Használati útmutató QSC AcousticDesign AD-S32T

QSC hangszóró AcousticDesign AD-S32T

Olvassa el alább 📖 a magyar nyelvű használati útmutatót QSC AcousticDesign AD-S32T (70 oldal) a hangszóró kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/70
AcousticDesign™ Series
User Guide
AD-S6T – 6" two-way , foreground/background loudspeaker with 70/100V transformer
AD-S8T – 8" two-way, foreground/background loudspeaker with 70/100V transformer
AD-S10T – 10" two-way, foreground/background loudspeaker with 70/100V transformer
AD-S12 – 12" two-way, foreground/background loudspeaker
AD-S112sw – 12" direct-radiating subwoofer
TD-000329-00-C
*TD-000329-00*
2
EN
TD-000329-00-C
EXPLANATION OF SYMBOLS
The term “WARNING!” indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily injury or death.
The term “ ” indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it may result in CAUTION!
damage to the equipment that may not be covered under the warranty.
The term “IMPORTANT!” indicates instructions or information that are vital to the successful completion of the procedure.
The term " " is used to indicate additional useful information.NOTE
NOTE:
The intent of the lightning fl ash with arrowhead symbol in a triangle is to alert the user to the presence of un-insulated
"dangerous" voltage within the product's enclosure that may be of suffi cient magnitude to constitute a risk of electric shock to humans.
NOTE:
The intent of the exclamation point within an equilateral triangle is to alert the user to the presence of important safety, and
operating and maintenance instructions in this manual.
IMPORTANT SAFETY INSTRUCTIONS
WARNING!:
TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
WARNING!:
While it is possible for one person to lift a loudspeaker, it is important to use proper lifting techniques. Suggested
reading: OSHA Technical Manual on Back Disorders and Injuries
(http://www.osha.gov/dts/osta/otm/otm_vii/otm_vii_1.html#app_vii:1_2).
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Clean only with a dry cloth.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi ers) that produce heat.
• Only use attachments/accessories specifi ed by the manufacturer.
• Refer all servicing to qualifi ed service personnel.
• Adhere to all applicable, local codes.
• Consult a licensed, professional engineer when any doubt or questions arise regarding a physical equipment installation.
Introduction
AcousticDesign series is a line of premium surface-mount loudspeakers intended for permanent installation applications. Housed in rugged ABS
molded enclosures, each loudspeaker (except the AD-S12 and AD-S112sw) features a 70/100V transformer for use with distributed-audio lines. The
unique X-Mount™ Bracket and Euro-style connector, supplied with each AcousticDesign loudspeaker, are designed for maximum fl exibility and a quick
install. Featuring a knurled ball-mount and discrete angle deployment marks, installers can set loudspeaker deployment angles quickly and securely.
The Euro-style connector allows pre-wiring of the system and when combined with the quick “snap-on” deployment of the loudspeaker to the mount,
installation is completed in a fraction of the time required versus competitive models.
Unpacking
Package Contents
1. Quick-Start Guide
2. AcousticDesign Loudspeaker
3. Euro-style Connector, 4-pin
4. Terminal Weather Protection Cover
5. Phillips Screws (4) M4 (Terminal Weather Protection Cover)
6. X-Mount™ Bracket (Yoke Mount for AD-S112sw)
3
EN
TD-000329-00-C
Set the Transformer Tap Switch
Refer to — Figure 1
1. Insert a 4mm fl at-tip screwdriver into Transformer Tap hole
and engage the slot.
2. At fully clockwise the transformer is in 8 -bypass.
AD-S10T
AD-S6T, AD-S8T
Mount the Loudspeakers
Install the BracketX-Mount™
Refer to — Figure 4
WARNING!:
Install the system in accordance
with local building codes and regulations. Use
a licensed contractor or professional engineer.
QSC Audio Products is not responsible for
damages resulting from the negligent
installation of any bracket or loudspeaker.
1. Mount to a surface capable of supporting the weight of
the loudspeaker.
— Figure 1 —
4mm
100 Volt 70 Volt
8 8 Ω Ω
N/A 100W
100W 50W
50W 25W
25W 12.5W
— Table 1 —
— Figure 2 —
100 Volt 70 Volt
8 8 Ω Ω
N/A 60W
60W 30W
30W 15W
15W 7.5W
— Table 2 —
— Figure 3 —
— Figure 4 —
4
EN
TD-000329-00-C
Adjust the Angle of the X-Mount™ Bracket
Refer to — Figure 5
NOTE:
This step may be done now or after mounting the loudspeaker.
1. Use a 5mm hex wrench to loosen the adjustment locking screws.
2. Orient the bracket as necessary.
3. Tighten the adjustment locking screws.
— Figure 5 —
~
~ +/-70º
-15° +30°
+/-40º
5 mm
Not available
on AD-S6T
~
~ +/-60º (AD-S6T)
SIDE TOP FRONT
5
EN
TD-000329-00-C
Mount the Loudspeaker on the Bracket
Refer to .— Figure 6
NOTE:
The loudspeaker can be placed on the
mount in ANY direction (Up, Down, Left, Right).
1. Align the "X" slot with the X-Mount™ bracket and push the
loudspeaker onto the bracket. (1)
2. When seated, pull the loudspeaker down to lock the
loudspeaker onto the bracket. (2)
3. (Optional) Remove and retain the security tab (3); pull
straight out. To remove the loudspeaker, re-install the
security tab, press in and then remove the loudspeaker.
Connect a Safety Tether (Not supplied)
WARNING!:
DO NOT connect the tether to
the mounting bracket or the screws holding the
mounting bracket.
1. It is recommended that you connect a safety tether from the
safety ring (4) on the back of the loudspeaker to a spot on
the wall that is structurally suffi cient to hold the weight of
the loudspeaker in the event the loudspeaker should fall.
Suspend the Loudspeaker
Refer to — Figure 7
WARNING!:
Suspend the loudspeaker in accordance with local building codes and
regulations. Use a licensed contractor or professional engineer. QSC Audio Products is not
responsible for damages resulting from the negligent installation of suspension cabling, or
loudspeaker.
The AcousticDesign loudspeakers (models AD-S8T, AD-S10T and AD-S12) may be suspended using the pull-
back point and M10 eyebolts you install at the bottom of the enclosures.
NOTE:
Suspending the enclosure woofer side up positions the HF closer to the listener
and helps improve bass response when coupled against the ceiling and wall planes.
1. Remove 2 M10 plugs (not shown) from the bottom of the loudspeaker enclosure.
2. Install two M10 -1.5 eyebolts (2) (accessory M10 Kit-C) in the M10 installation points on the bottom of the
loudspeaker enclosure.
3. Attach an appropriate cable to the tether Safety Ring (3) for the pull-back point.
Yoke-mount the Loudspeaker
In addition to the mounting methods listed above, you can mount the loudspeaker using the optional Yoke mounting kit Refer to instructions
provided in the Yoke kit. See the "Specifi cations" on page 12 for information.
— Figure 6 —
3
1
2
4
— Figure 7 —
2
3
6
EN
TD-000329-00-C
Install the Weather Cover (Optional)
Refer to — Figure 8
1. Slide the nut (1), compression gasket (2), and weather cover / gasket (3) over the
wiring for the loudspeaker.
2. Terminate the wiring to the Euro-style connector, refer to "Wire the Loudspeaker"
on page 6
3. Install the Euro-style connector.
4. Slide the weather cover/gasket (3) up next to the connection box, use a small
amount of wire, inside the cover, to provide strain relief.
5. Attach the weather cover to the enclosure with four screws (supplied).
6. Slide the compression gasket (2) into the weather cover receptacle.
7. Slide the nut over the weather cover receptacle and tighten.
Wire the Loudspeaker
Use up to 12 gage wiring as appropriate. Refer to .— Figure 9
1. If you are using the optional weather cover, make sure the wiring is inserted through all three parts of the weather cover in the proper order.
2. Install the negative and positive wires in the "Input" +/- as shown. Tighten the wire-clamp screws.
3. Install the daisy-chaining wires into the "Thru" +/- as shown. These wires go to the next loudspeaker in the daisy-chain.
Remove the Loudspeaker
1. Make sure all the wiring is disconnected, and the safety tether is removed.
2. If the security tab, located at the base of the loudspeaker mount, has NOT been removed, push the tab in and slide the loudspeaker in the
opposite direction of how it was installed.
3. If the security tab has been removed, re-insert it, or use a small rod (<4 mm / 0.16") to push in and release the mount lock.
— Figure 8 —
1
2
3
— Figure 9 —
7
EN
TD-000329-00-C
AD-S12 Dimensions
— Figure 10 —
596 mm (23.5 in)
354 mm (13.9 in)
354 mm (13.9 in)
322 mm (12.7 in)
322 mm (12.7 in)
596 mm (23.5 in)

