Használati útmutató Samsung SKK-8K

Samsung Szárítógép SKK-8K

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Samsung SKK-8K (3 oldal) a Szárítógép kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/3
CAUTION : Two people are required to lift the dryer on to
the washer.
WARNING : These washer and dryer are not suitable for
mobile home or RV installation.
Dryer
STEP 1 Have two persons place the dryer on a non-slippery
floor. Then, have one person tilt the dryer to the side.
Do not lay the dryer down. The dryer may be scratched.
STEP 2-1 SKK-7*, SKK-8*: Check if the legs are tightened up,
and then insert the stacking support guides in the
rectangular holes of the dryer’s base until you hear a
clicking sound. You don’t need to remove the legs.
STEP 2-2 SKK-BB: Disassemble legs, and Snap the stacking
support guides into the rectangular holes in the dryer
base and secure each with two(2) screws Phillips-pan
head (6006-001174)
STEP 3 Repeat the same step above on the other side.
STEP 4 Bottom view of the dryer after assembling the Stacking
Support Guides to the dryer base.
* Use a stacking-kit compatible with the purchased model.
Washer (Stacking kit: SKK-7*, SKK-8*, for 27” models)
CAUTION : You need to use the proper rear bracket
depending on your washer model. (There are 2 different
rear brackets : DC61-04160A, DC61-04955A)
5-1) DC61-04160A :
WF5*K**, WF4*H**, WF4*K**, WF4*M**, WF4*N**,
WF18H**, WF20H**, WF20M**, WF22H**, WF22K**,
WF15K**, WF16J65**
Left Right
DO NOT TIGHTEN SCREWS COMPLETELY
STEP 5-1 LOOSELY assemble the Rear Brackets
(DC61-04160A) to the washer as shown below. Use
two (2) Screws-Hex Head (6002-001431) with washers
(DC60-00044A) in each washing machine Top Cover tail,
per bracket.
* Before installing the rear bracket, loosen two screws
(Screw-Hex) on the Cover Top that is secured to the frame.
5-2) DC61-04955A :
WF5*R**, WF4*R**
Left Right
DO NOT TIGHTEN SCREWS COMPLETELY
STEP 5-2 LOOSELY assemble the Rear Brackets (DC61-04955A)
to the washer as shown below. Use two (2) Screws-Hex
Head (6002-001431) with washers (DC60-00044A) in
each washing machine Top Cover tail, per bracket.
* Before installing the rear bracket, loosen two screws
(Screw-Hex) on the Cover Top that is secured to the frame.
Washer (Stacking kit: SKK-BB, for 30” models)
WF56H**
STEP 5-3
Loosely assemble the Rear Bracket (DC61-03846A) to
the washer as shown above in either case A or Case B,
Use (2) Screws-Hex Head (6009-001476) with washers
(DC60-00044A) to the each hole of Cover Top and Frame.
* Case A only : Before installing the rear bracket, loosen two screws
(Screw-Hex) on the Cover Top that is secured to the frame.
Case A Case B
Small Cap Big Cap
STACKING KIT INSTALLATION INSTRUCTIONS (WASHER & DRYER ONLY)
DC68-01052R-09
STACKING KIT INSTALLATION INSTRUCTIONS (WASHER & DRYER ONLY)
STEP 6 Lift and position dryer
into the position on the
washer shown above, slide
dryer backwards to make
contact with rear brackets.
STOP
HERE
CAUTION : To prevent noise, check the followings.
• Make sure the washer is level.
• Make sure the dryer’s leveling legs are tightened up.
(Stacking kit: SKK-7*, SKK-8*, for 27” models)
STEP 7 Align rear brackets with
mounting holes on the
rear of dryer as shown
above.
STEP 8 LOOSELY assemble rear
brackets to the back of
the dryer using two (2)
Screws- Phillips Pan Head
(6006-001174) for each
rear bracket as shown
above.
Extra screws may be
included with this kit.
STEP 9 Tighten screws on the
dryer side of the rear
bracket.
WARNING : Additional gas hook-up components are
required for gas dryer.
STEP 10 Tighten screws on the
washer side of the rear
bracket.
* DO NOT REVERSE THE ORDER OF
STEPS 9 & 10.
STEP 11 Stacked Unit is now ready
to be installed. Refer
to detailed installation
instructions packed with
products.
Stacking kit components
Stacking Support Guides (2)
SKK-7*, SKK-8*
- DC61-04159A
Rear Bracket (2) (WF5*K**, WF4*H**,
WF4*K**, WF4*M**, WF4*N**, WF18H**,
WF20H**, WF20M**, WF22H**,
WF22K**, WF15K**, WF16J65**)
SKK-7*, SKK-8*
- DC61-04160A
Rear Bracket (2) (WF5*R**, WF4*R**)
SKK-7*, SKK-8*
- DC61-04955A
Stacking Support Guides (2)
SKK-BB
- DC61-01480B
Rear Bracket (2) (WF56H**)
SKK-BB
- DC61-03846A
Screws-Hex Head (4)
SKK-BB
- 6009-001476
SKK-7*, SKK-8*
- 6002-001431
Screws Phillips-Pan Head (8) - 6006-001174
Washer (4) - DC60-00044A
Rear Bracket
(WF5*K**, WF4*H**,
WF4*K**, WF4*M**,
WF4*N**, WF18H**,
WF20H**, WF20M**,
WF22H**, WF22K**,
WF15K**, WF16J65**)
Rear Bracket
(WF56H**)
Rear Bracket
(WF5*R**, WF4*R**)
Screw-Hex Head
SKK-BB (M5, L10)
SKK-7*, SKK-8* (M5, L16)
Screw Phillips-Pan
Head
(M4, L12)
Washer (ID5, OD10)
Stacking Support Guide

Termékspecifikációk

Márka: Samsung
Kategória: Szárítógép
Modell: SKK-8K

Szüksége van segítségre?

Ha segítségre van szüksége Samsung SKK-8K, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Szárítógép Samsung

Samsung

Samsung DVE54CG7150W Útmutató

14 Január 2025
Samsung

Samsung DVE55CG7100V Útmutató

3 Január 2025
Samsung

Samsung DVG55CG7100V Útmutató

3 Január 2025
Samsung

Samsung DVE52A5500W Útmutató

14 Szeptember 2024
Samsung

Samsung DV70M5200KW Útmutató

3 Szeptember 2024
Samsung

Samsung SDC3C803 Útmutató

3 Szeptember 2024
Samsung

Samsung DV90CGC0A0TH Útmutató

31 Augusztus 2024
Samsung

Samsung DV91CGC2A0AH Útmutató

29 Augusztus 2024
Samsung

Samsung DV11H4100CW Útmutató

29 Augusztus 2024
Samsung

Samsung DVE51CG8005V Útmutató

29 Augusztus 2024

Útmutatók Szárítógép

Legújabb útmutatók Szárítógép

Bauknecht

Bauknecht traa prestige Útmutató

10 Április 2025
Bauknecht

Bauknecht TRK 9876 Útmutató

10 Április 2025
Asko

Asko TH208HW Útmutató

10 Április 2025
Zanussi

Zanussi ZTA 245 Útmutató

9 Április 2025
Bauknecht

Bauknecht TKL M11 72 Útmutató

9 Április 2025
Amana

Amana NGD4600YQ Útmutató

9 Április 2025
Whirlpool

Whirlpool awz 9479 Útmutató

9 Április 2025
AEG

AEG 65770IH3 Útmutató

7 Április 2025
Arçelik

Arçelik 901 KMP IG Útmutató

7 Április 2025
Arçelik

Arçelik 901 KMP I Útmutató

7 Április 2025