Használati útmutató Rega RB880

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Rega RB880 (4 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/4
USER MANUAL
Introduction
Designed using the latest 3D CAD & CAM technology,
the new RB880 is the culmination of almost 40
years of tonearm design experience. This tonearm
features a new aluminium vertical bearing housing,
a redesigned sleeve and vertical bearing shaft
(both manufactured from stainless steel) to
improve mounting stability and overall rigidity. The
advanced tonearm tube is designed using intelligent
redistribution of mass, ensuring this arm will exhibit
fewer points of possible resonance. The extreme
levels of stability achieved, coupled with almost
friction free movement from the high precision hand
matched bearing assemblies, guarantee to gather
more information from your vinyl than ever before.
You will also nd Rega made new low capacitance
phono cables terminated with high specication
phono plugs.
Arm balancing and setup
With the cartridge correctly mounted and with the
stylus guard removed, ensure that the tracking force
dial and bias adjustment are set to zero. Adjust the
balance weight until the arm is “oating”, with the
stylus approximately 1mm clear of the record.
Note: It is normal for the arm to swing back towards
the arm clip position even with the bias set at zero.
Therefore, it is advisable to gently hold the arm
bearing carrier (just below the tracking dial) thus
preventing horizontal movement during the balancing
procedure.
Applying tracking pressure
Once the arm is balanced, rotate the tracking force
adjustment dial to the required tracking force.
Numbers ‘0’ to ‘3’ are marked on the dial. If in doubt,
it is usually advisable to use a tracking force that
corresponds with the upper limits of the cartridge
manufacturers range.
Applying Anti - Skating (bias) adjustment
Set the bias adjustment slider located to the same
gure as the cartridge tracking force pressure quoted
by your cartridge manufacturer. This is not Note:
critical and a gure between 1.5 & 2.0 will normally be
suitable for most moving magnet cartridges.
Your arm is now balanced, setup and ready to use. If
you have any doubts regarding installation or setup,
please contact your ofcial Rega dealer who will be
able to carry out the work for you. Thank you for
purchasing this Rega product and we wish you many
hours of musical enjoyment.
Bias adjustment
Balance weight
Tracking dial
Cueing device
li/lower handle
Arm clip
Finger li
(1:4 scale)
Headshell
Protractor and
arm mounting
data included.
Cueing
platform

Termékspecifikációk

Márka: Rega
Kategória: nincs kategorizálva
Modell: RB880

Szüksége van segítségre?

Ha segítségre van szüksége Rega RB880, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva Rega

Rega

Rega ND5 Útmutató

26 Szeptember 2024
Rega

Rega Atlas MK2 Útmutató

12 Szeptember 2024
Rega

Rega Nd3 Útmutató

1 Szeptember 2024
Rega

Rega Fono MM MK5 Útmutató

30 Augusztus 2024
Rega

Rega Fono MC MK4 Útmutató

30 Augusztus 2024
Rega

Rega Aura MC Útmutató

30 Augusztus 2024
Rega

Rega Aria MK3 Útmutató

30 Augusztus 2024
Rega

Rega RB78 Útmutató

29 Augusztus 2024
Rega

Rega RB220 Útmutató

29 Augusztus 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva