Használati útmutató Sjoef Classic BIS20M1

Sjoef kerékpár Classic BIS20M1

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Sjoef Classic BIS20M1 (14 oldal) a kerékpár kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/14
1
Instrucons Manual
keep this manual
Handbuch
Bewahren Sie dieses Handbuch
Handleiding
Bewaar deze handleiding
S J O E F
Amsterdam
Made in China
in China hergestellt
Gemaakt in China
Bisshops BV
Herengracht 338
1016 CG Amsterdam
The Netherlands
2
EN - Manual
This manual provides instrucons for assembling and maintaining your new SJOEF
bicycle. Before assembling the bicycle, it is important to follow these steps.
Remove the bicycle from the packaging and place all the parts together. Be
careful not to leave any parts inside the packaging.
Check that all parts are present
Assembly is intended for adults only
Tip: Are you having trouble with the assembly? Then please contact our customer
service.
The bicycles are manufactured to comply with European standards EN ISO-
8098:2014 or EN ISO-4210:2014. Please note: the manufacturer is not responsi-
ble for improper use or incorrect assembly of the bicycle.
Assembly
The bicycle can be assembled in a few simple steps. It is important to follow the
order of the instrucons in order to make the assembly as easy as possible.
Installaon of the saddle
1. Insert the saddle pillar into the seatpost.
2. Adjust the saddle to the correct height. Observe the safety mark on the
saddle pillar, which should disappear into the frame. The saddle is at the right
height when your toes touch the ground while standing sll. If possible, the
saddle should be adjusted so that the enre foot is on the ground.
3. Is the saddle at the right height? Lock the saddle by ghtening the saddle
bolt.
Installing the handlebar and stem (if required)
1. Insert the stem (including handbrake lever and bell if present) into the frame.
2. Observe the safety marking on the stem, it should disappear into the frame.
3. Posion the handlebar at the desired height and check whether it is perpen-
dicular to the front wheel.
4. Tighten the handlebar clamp and/or bolt.
Installing the pedals
PLEASE NOTE: there is an (L) on the le and an (R) on the right side of the pedal.
Incorrectly ghtening the pedal will render the bike unusable and will void the
warranty.
3
1. It is advisable to grease the ends of the pedals so that they can be replaced
easily in the future.
2. An L or R can be read o from the axle of the pedal. Use this to check which
pedal should be ed on the le and which on the right. Are there no L or R
on the pedals? Then the le pedal contains a marking in the form of a line.
3. Insert the right pedal into the crank and turn the pedal clockwise by hand
towards the front wheel. It should be easy to turn the pedal; if it is s, the
thread may be damaged.
4. Then turn the le pedal by hand counter-clockwise into the crank, also in the
direcon of the front wheel.
5. Finally, ghten the pedals even further using an open-end spanner.
Checking the cranksha nut
There are a number of bicycles in which the le-hand crank is secured with a
crank nut. Before using the bike, check that this nut is properly ghtened:
1. First ghten the nut with the 6 sides (clockwise).
2. Then ghten the lock nut (3 notches).
Fing the side wheels (if available)
1. Fit the support wheel arm on the rear axle against the locking plate which is
already ed on the rear axle). Alternavely, if present, secure the addional
plate on the rear frame with 2 screws.
2. Make sure that everything is rmly aached to the rear axle.
3. The quick release and protecon plate (if applicable) should only be slid onto
the rear wheel axle.
4. Screw the outer axle nut ght when the desired height of the side wheels has
been found. The side wheels should stay about 6 mm above the ground on
both sides.
Fing the front wheel (if necessary)
1. Posion the front wheel in the middle of the front fork.
2. Subsequently, ghten the nuts alternately while keeping the front wheel
straight in the middle of the front fork.
Installing the front mudguard (if required)
1. Unscrew the nuts with washers from the screw bolt.
2. Insert the screw bolt through the hole in the front frame/fork (make sure that
one ring remains at the front).
3. Fit the front reector or headlight (if any) between the ring and the front
end of the bolt. Ensure that the front reector (or front light) remains in the
correct posion by holding it with one hand.
4. If not already in place, push the hook hanging from the mudguard upwards.
Place the hook at the back of the hole in the frame/fork on the bolt.
5. Next, place the washer and nally ghten the nut.
6. Check whether the front reector (or lighng) is upright. You can then ghten
the nut rmly.

Termékspecifikációk

Márka: Sjoef
Kategória: kerékpár
Modell: Classic BIS20M1

Szüksége van segítségre?

Ha segítségre van szüksége Sjoef Classic BIS20M1, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók kerékpár Sjoef

Útmutatók kerékpár

Legújabb útmutatók kerékpár