Használati útmutató Pyle PLUTV62CHK

Pyle Vevő PLUTV62CHK

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Pyle PLUTV62CHK (8 oldal) a Vevő kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/8
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
PRECAUTIONS
• This unit is designed for negative ground 12-14.50 Volts (DC) operation only.
• Use speakers with an impedance of 4 Ohms
• Avoid installing the unit where:
• It would be subject to high temperatures, such as from direct sunlight or hot air
from the heater.
• It would be exposed to rain or moisture.
• It would be subject to dust or dirt.
• If your vehicle or boat is parked in direct sunlight and there is a considerable
rise in temperature inside the car, allow the unit to cool off before operation.
• When installing the unit horizontally, be sure not to cover the heatsink ns with
the oor carpet.
• If this unit is placed too close to the resources radio, an interference may occur.
In this case, separate the amplier from the car radio.
• This power amplier employs a protection circuit to protect the transistors and
speakers if the amplier malfunctions. Do not attempt to test the protection
circuits by covering the heatsink or connecting improper loads.
• Do not use the unit with a weak auto battery as its optimum performance
depends on a normal battery supply voltage.
• For safety reasons, keep the volume of your audio system moderate so that you
can still hear normal traffic sounds in a reasonable distance.
WIRING INSTRUCTIONS
POWER CONNECTION
The battery terminal (BATT) must be connected directly to the positive terminal of
the vehicle battery to provide an adequate voltage source and minimize noise.
Connecting the battery terminal lead to any other point (such as the fuse block) will
reduce the power output and may cause noise and distortion. Use only #12 gauge or
thicker (smaller gauge #) wire for this lead and connect it to the terminal of the
battery after all other wiring is completed.
GROUND CONNECTION
The ground terminal (GND) connection is also critical to the correct operation of the
amplier. Use a wire of the same gauge as the power connection (#8 or thicker) and
connect it between the ground terminal (GND) of the amplier and a metal part of
the vehicle close to the mounting location. This wire should be as short as possible
and any paint or rust at the grounding point should be scraped away to provide a
clean metal surface to which the end of the ground wire can be screwed or bolted.
REMOTE TURN-ON CONNECTION
The amplier is turned on by applying +12V to the remote turn-on terminal (REM).
The wire lead to this terminal should be connected to the "Auto-Antenna" lead from
the vehicle/or boat stereo resources which will provide the +12V only when the
stereo resources is turned on. If the car stereo does not provide an "Auto-Antenna"
lead, the remote turn-on lead may be wired to an "Accessory" or "Radio" terminal in
the vehicle’s/or boat’s fuse block. This will turn the amplier on and off with the
ignition key, regardless of whether the stereo resources is on or off.
The remote turn-on lead does not carry large currents. So #16 gauge wire may be
used for this application.
SPEAKER CONNECTIONS
Depending on the type and number of speakers used with the amplier wire them
to the speaker terminals as per the appropriate wiring diagram. For most applications
#18 gauge wire should be used for the speaker leads but in no case thinner than
#16 gauge. For leads is excess of 10 feet #12 gauge is recommended. When wiring
the speakers, pay careful attention to the polarity of the terminals on the speakers
and make certain they correspond to the polarity of the corresponding terminals on
the amplier. Do not ground any speaker leads to the chassis of the vehicle/or boat.
OPERATION
After the amplier has been installed and all connections have been made carefully
and securely, turn the radio on so that the amplier is switched on automatically.
After a short power-on period, the amplier reaches its full performance. Now turn
up the volume slowly using the volume control of the radio. If there is no sound or
only a distorted replay, switch off the radio immediately - the amplier will also
switch off automatically - and check if all connections have been made correctly.
GND (-) = GROUND CONNECTION
Connect the GND terminal to the chassis ground of your vehicle/or boat and take
care of best electric and mechanic contact. In doing so, drill a hole into the vehicle/or
boat chassis near the amplier then remove color, dirt or any other substance from
the ground point. Thereafter fasten the cable end with added ring terminal by using
a screw. Ensure that the ground connection is as short as possible and that the cable
diameter is sufficient (min 4mm). Route the ground cables from the radio and all
other equipment parts, like equalizer, active crossover network or other ampliers, to
the same ground point.
www.PyleUSA.com
2www.PyleUSA.com 3
NOTES ON THE POWER SUPPLY
• Connect the +12V power input lead only after all other leads have been connected.
• Be sure to connect the ground wire of the unit securely to a metal part of the
vehicle/or boat.
• Loose or faulty connection may cause amplier malfunction
• The unit is turned on by applying +12 Volts to this terminal. This terminal REM:
does not draw heavy current like the tow Power Terminals so a thinner connecting
wire is acceptable. Standard 18 GAUGE is ne and the standard color is red. If the
radio is equipped with a Power Antenna control wire, it can drive this terminal.
If the Power Antenna wire is already in use, you can still splice into it. With this
method, the unit will turn ON automatically with the radio.
• Use the power supply lead with a fuse attached whose value is the same as original
fuse.
• Place the fuse in the power supply lead as close as possible to the car battery.
• During a full power operation, Maximum current will run through the system.
Therefore, make sure that the leads to be connected to the +12V and GND
terminals of the unit respectively must be larger than 18-Gauge (AWG.18) proper
Bridged operation. If only mono signal is available, a "Y" adapter is required.
FUSE REPLACEMENT
If the fuse blows, check the power connection and replace the fuse. If the fuse blows
again after replacement, there may be an internal malfunction. In this case, consult
your dealer.
WARNING
Use the specied amperage fuse. Use of a higher amperage fuse may cause serious
damage.
+ 12V = POWER SUPPLY
Connect the BATT terminal to the positive pole of the battery with a lead cable and
add a fuse into the power cable in a distance of not more than 30 cm from the
battery. The lead cable’s diameter should be at least 4 mm’ for a length of 3 m and 6
mm” for a length of 6 m.
REM (ON/OFF) REMOTE CONTROL
Connect the REM terminal to the automatic antenna connector of your vehicle/or
boat radio. Now when turning on and off your vehicle/or boat radio, the amplier
automatically switches ON and OFF. A cable diameter of 0.5mm2 is sufficient.
SPEAKERS CONNECTIONS
www.PyleUSA.com
4www.PyleUSA.com 5
L-OUTPUT+ White
L-OUTPUT- White+Black
R-OUTPUT+ eyGr
R-OUTPUT- e BlackGr y+
OUT
OUT
White ( L )
R ( R )ed
Black
+ 12V Red
GND Black
REM Blue
A I tUX npu
AUX Input
Line
POWER CONNECTION LEADS

