Használati útmutató RDL FP-TPX3A

RDL Kézi turmixgép FP-TPX3A

Olvassa el alább 📖 a magyar nyelvű használati útmutatót RDL FP-TPX3A (2 oldal) a Kézi turmixgép kategóriában. Ezt az útmutatót 10 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
FLAT-PAK™ SERIES
Model FP-TPX3A
Format-A Twisted Pair
Remote Controlled Mixer
3-Channel Remote-Controlled Audio Mixer
VCA Level Control for Each Input Pair
Format-A Twisted Pair Inputs
Balanced and Unbalanced Outputs
Two Mono Unbalanced Outputs to Feed Stereo Amplifier
Inputs and Outputs on Detachable Connectors
Twisted Pair Interconnection to Remote Control
Directly Controlled by RDL Remote Controls
Two and Three Channel Remote Controls Available
Local Input Available if Only Two Twisted Pair Inputs Used
Paging Source May Connect to Local Input
Front-Panel Gain Trim Matches Active or Passive Format-A Senders
Dual-LED VU Meter Displays Mixer Output Level
Audio Presence Detector Controls Open-Collector Outputs
Detector Outputs Intended to Enable Power Amplifiers or System Power
Energy Savings Possible Using Detector Outputs
Selectable 10 or 20 Minute Detector Release Delay
The FP-TPX3A is a mono audio mixer in the convenient line of FLAT-PAK products, featuring the superior engineering and components common
to RDL products. The FP-TPX3A may be rack or surface mounted with optional FLAT-PAK series accessories. The FP-TPX3A gives you the
advantages of a quality audio mixer with the added convenience of remote control!
The FP-TPX3A is the ideal choice where a user-accessible mixer must control the volume of multiple sources in a zone. RDL Format-A
twisted pair audio senders connect directly to the mixer, allowing each user input to be balanced or unbalanced, mic or line level.
FP-TPX3A outputs are provided in balanced and unbalanced formats. Two unbalanced outputs are available to feed the mono mixer
output to a stereo amplifier input. Remote control of the mixer allows audio signals to be kept at a single equipment location. Audio is
mixed by VCA circuits that are adjusted by control signals from the remote control.
Two Format-A jacks are provided for signal inputs. If the Format-A senders are daisy-chained, only one of the input jacks is used. The
other input jack may be used to receive another Format-A sender, or may be used to loop the received Format-A signals out to additional
Format-A mixers or receivers. The FP-TPX3A provides power to all connected active senders. The FP-TPX3A is designed to mix the
three Format-A audio signals from pairs A, B and C. A front-panel switch allows the PAIR C mixer input to be fed either from the twisted
pair C input signal or from a local input. A detachable terminal block is provided to connect a local paging or music source to the
LOCAL INPUT. Note: Pair C signals are passed through both Format-A input jacks even if the mixer is set to use a local source instead of
the PAIR C twisted pair source.
Format-A senders are available in active and passive models. Passive Format-A models with unbalanced input jacks send a lower signal
level to the mixer than is sent by active senders or by passive senders with balanced inputs. Each INPUT GAIN control is calibrated to be
adjusted clockwise for an unbalanced passive sender; counter-clockwise for an active sender or passive sender with a balanced input.
A standard RDL dual-LED VU meter provides visual indication of the output level from the mixer. Each input channel operates at unity gain
when the corresponding remote control is adjusted to maximum. This assures ample headroom at all normal operating levels. The mixer
output is mono. The output is available on a single balanced detachable terminal block or on two unbalanced RCA jacks intended to
connect directly to the stereo input of a power amplifier.
The AUDIO LED illuminates whenever audio is present at the output of the mixer, defined as greater than 35 dB below +4 dBu. This
threshold triggers the AUDIO DETECT OUTPUTS. Two open collectors are provided on a detachable terminal block. One of these
terminals switches low when audio is present, and may be used to switch amplifiers or other system components on. The other terminal is
pulled low when audio is not present. It is intended for muting the digital carrier of power amplifiers equipped for remote muting. Either of
these terminals may be used to trigger a vari The use of these terminals to shut downety of other RDL modules or OEM equipment.
unused equipment can produce effective system energy and cost savings. These control terminals normally remain triggered for 10
minutes after audio is absent. The delay can be increased to 20 minutes using a ground jumper on the terminal block.
The mixer levels are set by RDL remote controls that connect directly to the FP-TPX3 through an RJ45 jack using standard twisted pair
cable. The control ports on the mixer and remote controls are color-coded light blue to distinguish them from standard Format-A jacks. The
mixer provides power to the remote control. Either a two or three channel remote control may be used. If remote mixing of only two
channels is needed, a two channel remote may be used. Pair C becomes the i motely controlled. The nput channel that is not re
PAIR C/LOCAL INPUT can be left active at unity gain, typically for a paging source, or may be disabled by a switch set during installation.
If the cable connected to the remote control he mixer output mutes. becomes disconnected, t
RDL
659 6th St.
Prescott, AZ., USA 86301
(928) 443-9391 FAX (928) 443-9392 www.rdlnet.com
TYPICAL APPLICATIONS:
► Meeting Rooms
► Boardrooms
► Classrooms
► Restaurant or Residential Patios
► Retail Stores
ASSOCIATED REMOTE CONTROL EXAMPLES:
► D-RC2 and DS-RC2 Two-channel remote controls
► D-RC2M and DS-RC2M Two-channel remote controls with muting
► D-RC3 and DS-RC3 Three-channel remote controls
► D-RC3M and DS-RC3M Three-channel remote controls with muting
FLAT-PAK™
SERIES
Model FP-TPX3A
Format-A Twisted Pair
Remote Controlled Mixer
TYPICAL PERFORMANCE
Inputs (3): RDL FORMAT-A; Balanced line level
Input Connections: RJ45 (FORMAT-A); Detachable Terminal Block (Pair C)
Outputs (3): 150 Ω balanced; 1 kΩ unbalanced (2)
Output Connections: Detachable Terminal Block (balanced); RCA Phono Jacks (unbalanced)
Output Level: +4 dBu balanced, -10 dBV unbalanced
Frequency Response: 20 Hz to 20 kHz (+/- 0.25 dB)
THD+N: < 0.05% (20 Hz to 20 kHz); <0.02% (1 kHz)
Noise below +4 dBu: < -100 dB (all channels off); <-75 dB (any channel on); <-70 dB (all channels on)
Headroom above +4 dBu: > 18 dB
CMRR: > 80 dB (50 Hz to 150 Hz)
VCA attenuation: >90 dB (each input, remote control volume off)
Indicators (3): Dual-LED VU meter (2); Audio present (threshold = 35 dB below +4 dBu output)
Power Connections (3): Terminal block; dc power jack (2)
Power Requirement: 24 Vdc @ 120 mA plus connected FORMAT-A sender currents
Overall Dimensions: Height: 1.42 in.3.61 cm
Width: 3.25 in. 8.26 cm
Length: 8.14 in. 20.68 cm
Installation/Operation
Declaration of Conformity available from rdlnet.com.
Sole EMC specifications provided on product package.
Specifications are subject to change without notice.
Radio Design Labs Technical Support Centers
U.S.A. (800) 933-1780, (928) 778-3554; Fax: (928) 778-3506
Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287
891-2145E
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rule. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. The equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off an
on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment
and receiver
Connect the equipment into an outlet on a circuit
different from that which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.

