útmutató

5 Január 2025
Audibax

Audibax Seattle 500 Útmutató

5 Január 2025
Audibax

Audibax Delta 32 BT Útmutató

5 Január 2025