Használati útmutató Salus KL04RF

Salus okos otthon KL04RF

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Salus KL04RF (2 oldal) a okos otthon kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

KL04RF

Installation and Wiring Guide

www salus-controls com Technical Helpline +44 (0) 1226 323 961

These instructions apply to the SALUS model stated above.

Warning

This product must be fitted by a competent person, and

installation must comply with the guidance, standards and

regulations applicable to the country or state where the

product is installed. Failure to comply with the requirements of

the relevant guidance, standards and regulations could lead to

injury, death or prosecution.

Warning

Always isolate the AC mains supply before installing or working

on any components that require 230 VAC 50Hz supply.

For PDF Installation guide go to www.salus-controls.com

Warning

The earth terminals on the KL04RF are for earth parking only.

These terminals provide no earth protection.

Meets the following EC Directives

• Electro-Magntic Compatibility directive 2004 / 108 / EC

• Low-voltage Directive 2006/95/EC

Maintaining a policy of continued product development SALUS Controls plc reserves the right to change

specication, design and materials of products listed on this installation guide without prior notice.

Issue Date: November 2014 Document Number 00106

GROUP 2

THERMOSTAT

HTRS-RF(30)

GROUP 2

THERMOSTAT

HTRS-RF(30)

GROUP 2

THERMOSTAT

HTRS-RF(30)

GROUP 2

THERMOSTAT

HTRP-RF (50)

SUPPLIED CABLES

UNDERF OR HEATING MANIFOLDLO

HTRS-RF

(

)

TRS-RF

(

)

HTRS-RF

(

)

HTRP-RF

(

KL04RF

Installation and Wiring Guide

Installing and Connecting the KL04RF

7Attach the white strain-relief

using the two screws to

secure the power wires.

10 Attach the short ribbon cable

between the KL08RF and KL04RF

for side installation otherwise

use the long ribbon cable.

The following shows the side

installation:

2Remove the white terminal

connection board.

9Remove the plastic cover on the

KL08RF.

Attach the back of the KL04RF

to the DIN rail or wall. If you are

tting the KL04RF to the side of

the KL08RF, use the short ribbon cable

otherwise use the long ribbon cable

(see step 10). The following shows the

side-mounted, wall installation:

8Push the actuator wires into

the holes at the bottom of the

KL04NSB. You can connect up to

four actuators in each zone.

11 Push out the cutout on the

bottom of the cover of the

KL04RF.

4Cut the power and device cables

to length.

5Replace the white

connection board.

13 Switch on mains power

supply to the unit. The red

LED comes on.

www salus-controls com Technical Helpline +44 (0) 1226 323 961

Use the KL04RF wireless wiring centre extension to simply and safely connect an additional four thermostats and actuators. Use the KL04RF only together with the KL08RF wireless

wiring centre. Install the KL04RF only in dry and closed interior rooms. Relative air humidity in the room may not exceed 95%. Clean the KL04RF only with a dry and soft cloth.

Do not use solvents or aggressive cleaning agents.

LED indications

Name Colour Meaning

Connection

•

KL04RF is connected to the KL08RF

Power

•

KL04RF is supplied with 230V power

Zone 9 actuators

•

Demand from zone 9 thermostat, actuator open