Termékspecifikációk

Márka: Pyle
Kategória: Vevő
Modell: PLUTV62CHK

Szüksége van segítségre?

Ha segítségre van szüksége Pyle PLUTV62CHK, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Vevő Pyle

Pyle

Pyle PFMRA340BB.5 Útmutató

13 Január 2025
Pyle

Pyle PLMRMBT5B Útmutató

6 December 2024
Pyle

Pyle P3001AT Útmutató

6 December 2024
Pyle

Pyle PLA2200 Útmutató

30 Szeptember 2024
Pyle

Pyle PTAU45.5 Útmutató

22 Szeptember 2024
Pyle

Pyle PWMA3003BT Útmutató

21 Szeptember 2024
Pyle

Pyle PDC22 Útmutató

19 Szeptember 2024
Pyle

Pyle PFA320BT Útmutató

18 Szeptember 2024
Pyle

Pyle PTAUWIFI46 Útmutató

16 Szeptember 2024
Pyle

Pyle PPG-460A Útmutató

13 Szeptember 2024

Útmutatók Vevő

Legújabb útmutatók Vevő

QSC

QSC SPA-Qf 60x2 Útmutató

2 Április 2025
Harper

Harper HDT2-5010 Útmutató

2 Április 2025
Harper

Harper HDT2-2010 Útmutató

2 Április 2025
Alpine

Alpine MRX-F65 Útmutató

31 Március 2025
Streacom

Streacom TL1 Útmutató

31 Március 2025
Pro-Ject

Pro-Ject Stereo Box DS Útmutató

30 Március 2025
Graupner

Graupner GR-8 Útmutató

30 Március 2025
MB Quart

MB Quart FA2-2000.1 Útmutató

29 Március 2025
MB Quart

MB Quart FA2-1500.1 Útmutató

29 Március 2025
MB Quart

MB Quart FA2-1000.1 Útmutató

29 Március 2025