Termékspecifikációk

Márka: QSC
Kategória: hangszóró
Modell: AcousticDesign AD-S32T

Szüksége van segítségre?

Ha segítségre van szüksége QSC AcousticDesign AD-S32T, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók hangszóró QSC

QSC

QSC MD-FP152-124r Útmutató

30 Március 2025
QSC

QSC PL-CA6 Útmutató

30 Március 2025
QSC

QSC PL-SUB15 Útmutató

30 Március 2025
QSC

QSC PL-SUB10 Útmutató

30 Március 2025
QSC

QSC MD-FP152-64r Útmutató

30 Március 2025
QSC

QSC PL-SUB12 Útmutató

30 Március 2025
QSC

QSC Wideline 10 WL2102-w Útmutató

13 Január 2025
QSC

QSC HF-63X1 Útmutató

8 Január 2025
QSC

QSC WL115-sw Útmutató

8 Január 2025
QSC

QSC AD-C42T Útmutató

8 Január 2025

Útmutatók hangszóró

Legújabb útmutatók hangszóró

Match

Match UP C42BMW-FRT.3 Útmutató

3 Április 2025
Turbosound

Turbosound PQ12-SB Útmutató

3 Április 2025
Trust

Trust Tytan GXT 658 Útmutató

3 Április 2025
Turbosound

Turbosound PQ15-YB Útmutató

3 Április 2025
Klipsch

Klipsch Synergy KSB-S1 Útmutató

3 Április 2025
Klipsch

Klipsch Synergy KSF-10.5 Útmutató

3 Április 2025
Klipsch

Klipsch kO-R1 Útmutató

3 Április 2025
Klipsch

Klipsch Synergy SB-1 Útmutató

3 Április 2025
Klipsch

Klipsch Reference RB-5 II Útmutató

3 Április 2025
Klipsch

Klipsch Contractor CS-800-R Útmutató

3 Április 2025