Termékspecifikációk

Márka: RDL
Kategória: Kézi turmixgép
Modell: FP-TPX3A

Szüksége van segítségre?

Ha segítségre van szüksége RDL FP-TPX3A, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Kézi turmixgép RDL

RDL

RDL RU-MX5ML Útmutató

19 Augusztus 2024
RDL

RDL ST-MX2 Útmutató

18 Augusztus 2024
RDL

RDL ST-UMX3 Útmutató

18 Augusztus 2024
RDL

RDL ST-MX3 Útmutató

18 Augusztus 2024
RDL

RDL HD-RA35UA Útmutató

17 Augusztus 2024
RDL

RDL EZ-MXA20 Útmutató

17 Augusztus 2024
RDL

RDL HD-MA35U Útmutató

16 Augusztus 2024
RDL

RDL HD-MA35 Útmutató

15 Augusztus 2024
RDL

RDL HD-MA35UA Útmutató

15 Augusztus 2024
RDL

RDL HD-MA35A Útmutató

15 Augusztus 2024

Útmutatók Kézi turmixgép

Legújabb útmutatók Kézi turmixgép

Bosch

Bosch ErgoMixx MFQ36451 Útmutató

8 Április 2025
Girmi

Girmi SB42 Útmutató

6 Április 2025
KitchenAid

KitchenAid 5KHBRV71 Útmutató

1 Április 2025
Black Decker

Black Decker MX1500W Útmutató

31 Március 2025
Sencor

Sencor SHM 9130WH Útmutató

25 Március 2025
Sencor

Sencor SHB 9130WH Útmutató

25 Március 2025
Alto

Alto PBM4 Sistema Útmutató

16 Január 2025
Alto

Alto L-12 Útmutató

16 Január 2025
Alto

Alto S-12 Útmutató

16 Január 2025
Alto

Alto DJM-2 Útmutató

16 Január 2025