Használati útmutató Smart-AVI SM-EDPN-2S

Smart-AVI kapcsoló SM-EDPN-2S

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Smart-AVI SM-EDPN-2S (4 oldal) a kapcsoló kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/4
SM-EDPN KVM
with Barco Monitor mdcc-6530
USER MANUAL
Designed and Manufactured in the USA
1-800-284-2131
www.smartavi.com
SM-EDPN-2S 2-Port Single-Head DP KVM Switch with Aux Emulation
SM-EDPN-2D 2-Port Dual-Head DP KVM Switch with Aux Emulation
SM-EDPN-2Q 2-Port Quad-Head DP KVM Switch with Aux Emulation
SM-EDPN-4S 4-Port Single-Head DP KVM Switch with Aux Emulation
SM-EDPN-4D 4-Port Dual-Head DP KVM Switch with Aux Emulation
SM-EDPN-4Q 4-Port Quad-Head DP KVM Switch with Aux Emulation
SM-EDPN-8S 8-Port Single-Head DP KVM Switch with Aux Emulation
2/4/8-Port DP KVM Switch with Audio and USB 2.0 Support 2
Installation
BARCO MONITOR KVM SETUP:
1. Start by connecting your DP input cables from your various devices ONLY to the ports labeled A on
the unit. Then connect the DP output cable from the Barco monitor. This DP cable needs to be from
port marked DP output 1 on the monitor. You should have up to 4 inputs cables coming from various
devices and 1 output cable going to the Barco monitor plugged into the unit at this point.
Note: You must use the cable coming from DP output 1 on the Barco monitor for this process to work. If
you are unsure about which port that is, consult the manual for your respective Barco monitor.
1
2 3 4 5 6 7
8
NUMBER DESCRIPTION
1 Kensington security slot
2 Service port (for Barco service purposes only)
3 DisplayPort IN2
4 DisplayPort OUT (covered with a plastic cap by default, remove the cap to use this connector)
5 DisplayPort IN1
6 USB-A 2.0 downstream connectors (2x)
7 USB-B 2.0 upstream connector
8 100-240 VAC mains power input and power switch
2. Make sure your Barco monitor has the correct settings for each video input by using the monitor’s
on-screen display menu. The settings you are looking for in the monitor’s OSD is called EDID timings
and the correct settings are the following: Resolution should be , Refresh Rate should be , 3MP+ High
and Color Depth should be .8 bit
DisplayPort IN1
2/4/8-Port DP KVM Switch with Audio and USB 2.0 Support 3
Installation (continued)
6. Power on the unit. After a few moments, you should now have video on both halves of the Barco
screen. Verify the output video is correct using the same process from step 3. Then enter in the
following sequence on the keyboard: Ctrl + Ctrl + L + 2 + Enter.
7. You can now nish connecting the rest of the cables you have such as other USB cables or audio
cables.
Note: These steps lock the monitor info into the KVM. It will improve performance but if you connect
any other monitor, especially with the strange resolution we’re locking it at, you won’t see video. If you
ever need to use different monitors, be sure to factory reset the KVM with Ctrl + Ctrl + f + enter.
Note: The unit used in the example images is a 4-port quad-head unit, but the instructions are still
applicable to other units such as a 2-port dual-head unit.
3. Power on the unit. After a few moments, you should now see video on one half* of the Barco monitor.
Connect a keyboard and mouse to the K/M slots on the unit. Connect the USB cable (USB male-A
to USB male-B) to the port marked USB for IN 1 on the unit and to a USB port on the device. Check
the video settings to make sure you have the correct resolution, refresh rate, color, and EDID. The
correct settings should be: , , and color. The device’s EDID, device name e.g. 1536x2048 50Hz 8 Bit
MDCC-4430, should also be shown.
* The video should show up on the left side of the monitor. If the video shows up on the right Note:
you’re on DisplayPort IN2. If the video shows up in the center the monitor is set to one source,
change the setting in the monitor to 2 sources.
4. Once you have veried that the resolution is correct, enter the following sequence on the keyboard
to lock the monitor EDID: Ctrl + Ctrl + L + 1 + Enter. This will save the monitors information to the
unit.
5. Power off the unit. Then connect the rest of the inputs to the ports labeled B on the unit. Now swap
the output cable that was previously connected to output labeled A on the unit to the output labeled
B. Then connect the output cable coming from the Barco monitor port labeled DP output 2 to the
output labeled A on the unit.
DisplayPort IN2
DisplayPort IN1

Termékspecifikációk

Márka: Smart-AVI
Kategória: kapcsoló
Modell: SM-EDPN-2S

Szüksége van segítségre?

Ha segítségre van szüksége Smart-AVI SM-EDPN-2S, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók kapcsoló Smart-AVI

Útmutatók kapcsoló

Legújabb útmutatók kapcsoló