Használati útmutató Roland KD-A22

Roland nincs kategorizálva KD-A22

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Roland KD-A22 (6 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 10 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/6
Owner’s Manual
Watch the Quick Start Video
“Installing the KD-A22”
http://roland.cm/kd-a22
Introduction
The KD-A22 can be installed on a 22-inch acoustic bass drum.
Fully assembled view
* A 22-inch acoustic bass drum is not included with this product.
When using a drum stand (MDS-50K/MDS-50KV)
For the MDS-50K/MDS-50KV, the spacing of the bass drum installation area
is as follows.
Vertical: 590 mm (23-1/4”)
Horizontal: 620 mm (24-7/16”)
620 mm
(24-7/16”)
590 mm
(23-1/4”)
Check the Included Items
After opening the package, check that all of the included items are
present. If anything is missing, contact your dealer.
Front head
Batter head
NOTE
Do not pull the cable that is attached to the batter head.
Batter board
NOTE
A circuit board is attached to the batter board. To prevent injury,
damage, or accident, observe the following points.
5
Do not touch the circuit board with your ngers.
5
Do not lay down the batter board with the circuit board facing
downward.
5
Do not apply excessive force to the circuit board.
Batter hoop
* Batter board spacers (6 pcs.) are
already attached
Batter board stopper x 4
Connection cable
Drum key
Before using this unit, carefully read “USING THE UNIT SAFELY” and
“IMPORTANT NOTES” (p. 6). After reading, keep the document(s) where it will
be available for immediate reference.
Copyright © 2016 ROLAND CORPORATION
2
Installing the KD-A22
Caution during installation
5
Before you begin the installation procedure, lay down a mat to
protect the oor or the drum from scratches.
5
When turning the bass drum upside down, take care not to drop
it or let it overturn.
5
Muting (such as using weights or a blanket) is not necessary.
Remove such materials from the bass drum. Also, do not install
muting after installing the KD-A22.
1. Attaching the Batter Head
1. Place the bass drum so that the striking surface head is
upward.
2. Loosen the lugs, and remove the hoop and head.
3. Place the batter head on the shell so that the hole in the
batter head is positioned as shown in the illustration.
NOTE
This placement of the batter head assumes that you are using
a single pedal. If you are using a twin pedal, you might need
to adjust the batter head hole position depending on the kick
pedal that you are using. For details, refer to “Using double kick
pedals” (p. 5).
Adjust the position of the batter
head so that the pin is aligned with
the center of the shell as shown in
the illustration.
Hole Pin
Top
Pin
4. Place the batter hoop on the batter head, and adjust the
position of the batter hoop so that the centers of the
batter hoop and batter head are aligned.
Place the batter hoop on the
batter head so that the pedal
attachment hardware is at this
location.
5. Move the batter board spacers attached to the batter
hoop to the positions shown in the illustration.
For a bass drum with eight lugsFor a bass drum with ten lugs
6. Working alternately across opposite sides of the drum,
lightly tighten each lug until the lugs do not wobble.
1
3
4
6
2
8
9
10
57
7. Then tighten each lug another 3/4 of a turn to secure the
batter head.
NOTE
If the batter head is not secured suciently, the sensor might
malfunction, or the sound of the strike might be too loud.
8. Move the batter board spacers attached to the batter
hoop in the directions shown by the arrows, so that they
rmly contact the lugs.
For a bass drum with eight lugsFor a bass drum with ten lugs
3
2. Attaching the Batter Board
1. Align the batter board’s circuit board cover with the hole
in the batter head, and place the batter board.
Hole
Circuit board cover
NOTE
Take care that the batter board’s circuit board cover does not
rest on the batter head or catch on the hole. Forcing it could
damage the circuit board/circuit board cover or the battery
head.
2. As shown in the illustration, align the center of batter
head’s strike surface and center of the batter board hole.
Align the center
Batter board
Striking surface of
the batter head
3. Lightly press down the batter board so that it rmly
contacts the batter head.
Batter board
Batter head
Batter board spacer
Batter hoop
Batter board spacer
3. Attaching the Batter Board Stoppers
Attach the included batter board stopper (4 pcs.) to the batter
hoop.
NOTE
When attaching the stoppers, take care not to hurt your hand
on the lugs.
1. Push down on the batter board stoppers in a location
where your hand will not strike the lug.
Batter board stopper
* It is easier to attach the
stoppers if you spread
them open as shown in the
illustration while pushing
them onto the batter hoop.
Press with the palm of your hand
Grasp this part
with your ngers
2. Position the batter board stoppers as shown in the
illustration.
For a bass drum with eight lugsFor a bass drum with ten lugs

Termékspecifikációk

Márka: Roland
Kategória: nincs kategorizálva
Modell: KD-A22

Szüksége van segítségre?

Ha segítségre van szüksége Roland KD-A22, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók nincs kategorizálva Roland

Roland

Roland MDS-50K Útmutató

3 Április 2025
Roland

Roland CB-76RL Útmutató

3 Április 2025
Roland

Roland OP-RMP12 Útmutató

3 Április 2025
Roland

Roland RH-L20 Útmutató

3 Április 2025
Roland

Roland M-UF1G Útmutató

3 Április 2025
Roland

Roland CB-88RL Útmutató

3 Április 2025
Roland

Roland 7X7-TR8 Útmutató

3 Április 2025
Roland

Roland CB-CS1 Útmutató

2 Április 2025
Roland

Roland CB-MCC1 Útmutató

2 Április 2025
Roland

Roland CB-HPD Útmutató

2 Április 2025

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

Planet

Planet PWR-240-48 Útmutató

9 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
Alpine

Alpine DP2-40C-BC Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025
IFM

IFM PG1704 Útmutató

9 Április 2025
Daikin

Daikin EKWCTRDI1V3 Útmutató

9 Április 2025
Simplified MFG

Simplified MFG SP18CAT120 Útmutató

9 Április 2025